User's Manual
8-34
PMP320HDW2v1
Preliminary
JUL
2010
10MHz
26.5
36
7MHz 25
34.5
5MHz 24
33.5
3.5MHz 23
32.5
10MHz
14
36
7MHz 13
35
5MHz 12
34
3.5MHz 11.5
33.5
Industry
Canada
Notification
Chapter
8:
Regulatory,
Legal,
and
Safety
Notices
Table
8-1
FCC
IDs
and
the
specific
configurations
(Continued)
Maximum
FCC
ID
Operating
Frequency
Model
Number
Antenna
Gain
Channel
Size
T
ransmitter
Output
Power
Maximum
allowed
EIRP
ABZ89FT7636
3.650
GHz
to
3.675
GHz
3630SMC
9.5
ABZ89FT7636
3.650
GHz
to
3630SMC 22
3.675
GHz
Industry
Canada
Notification
This
device
is
approved
for
use
in
Canada
in
the
licensed
frequencies
from
3.450
GHz
to
3.700
GHz.
It
is
undergoing
Industry
Canada
approval
for
use
in
the
3.65
GHz
band,
and
may
not
be
used
in
that
band
until
Industry
Canada
approval
is
granted.
Operation
is
subject
to
the
following
two
conditions:
•
This
device
may
not
cause
harmful
interference
and
•
This
device
must
accept
any
interference
received,
including
interference
that
may
cause
undesired
operation.
This
equipment
has
been
tested
and
found
to
comply
with
the
limits
for
a
Class
B
digital
device.
These
limits
are
designed
to
provide
reasonable
protection
against
harmful
interference
in
a
residential
installation.
This
equipment
generates,
uses,
and
can
radiate
radio
-
frequency
energy
and
if
not
installed
and
used
in
accordance
with
these
instructions,
may
cause
harmful
interference
to
radio
communications.
If
this
equipment
does
cause
harmful
interference
to
radio
or
television
reception,
which
can
be
determined
by
turning
the
equipment
on
and
off
,
the
user
is
encouraged
to
correct
the
interference
by
one
or
more
of
the
following
measures:
•
Increase
the
separation
between
the
affected
equipment
and
the
unit;
•
Connect
the
affected
equipment
to
a
power
outlet
on
a
different
circuit
from
that
which
the
receiver
is
connected
to;
•
Consult
the
dealer
and/or
experienced
radio/TV
technician
for
help.
T
o
reduce
potential
radio
interference
to
other
users,
the
antenna
type
and
its
gain
should
be
chosen
so
its
Equivalent
Isotropic
R
adiated
P
ower
(EIRP)
is
not
more
than
that
permitted
for
successful
communication.
For 3630APC (3600~3650 MHz)
This device has been designed to operate with an antenna having a maximum gain of 17 dBi. Antenna having a higher gain
is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
For 3630APC (3650~3700MHz)
This device has been designed to operate with an antenna having a maximum gain of 16.5 dBi. Antenna having a higher
gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
For 3530SMC/3630SMC
This device has been designed to operate with an antenna having a maximum gain of 22 dBi. Antenna having a higher gain
is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
PMP
320
Hardware
Installation
European
Union
Notification