Installation Manual
Table Of Contents
- Chapter 3 Universal Relay Controller Installation
- Chapter 4 Options and Accessories Installation
- 4.1 Dash-Mount Accessory Installation
- 4.2 Remote-Mount Accessory Installation
- 4.2.1 Emergency Pushbutton or Footswitch Installation
- 4.2.2 Horn (External Alarm) Relay Installation
- 4.2.3 Lights (External Alarm) Relay Installation
- 4.2.4 Gunlock Installation
- 4.2.5 Horn-Ring Transfer
- 4.2.6 Record Audio Out Jack of Transmit and Receive Audio
- 4.2.7 Earphone Jack
- 4.2.8 USB Data Cables
- 4.2.9 RS232 Cables
- 4.3 Vehicle Interface Port Overview
- 4.4 Compatibility of Emergency when Attaching a Siren
- 4.5 Accessory Connector Assembly Details (P2) (All Models Except 100W)
- 4.6 Memory and Three-Day Secure Key Retention Option
- Chapter 5 Motorcycle Radio Installation
- 5.1 Motorcycle Radio Description
- 5.2 Installation Overview
- 5.3 Installing the Universal Mounting Plate
- 5.4 Installing the Speaker and Control Head
- 5.4.1 Handlebar Installation with Speaker and Control Head Mounted Together
- 5.4.2 Fuel Tank Console Installation with Speaker and Control Head Mounted Together
- 5.4.3 Handlebar Installation with Speaker and Control Head Mounted Separately
- 5.4.4 Fuel Tank Console Installation with Speaker and Control Head Mounted Separately
- 5.5 Installing the Speaker
- 5.6 Installing the Microphone Hang-Up Clip
- 5.7 Installing Antenna Base and Cables
- 5.8 Installing the Antenna
- 5.9 Cable Routing
- 5.10 Installing the Weather-Resistant Enclosure
- 5.11 Transceiver and Cabling Installation
- 5.12 Installing the Emergency Switch Option
- 5.13 Installing the External Alarm Relay Option
- 5.14 Installing the Headset Accessory
- 5.15 Installing the Control Head Sunshield
- 5.16 Horn/Lights Wiring
- 5.17 Emergency Switch Wiring
- Chapter 6 Finishing the Installation
- Chapter 7 Best Practices: Installation & Troubleshooting
- 7.1 Check Wiring of Ignition and Radio Ignition Sensing
- 7.2 Check Physical Installation of Radio Ground and Radio Accessory Wiring
- 7.3 Improve the Electrical Quality of the Power and Ignition Lines
- 7.4 Minimize the Effect of Poorly Grounded Antennas
- 7.5 Jump-Start the Vehicle
- 7.6 Eliminate Noise/Howling from PA Speaker
- A.1 Basic Ordering Information
- A.2 Motorola Online
- A.3 Mail Orders
- A.4 Telephone Orders
- A.5 Fax Orders
- A.6 Parts Identification
- A.7 Product Customer Service
6878215A01
4-4 Options and Accessories Installation: Remote-Mount Accessory Installation
4.2.2 Horn (External Alarm) Relay Installation
Mount the horn relay in a suitable location (normally under the dash). Connect the relay contacts
across the horn ring switch, typically found in the steering column. Connect the two control wires to a
SW B+ pin and a VIP OUT pin on the VIP connector.
4.2.3 Lights (External Alarm) Relay Installation
Mount the light relay in a suitable location (normally under the dash). Connect the relay contacts
across the head lamp ON/OFF switch. Connect the two control wires to a SW B+ pin and a VIP OUT
pin on the VIP connector.
4.2.4 Gunlock Installation
The O9 control head is capable to program up to three gunlocks to any programming buttons. You
can define as momentary trigger or with a time-out trigger button. Connect the relay contacts across
the gunlock switch to install the gunlock. Connect the two control wires to a SW B+ pin and a VIP
OUT pin on the VIP connector.
It is recommended to install a failsafe/redundant bypass switch for the gunlock. It is suggested to use
a separate timer switch or a manual push-on button switch to activate the gunlock. Connect the
switch from the supply to the gunlock directly, as shown in Figure 4-4. Place the manual button at a
suitable and reachable location, yet not easily seen.
Figure 4-4. Gunlock Switch Redundancy Diagram
Transceiver
and
control head
VIP Cable
VIP OUT
GND
GND
GND
Gunlock
Redundancy
Wiring
Car Battery
Momentary or
time-out bypass
manual switch