Installation Manual
Table Of Contents
- Foreword
- Installation Requirements for Compliance with Radio Frequency (RF) Energy Exposure Safety Standards
- Table of Contents
- Mobile Radio Model Numbering Scheme
- Commercial Warranty
- Chapter 1 Introduction
- Chapter 2 Standard Configurations
- 2.1 Planning the Installation
- 2.2 Radio Mounting
- 2.2.1 Dash Mount with Trunnion
- 2.2.2 Remote Mount with Trunnion
- 2.2.2.1 Transceiver
- 2.2.2.2 Control Head and Remote Mount Cabling
- 2.2.3 Locking Kit (Optional)
- 2.3 Power Cable
- 2.4 Ignition Cable
- 2.5 Antenna Installation
- 2.6 Speaker
- 2.7 Microphone Hang-Up Clip
- 2.8 Completing the Installation
- Chapter 3 Options and Accessories Installation
- Chapter 4 Motorcycle Radio Installation
- 4.1 Motorcycle Radio Description
- 4.2 Installation Overview
- 4.3 Installing the Universal Mounting Plate
- 4.4 Installing the Speaker and Control Head
- 4.4.1 Handlebar Installation with Speaker and Control Head Mounted Together
- 4.4.2 Fuel Tank Console Installation with Speaker and Control Head Mounted Together
- 4.4.3 Handlebar Installation with Speaker and Control Head Mounted Separately
- 4.4.4 Fuel Tank Console Installation with Speaker and Control Head Mounted Separately
- 4.5 Installing the Speaker
- 4.6 Installing the Microphone Hang-Up Clip
- 4.7 Installing Cables
- 4.8 Installing the Weather-Resistant Enclosure
- 4.9 Transceiver and Cabling Installation
- 4.10 Installing the Antenna
- 4.11 Installing the Emergency Switch Option
- 4.12 Installing the External Alarm Relay Option
- 4.13 Installing the Headset Accessory
- 4.14 Horn/Lights Wiring
- 4.15 Emergency Switch Wiring
- Chapter 5 Finishing the Installation: Cable Connection
- Appendix A Replacement Parts Ordering
- Glossary
- Index
6881096C72-B September 9, 2003
Options and Accessories Installation: Remote-Mount Accessory Installations for W4/5/7/9 Models 3-3
b. Secure all wires using tie straps or appropriate electrical tape to insure the wire’s safety.
Any wires passing through the vehicle’s metal panels must be protected with grommets.
This will prevent the shaving of the wire’s protective jacket, which will result in a short.
2. The second method is to use the accessory connector assembly (not supplied with the
remote mount configuration). The process is similar to the dash mount process (see
Section
3.3 on page 3-4). DO NOT connect two of the same accessories simultaneously at the rear of
the control head and the accessory connector assembly (e.g., two emergency switches
would both need to be engaged in order to operate).
3.2.1 Emergency Pushbutton, Footswitch, Horn Relay, and Light Relay Installation
Perform the following installation procedure:
1. Select an appropriate place to mount the option or accessory hardware.
2. Connect male-pin control leads (wires) to the VIP connector in the appropriate location (see
Table 3-1 and Table 3-2). Figure 3-1 shows how wires are plugged into the connector and
how to use an extraction tool to remove wires.
3. Route the accessory-to-control head cables under floor coverings or behind panels so that
the vehicle occupants do not snag or break the wires.
Figure 3-1. VIP Connector Detail
3.2.1.1 Emergency Pushbutton or Footswitch Installation
Mount the switch using the hardware that comes with the kit. Connect the emergency switch wires to
a ground pin and a VIP IN pin on the VIP connector.
3.2.1.1.1 W9 Control Head
1. Remove JU23 (emergency to ground) from the W9 control head.
2. Connect a jumper wire between pin 27 (emergency) and pin 3 (VIP IN 2) of P103 inside the
W9 control head.
3. Remove R84 (if installed) from the W9 control head.
4. Install the emergency switch between pins 3 (VIP IN 2) and 20 (ground) of the control head
back connector.
CAUTION: When connecting the various microphones available,
make sure to attach the S-hook provided on the microphone cable
(see
Figure 2-13 in Chapter 2) to the dash or remote mount
trunnion to avoid damage to the microphone control head
interconnect.
!
C a u t i o n
VIP
GASKET
EXTRACTION
TOOL
WIRE
VIP
CONNECTOR
CRIMPED
RECEPTACLE
MAEPF-21424-O