User's Manual
Table Of Contents
- 1 Introduction
- 2 Product Description
- 2.1 TECHNOLOGY AND BENEFITS
- 2.2 APPLICATIONS
- 2.3 CONFIGURATION OPTIONS – RF, IP, DFS
- 2.4 POWER AND GROUNDING
- 2.5 ADMINISTRATION SYSTEMS
- 2.6 SPECIFICATIONS
- 2.6.1 Radio specifications (common to all formats)
- 2.6.2 Specifications for PMP 430 SM radio with integrated antenna
- 2.6.3 Specifications for PMP 430 SM radio with optional LENS
- 2.6.4 Specifications for PMP 400 and PTP 200 radio with integrated antenna
- 2.6.5 Specification for PMP 400 and 430 connectorized radio
- 2.6.6 Specifications for PMP 400/430 kitted, connectorized radio (antenna included)
- 2.7 PERFORMANCE
- 3 Planning
- 4 Configuring
- 4.1 LINK OPERATION – 1X/2X/3X
- 4.2 TRANSMITTER OUTPUT POWER (AND NO JITTER)
- 4.3 DOWNLINK DATA %, RANGE, AND CONTROL SLOTS
- 4.4 DFS AND REGULATORY PARAMETERS FOR 5.8 & 5.4 GHZ RADIOS
- 4.5 NET ANTENNA GAIN FIELD
- 4.6 NETWORK CONTROL PARAMETERS
- 4.7 FORWARD ERROR CORRECTION
- 4.8 CYCLIC PREFIX (CONFIGURABLE ONLY ON PTP 200 BH & PMP 430 AP/SM)
- 5 Installation
- 6 Regulatory and Legal Notices
- 6.1 IMPORTANT NOTE ON MODIFICATIONS
- 6.2 NATIONAL AND REGIONAL REGULATORY NOTICES
- 6.2.1 U.S. Federal Communication Commission (FCC) Notification
- 6.2.2 Industry Canada (IC) Notification
- 6.2.3 Regulatory Requirements for CEPT Member States (www.cept.org)
- 6.2.4 Equipment Disposal
- 6.2.5 EU Declaration of Conformity for RoHS Compliance
- 6.2.6 Luxembourg Notification
- 6.2.7 Czech Republic Notification
- 6.2.8 Greece Notification
- 6.2.9 Brazil Notification
- 6.2.10 Labeling and Disclosure Table for China
- 6.3 EXPOSURE SEPARATION DISTANCES
- 6.4 LEGAL NOTICES
- 6.5 LIMIT OF LIABILITY
PMP 400/430 and PTP 200 Series Canopy User Guide
Supplement
Issue 4 0 – DRAFT 6 November 2009 Page 46 of 64
5 Installation
WARNING!
Installing a unit usually involves height, electricity, and exposure to RF
(Radio Frequency) energy. To avoid personal injury, follow applicable
national and local safety regulations along with industry best practices.
Also follow the specific guidelines in this document, including Exposure
Separation Distances in section 6.3 on page 60.
5.1 INSTALLING AN AP WITH CONNECTORIZED ANTENNA
This section addresses installation aspects specific to the PMP 400/430 and PTP 200 Series AP.
General communications equipment, infrastructure, and facilities site design should be performed
in line with Motorola’s “Standards and Guidelines for Communications Sites” (also known as the
R56 manual - document #68P81089E50-A)
These procedures are specific to the case of as AP purchased as a kit consisting of a
connectorized antenna and a connectorized radio. They are also generally applicable to
connectorized APs, SMs, or BHs when the antenna is purchased separately by the operator.
A short coaxial cable from the radio terminates in a male N connector. The antenna has a
chassis-mounted female N connector. The antenna includes tower mount brackets with
adjustable down-tilt.
Installing an AP typically consists of four phases:
1. Configuring the AP at an operator's facility or at the installation site using the
information and settings defined previously in Planning (Section 3) and Configuring
(Section 4).
2. Assembling the AP (radio and antenna and brackets) and physically installing it using
Procedure 2 for 5.8 and 5.4 GHz APs or Procedure 3 for 4.9 GHz APs, along with
physically installing a CMMmicro (for PMP 54400 AP only) or CMM4 (for either PMP
58430, 54400 or PMP 49400).
3. Cabling the AP to the CMMmicro (for PMP 54400 AP only) or CMM4 (for either PMP
58430, 54400 or PMP 49400), and grounding it to Protective Earth – PE using
Procedure 4. This phase can also include cabling to backhauls, or running terrestrial
feeds.
4. Confirming operation, using SMs in the field.
Local practices and choices of installation options will dictate the actual processes. For example,
variations on these generalized procedures can be used to install on a building or install multiple
APs on a pipe mount before hoisting up a tower for final attachment.