Installation Manual
Table Of Contents
- Chapter 3 Universal Relay Controller Installation
- Chapter 4 Options and Accessories Installation
- 4.1 Dash-Mount Accessory Installation
- 4.2 Remote-Mount Accessory Installation
- 4.2.1 Emergency Pushbutton or Footswitch Installation
- 4.2.2 Horn (External Alarm) Relay Installation
- 4.2.3 Lights (External Alarm) Relay Installation
- 4.2.4 Gunlock Installation
- 4.2.5 Horn-Ring Transfer
- 4.2.6 Record Audio Out Jack of Transmit and Receive Audio
- 4.2.7 Earphone Jack
- 4.2.8 USB Data Cables
- 4.2.9 RS232 Cables
- 4.3 Vehicle Interface Port Overview
- 4.4 Compatibility of Emergency when Attaching a Siren
- 4.5 Accessory Connector Assembly Details (P2) (All Models Except 100W)
- 4.6 Memory and Three-Day Secure Key Retention Option
- Chapter 5 Motorcycle Radio Installation
- 5.1 Motorcycle Radio Description
- 5.2 Installation Overview
- 5.3 Installing the Universal Mounting Plate
- 5.4 Installing the Speaker and Control Head
- 5.4.1 Handlebar Installation with Speaker and Control Head Mounted Together
- 5.4.2 Fuel Tank Console Installation with Speaker and Control Head Mounted Together
- 5.4.3 Handlebar Installation with Speaker and Control Head Mounted Separately
- 5.4.4 Fuel Tank Console Installation with Speaker and Control Head Mounted Separately
- 5.5 Installing the Speaker
- 5.6 Installing the Microphone Hang-Up Clip
- 5.7 Installing Antenna Base and Cables
- 5.8 Installing the Antenna
- 5.9 Cable Routing
- 5.10 Installing the Weather-Resistant Enclosure
- 5.11 Transceiver and Cabling Installation
- 5.12 Installing the Emergency Switch Option
- 5.13 Installing the External Alarm Relay Option
- 5.14 Installing the Headset Accessory
- 5.15 Installing the Control Head Sunshield
- 5.16 Horn/Lights Wiring
- 5.17 Emergency Switch Wiring
- Chapter 6 Finishing the Installation
- Chapter 7 Best Practices: Installation & Troubleshooting
- 7.1 Check Wiring of Ignition and Radio Ignition Sensing
- 7.2 Check Physical Installation of Radio Ground and Radio Accessory Wiring
- 7.3 Improve the Electrical Quality of the Power and Ignition Lines
- 7.4 Minimize the Effect of Poorly Grounded Antennas
- 7.5 Jump-Start the Vehicle
- 7.6 Eliminate Noise/Howling from PA Speaker
- A.1 Basic Ordering Information
- A.2 Motorola Online
- A.3 Mail Orders
- A.4 Telephone Orders
- A.5 Fax Orders
- A.6 Parts Identification
- A.7 Product Customer Service
6878215A01
Universal Relay Controller Installation: O9 Universal Relay Controller Cable Assembly 3-3
3.2 O9 Universal Relay Controller Cable Assembly
3.2.1 Power Cable
1. Remove the cap nut of power cable gland assembly, and insert the power cable through the
cap nut and neoprene seal in the cable gland body. Use power cable with either AWG 6 or
AWG 8 only (recommended OD range of cable is 5.5 mm to 9 mm) that is able to withstand
80 A and 50 A respectively, to ensure water sealing of the controller. User can decide to
install one or two power cables based on the requirements. The power cables (A+) are not
supplied.
2. The loose end of the power cable with cable strip length 7.94 mm (5/16”) is then placed on
the power lug and secured down by a set screw. The cap nut is then reassembled with
tightening torque 18 lb-in.
3. The other end of the power cable should be connected to circuit breaker (Motorola part
number 40012006001) end which indicates "AUX" and then, to power supply on the other
end which indicates "BAT", instead of connecting to power supply directly.
4. Repeat steps 1 to 3 to install the second power cable, if required.
5. If only one power cable is installed, it is recommended to cover the other side of the power
cable gland with power cable gland seal with tightening torque 18 lb-in.
3.2.2 Ground Cable
1. Remove the cap nut of ground cable gland assembly, insert the ground cable through the cap
nut and then reassemble the cap nut. Use ground cable with AWG 14 only (recommended
OD range of cable is 2 mm to 4 mm) that is able to withstand 5 A. The ground cables (A+) are
not supplied.
NOTE: The ground is used to switch the relays, and not act as a ground to the actual device being
controlled.
2. The loose end of the ground cable with cable strip length 7.94 mm (5/16”) is then connected
to a two-pin terminal block. Both pins on the terminal block are inter-connected and either pin
can be used. The cap nut is then reassembled with tightening torque 7 lb-in.
Figure 3-3. Power and Ground Cable Glands
Ground Cable Gland
Power Cable Gland