User's Manual
Table Of Contents
- Introduction
- Product Description
- Technology and Benefits
- Applications
- Configuration Options – RF, IP, DFS
- Power and Grounding
- Administration Systems
- Specifications
- Radio specifications (common to all formats)
- Specifications for PMP 430 (5.4 & 5.8-GHz) SM and PTP 230 (5.4 & 5.8-GHz) BH radio with integrated antenna
- Specifications for PMP 400 (4.9 & 5.4-GHz) AP/SM and PTP 200 (4.9 & 5.4-GHz) BH radio with integrated antenna
- Specification for PMP 400/430 AP and PTP 200 BH connectorized radio
- Specifications for PMP 400/430 kitted, connectorized radio (antenna included)
- Performance
- Planning
- Configuring
- Installation
- Regulatory and Legal Notices
- Important Note on Modifications
- National and Regional Regulatory Notices
- U.S. Federal Communication Commission (FCC) Notification
- Industry Canada (IC) Notification
- Regulatory Requirements for CEPT Member States (www.cept.org)
- European Union Notification for 5.8 GHz Product
- Equipment Disposal
- EU Declaration of Conformity for RoHS Compliance
- UK Notification
- Luxembourg Notification
- Czech Republic Notification
- Greece Notification
- Brazil Notification
- Labeling and Disclosure Table for China
- Exposure Separation Distances
- Legal Notices
- Limit of Liability
PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 8 of 77
Software Release 8.4.3 features
Issue 3
Added the following 4.9-GHz public safety band products:
PTP 200 Series – 4.9-GHz BHs
PMP 400 Series – 4.9-GHz APs and SMs
Software Release 9.4.2 features
Issue 4
Added the following:
Software Release 9.5 features to support PMP 400 and PTP 200
PMP 430 Series – 5.8-GHz APs and SMs
Software Release 10.0 features to support PMP 430 (10MHz channel)
Updated customer support email and phone numbers
Issue 5
Added the following:
PMP 430 Series 5.4-GHz AP and SM
PMP 430 Series (5.4 and 5.8-GHz OFDM) with Release 10.3
o Configurable 5, 10 and 20 MHz channel bandwidth
Note: PMP 400 Series 5.4-GHz OFDM supports 10MHz channels.
o 2.5MHz center channels when configured for 5MHz channel bandwidth
o Added support for 1/16 Cyclic Prefix in addition to 1/4 and 1/8
Note: PMP 400 Series 5.4-GHz OFDM supports 1/4 Cyclic Prefix
o Increased Packets Per Second (PPS) from 6,800 to 15,000 PPS
o 802.1ad Q-in-Q DVLAN (Double VLAN) tagging
o Dynamic Rate Adapt – configurable (1X, 2X, 3X) uplink/downlink rate
PMP 400 and PTP 200 Series with Release 10.3
o 802.1ad Q-in-Q DVLAN (Double VLAN) tagging
o Dynamic Rate Adapt – configurable(1X, 2X, 3X) uplink/downlink rate
Issue 6
Added the following:
PTP 230 Series 5.4 and 5.8-GHz BHM and BHS
1.2 ABBREVIATIONS
The following abbreviations may be used in these notes:
1X
1X (QPSK) modulation
2X
2X (16 QAM) modulation
3X
3X (64 QAM) modulation
AES
AP
Advanced Encryption Standard
Access Point Module
BH
Backhaul Module, either timing master or timing slave
BHM
Backhaul Module – Master
BHS
CAP
CIR
Backhaul Module – Slave
Access Point Module
Committed Information Rate
CMM
Cluster Management Module (CMM4 or CMMicro)
CNUT
CSM
Canopy Network Updater Tool
Subscriber Module
DES
DFS
Data Encryption Standard
Dynamic Frequency Selection for radar avoidance