Installation Manual
Table Of Contents
- Chapter 3 Universal Relay Controller Installation
- Chapter 4 Options and Accessories Installation
- 4.1 Dash-Mount Accessory Installation
- 4.2 Remote-Mount Accessory Installation
- 4.2.1 Emergency Pushbutton or Footswitch Installation
- 4.2.2 Horn (External Alarm) Relay Installation
- 4.2.3 Lights (External Alarm) Relay Installation
- 4.2.4 Gunlock Installation
- 4.2.5 Horn-Ring Transfer
- 4.2.6 Record Audio Out Jack of Transmit and Receive Audio
- 4.2.7 Earphone Jack
- 4.2.8 USB Data Cables
- 4.2.9 RS232 Cables
- 4.3 Vehicle Interface Port Overview
- 4.4 Compatibility of Emergency when Attaching a Siren
- 4.5 Accessory Connector Assembly Details (P2) (All Models Except 100W)
- 4.6 Memory and Three-Day Secure Key Retention Option
- Chapter 5 Motorcycle Radio Installation
- 5.1 Motorcycle Radio Description
- 5.2 Installation Overview
- 5.3 Installing the Universal Mounting Plate
- 5.4 Installing the Speaker and Control Head
- 5.4.1 Handlebar Installation with Speaker and Control Head Mounted Together
- 5.4.2 Fuel Tank Console Installation with Speaker and Control Head Mounted Together
- 5.4.3 Handlebar Installation with Speaker and Control Head Mounted Separately
- 5.4.4 Fuel Tank Console Installation with Speaker and Control Head Mounted Separately
- 5.5 Installing the Speaker
- 5.6 Installing the Microphone Hang-Up Clip
- 5.7 Installing Antenna Base and Cables
- 5.8 Installing the Antenna
- 5.9 Cable Routing
- 5.10 Installing the Weather-Resistant Enclosure
- 5.11 Transceiver and Cabling Installation
- 5.12 Installing the Emergency Switch Option
- 5.13 Installing the External Alarm Relay Option
- 5.14 Installing the Headset Accessory
- 5.15 Installing the Control Head Sunshield
- 5.16 Horn/Lights Wiring
- 5.17 Emergency Switch Wiring
- Chapter 6 Finishing the Installation
- Chapter 7 Best Practices: Installation & Troubleshooting
- 7.1 Check Wiring of Ignition and Radio Ignition Sensing
- 7.2 Check Physical Installation of Radio Ground and Radio Accessory Wiring
- 7.3 Improve the Electrical Quality of the Power and Ignition Lines
- 7.4 Minimize the Effect of Poorly Grounded Antennas
- 7.5 Jump-Start the Vehicle
- 7.6 Eliminate Noise/Howling from PA Speaker
- A.1 Basic Ordering Information
- A.2 Motorola Online
- A.3 Mail Orders
- A.4 Telephone Orders
- A.5 Fax Orders
- A.6 Parts Identification
- A.7 Product Customer Service
Chapter 6 Finishing the Installation
6.1 Cable Connection
6.1.1 O9 Control Head
Perform the following if it has not been previously done:
1. Remove the control head from its mounting trunnion. Plug the radio's CAN cable into the
proper location on the back of the control head (see Figure 2-22 and Figure 2-24 in
Chapter 2). The connectors “click” when snapped into place. The control head model can
have the microphone plugged into the CGAI connection on the control head back panel.
2. Connect the plug from the speaker lead to the mating connector coming out of the power
cable.
3. Plug the VIP connector into the correct location on the back of the control head.
4. Connect the CAN cable to the proper location on the transceiver.
6.1.2 O5 Control Head
Perform the following if it has not been previously done:
1. Remove the control head from its mounting trunnion. Plug the radio's CAN cable into the
proper location on the back of the control head (see Figure 2-21 and Figure 2-23 in
Chapter 2). The connectors “click” when snapped into place. The control head model can
have the microphone plugged into the lower left corner of the control head front panel.
2. Connect the plug from the speaker lead to the mating connector coming out of the power
cable.
3. Plug the VIP connector into the correct location on the back of the control head.
4. Connect the CAN cable to the proper location on the transceiver.