Installation Manual
Table Of Contents
- Chapter 3 Universal Relay Controller Installation
- Chapter 4 Options and Accessories Installation
- 4.1 Dash-Mount Accessory Installation
- 4.2 Remote-Mount Accessory Installation
- 4.2.1 Emergency Pushbutton or Footswitch Installation
- 4.2.2 Horn (External Alarm) Relay Installation
- 4.2.3 Lights (External Alarm) Relay Installation
- 4.2.4 Gunlock Installation
- 4.2.5 Horn-Ring Transfer
- 4.2.6 Record Audio Out Jack of Transmit and Receive Audio
- 4.2.7 Earphone Jack
- 4.2.8 USB Data Cables
- 4.2.9 RS232 Cables
- 4.3 Vehicle Interface Port Overview
- 4.4 Compatibility of Emergency when Attaching a Siren
- 4.5 Accessory Connector Assembly Details (P2) (All Models Except 100W)
- 4.6 Memory and Three-Day Secure Key Retention Option
- Chapter 5 Motorcycle Radio Installation
- 5.1 Motorcycle Radio Description
- 5.2 Installation Overview
- 5.3 Installing the Universal Mounting Plate
- 5.4 Installing the Speaker and Control Head
- 5.4.1 Handlebar Installation with Speaker and Control Head Mounted Together
- 5.4.2 Fuel Tank Console Installation with Speaker and Control Head Mounted Together
- 5.4.3 Handlebar Installation with Speaker and Control Head Mounted Separately
- 5.4.4 Fuel Tank Console Installation with Speaker and Control Head Mounted Separately
- 5.5 Installing the Speaker
- 5.6 Installing the Microphone Hang-Up Clip
- 5.7 Installing Antenna Base and Cables
- 5.8 Installing the Antenna
- 5.9 Cable Routing
- 5.10 Installing the Weather-Resistant Enclosure
- 5.11 Transceiver and Cabling Installation
- 5.12 Installing the Emergency Switch Option
- 5.13 Installing the External Alarm Relay Option
- 5.14 Installing the Headset Accessory
- 5.15 Installing the Control Head Sunshield
- 5.16 Horn/Lights Wiring
- 5.17 Emergency Switch Wiring
- Chapter 6 Finishing the Installation
- Chapter 7 Best Practices: Installation & Troubleshooting
- 7.1 Check Wiring of Ignition and Radio Ignition Sensing
- 7.2 Check Physical Installation of Radio Ground and Radio Accessory Wiring
- 7.3 Improve the Electrical Quality of the Power and Ignition Lines
- 7.4 Minimize the Effect of Poorly Grounded Antennas
- 7.5 Jump-Start the Vehicle
- 7.6 Eliminate Noise/Howling from PA Speaker
- A.1 Basic Ordering Information
- A.2 Motorola Online
- A.3 Mail Orders
- A.4 Telephone Orders
- A.5 Fax Orders
- A.6 Parts Identification
- A.7 Product Customer Service
6878215A01
Options and Accessories Installation: Accessory Connector Assembly Details (P2) (All Models Except 100W) 4-11
4.5.1.2 Assembly
1. Place the plug in one cover. Be sure that the flange of the plug is in the slot of the cover.
See Figure 4-11.
2. Push the jackscrew through the plug to hold it in.
3. Position each wire across the strain-relief features in the cover. Avoid damaging loads on the
plug by allowing some slack in each wire in the accessory connector assembly’s wire
chamber.
4. Place the second cover onto the plug. Be sure that the flange is protruding through both
covers.
Figure 4-11. Exploded View of Accessory Connector Assembly (HLN6863_)
5. Squeeze the covers together bending the wires in the strain-relief features. You may need a
pair of pliers to seat the assembly covers.
6. Once the covers are fully seated, fasten them with the cover screws. Tighten the screws
firmly but do not over-tighten them. Be sure none of the wires are pinched.
7. Reattach the accessory connector assembly to the back of the radio and fasten it by
finger-tightening the jackscrews to prevent any loosening.
NOTE: See APX 7500 Basic Service Manual (6875964M01) for more detailed descriptions of these
pins and other connectors located in the APX 7500 mobile radio.