Installation Manual
Table Of Contents
- Foreword
- Installation Requirements for Compliance with Radio Frequency (RF) Energy Exposure Safety Standards
- Table of Contents
- Mobile Radio Model Numbering Scheme
- Commercial Warranty
- Chapter 1 Introduction
- Chapter 2 Standard Configurations
- 2.1 Planning the Installation
- 2.2 Radio Mounting
- 2.2.1 Dash Mount with Trunnion
- 2.2.2 Remote Mount with Trunnion
- 2.2.2.1 Transceiver
- 2.2.2.2 Control Head and Remote Mount Cabling
- 2.2.3 Locking Kit (Optional)
- 2.3 Power Cable
- 2.4 Ignition Sense Cable
- 2.5 Antenna Installation
- 2.6 Speaker
- 2.7 Microphone Hang-Up Clip
- 2.8 Completing the Installation
- Chapter 3 Options and Accessories Installation
- Chapter 4 Motorcycle Radio Installation
- 4.1 Motorcycle Radio Description
- 4.2 Installation Overview
- 4.3 Installing the Universal Mounting Plate
- 4.4 Installing the Speaker and Control Head
- 4.4.1 Handlebar Installation with Speaker and Control Head Mounted Together
- 4.4.2 Fuel Tank Console Installation with Speaker and Control Head Mounted Together
- 4.4.3 Handlebar Installation with Speaker and Control Head Mounted Separately
- 4.4.4 Fuel Tank Console Installation with Speaker and Control Head Mounted Separately
- 4.5 Installing the Speaker
- 4.6 Installing the Microphone Hang-Up Clip
- 4.7 Installing Cables
- 4.8 Installing the Weather-Resistant Enclosure
- 4.9 Transceiver and Cabling Installation
- 4.10 Installing the Antenna
- 4.11 Installing the Emergency Switch Option
- 4.12 Installing the External Alarm Relay Option
- 4.13 Installing the Headset Accessory
- 4.14 Horn/Lights Wiring
- 4.15 Emergency Switch Wiring
- Chapter 5 Finishing the Installation: Cable Connection
- Appendix A Replacement Parts Ordering
- Glossary
- Index
6881098C38-O September 17, 2004
Standard Configurations: Planning the Installation 2-3
2.1.2 Wiring Diagrams
Figure 2-7 through Figure 2-11 show the wiring diagrams for all the possible configurations. The title
under each figure identifies which model control head is being shown. Identify which of these figures
shows the configuration that you are installing, and use the diagram when planning the installation.
Figure 2-7. Radio Installation (Dash Mount) Using W4, W5, or W7 Control Heads
(Cannot Be Used for 100W Radios)
(For complete pin configuration, see
Figure 3-9.)
PWR
Mode
Scan
Phon Sel
Call
Vol
DIM
HOME
XMIT
BUSY
123
45
6
78 9
0
Sts Msg
H/L Mon Dir
Rcl Del
MIC
BATTERY
HORN
RELAY
LIGHT
RELAY
MIC
CLIP
SPEAKER
MIC
EMERGENCY
SWITCH
FUSE
FUSE
BLOCK
(+)
(-)
REDLEAD
FUSE
FIREWALL
HOLE
MOUNTING
SCREW
CONTROLHEAD*
*MODELW7SHOWN
ANTENNA
CONNECTION
ANTENNA
MAEPF-27612-O
IGNITIONCABLE
P2
(SEEJ2
PINOUT)
DC
POWER
CABLE
TRUNNION
J2
REARACCESSORYCONNECTOR
1
7
8
14
13
20
21
26
SPKR-
SPKR+
VIPOUT2
12V
(RELAY)
VIPOUT1
12V
(RELAY)
GROUND
EMERGENCY
IGNITION