Installation Manual
Table Of Contents
- Chapter 3 Universal Relay Controller Installation
- Chapter 4 Options and Accessories Installation
- 4.1 Dash-Mount Accessory Installation
- 4.2 Remote-Mount Accessory Installation
- 4.2.1 Emergency Pushbutton or Footswitch Installation
- 4.2.2 Horn (External Alarm) Relay Installation
- 4.2.3 Lights (External Alarm) Relay Installation
- 4.2.4 Gunlock Installation
- 4.2.5 Horn-Ring Transfer
- 4.2.6 Record Audio Out Jack of Transmit and Receive Audio
- 4.2.7 Earphone Jack
- 4.2.8 USB Data Cables
- 4.2.9 RS232 Cables
- 4.3 Vehicle Interface Port Overview
- 4.4 Compatibility of Emergency when Attaching a Siren
- 4.5 Accessory Connector Assembly Details (P2) (All Models Except 100W)
- 4.6 Memory and Three-Day Secure Key Retention Option
- Chapter 5 Motorcycle Radio Installation
- 5.1 Motorcycle Radio Description
- 5.2 Installation Overview
- 5.3 Installing the Universal Mounting Plate
- 5.4 Installing the Speaker and Control Head
- 5.4.1 Handlebar Installation with Speaker and Control Head Mounted Together
- 5.4.2 Fuel Tank Console Installation with Speaker and Control Head Mounted Together
- 5.4.3 Handlebar Installation with Speaker and Control Head Mounted Separately
- 5.4.4 Fuel Tank Console Installation with Speaker and Control Head Mounted Separately
- 5.5 Installing the Speaker
- 5.6 Installing the Microphone Hang-Up Clip
- 5.7 Installing Antenna Base and Cables
- 5.8 Installing the Antenna
- 5.9 Cable Routing
- 5.10 Installing the Weather-Resistant Enclosure
- 5.11 Transceiver and Cabling Installation
- 5.12 Installing the Emergency Switch Option
- 5.13 Installing the External Alarm Relay Option
- 5.14 Installing the Headset Accessory
- 5.15 Installing the Control Head Sunshield
- 5.16 Horn/Lights Wiring
- 5.17 Emergency Switch Wiring
- Chapter 6 Finishing the Installation
- Chapter 7 Best Practices: Installation & Troubleshooting
- 7.1 Check Wiring of Ignition and Radio Ignition Sensing
- 7.2 Check Physical Installation of Radio Ground and Radio Accessory Wiring
- 7.3 Improve the Electrical Quality of the Power and Ignition Lines
- 7.4 Minimize the Effect of Poorly Grounded Antennas
- 7.5 Jump-Start the Vehicle
- 7.6 Eliminate Noise/Howling from PA Speaker
- A.1 Basic Ordering Information
- A.2 Motorola Online
- A.3 Mail Orders
- A.4 Telephone Orders
- A.5 Fax Orders
- A.6 Parts Identification
- A.7 Product Customer Service
6878215A01
3-2 Universal Relay Controller Installation: Universal Relay Controller Mounting
Install the URC as follows:
1. Use the URC trunnion as a template to mark the mounting holes;
drill 5/32" holes. If mounting on a plastic surface, use a metal backing plate.
2. Attach the trunnion bracket using all four 10 – 16" x 5/8" self-tapping screws provided.
3. Temporarily install the URC (adjust for proper viewing angle) and fasten it to the trunnion with
two wing screws. Test the installation to ensure that the unit is securely locked in place.
Figure 3-2. Universal Relay Controller Installation Exploded View
ADJUST THE UNIVERSAL RELAY
CONTROLLER TO DESIRED
ANGLE AND SECURE WITH WING
SCREWS
USE FOUR MOUNTING SCREWS
ON ALL INSTALLATIONS
TRUNNION
DRILL FOUR 5/32'' HOLES
IN MOUNTING SURFACE
MOUNTING SURFACE
IMPORTANT
USE A METAL BACKING PLATE
(NOT SUPPLIED) IF MOUNTING
TRUNNION ON PLASTIC OR
UNSTABLE SURFACE