User's Manual
Table Of Contents
- ASTRO® XTL™ 5000 Mobile Radio with W4, W5, W7, and W9 Control Heads User's Guide
- Front Cover
- W4 Quick Reference Card
- W5 Quick Reference Card
- Control Head Front Foldout
- Inside Title Page
- Contents
- Introduction
- Basic Operating Procedures
- General Radio Features
- Often-used Features
- Emergency Call and Alarm
- Scan Operation
- Turn On Scan
- Turn Scan On While Disregarding the Squelch Code (Conventional Modes Only)
- View a Scan List
- Transmit While Scan Is On
- Temporarily Delete a Nuisance Mode With Scan On (W7 and W9 Control Heads Only)
- Restore a Nuisance Mode (W7 and W9 Control Heads Only)
- Change Mode Priorities While Scan Is On (W7 and W9 Control Heads Only)
- Restore Mode Priorities in a Scan List (W7 and W9 Control Heads Only)
- Program a Scan List
- Hang Up Box (HUB)
- Optional External Alarms (Horn and Lights)
- Time-Out Timer
- Push-To-Talk Identification (PTT-ID)
- Conventional Radio Features
- Trunking Operation
- Features Used on Trunking Systems
- Telephone Interconnect List
- Unlimited Telephone Interconnect (W7 and W9 Control Heads Only)
- Enhanced Private Conversation (Digital Modes Only)
- Call Alert Page (Digital Modes Only)
- Failsoft
- Dynamic Regrouping (Digital Modes Only)
- SmartZone® (W7 and W9 Control Heads Only)
- Out-of-Range Indication
- Trunked Announcement
- Secure Operation
- Troubleshooting
- Glossary
- Index
- Control Head Back Foldout
- W7 Quick Reference Card
- W9 Quick Reference Card
- Back Cover
ASTRO
®
XTL™ 5000 Digital
Mobile Radios with W5
Control Head
Quick Reference Card
BASIC OPERATION
Turn the Radio On and Off
Set the Volume and Squelch
Change Modes
Transmit
Transmit (Conventional Modes)
Activate Scan
Program a Scan List
Select Scan Mode Priority
Mode
Vol
Mic
Phon
Call Sel
H/L Mon Dir
PWR
Scan
XMIT
BUSY
DIM
HOME
MODE
POWER
ON/OFF
PAGE
or
SECURE
or
EMERGENCY
Page
Emer
PHONE
SCAN
CALL
SELECT
VOLUME
PRIORITY/
NON-PRIORITY
INDICATORS
DIRECT
INDICATOR
HORN/
LIGHTS
MONITOR
DIRECT
HOME
Press the PWR button once.
1 Hold the Vol rocker button down to increase or
decrease volume as desired, then release.
The display shows volume levels from
0 to 15.
2 On conventional modes with Private-Line or Digital
Private-Line, press
Mon or remove the microphone
from the hang-up clip to defeat the coded squelch.
3 Press Mon again, or replace the microphone on the
hang-up clip to return to coded-squelch operation.
4 To adjust squelch level, hold Mon until a tone sounds.
5 Press the Mode rocker button to select squelch level.
6 Press HOME.
Press the Mode rocker button to select the desired
mode
OR
Press HOME to access the preprogrammed Home
mode.
1 Press and hold the microphone PTT button.
2 When the transmit light comes on solid and no alert
tones sound (or a talk-permit tone or ID sidetone
sounds), speak into the microphone in a normal voice.
3 State your FCC call sign at the beginning of each
transmission.
1 Press Dir (Direct). The Dir indicator lights.
2
Press Dir again to return to repeater operation.
1 Press Scan to start a scan. If no activity exists, the
display shows your selected mode. When a scanned
channel or talkgroup becomes active, the display
shows the active mode name. The
PRI and NPRI
indicators show priority.
2 Press Scan again to stop scanning.
1 Hold Scan until a tone sounds and the scan indicator
blinks.
2 Press the Mode rocker button to select the mode you
want to program.
3 Press the Sel button as indicated in the table below to
add or remove the displayed mode from the scan list.
4 Repeat the previous steps to continue editing the list.
5 Press HOME or Scan to exit.
Press Sel Mode Indicator
One time Non-Priority
NPRI lit
Two times Second Priority
PRI lit
Three times First Priority
PRI blinks
Four times Delete from List No indicator
1 Press the Sel button as indicated in the table above
to designate up to two modes as priorities.
2 Press HOME or Scan to end scan list selection.