User's Manual
Table Of Contents
- 1 Introduction
- 2 Product Description
- 2.1 TECHNOLOGY AND BENEFITS
- 2.2 APPLICATIONS
- 2.3 CONFIGURATION OPTIONS – RF, IP, DFS
- 2.4 POWER AND GROUNDING
- 2.5 ADMINISTRATION SYSTEMS
- 2.6 SPECIFICATIONS
- 2.6.1 Radio specifications (common to all formats)
- 2.6.2 Specifications for PMP 430 SM radio with integrated antenna
- 2.6.3 Specifications for PMP 430 SM radio with optional LENS
- 2.6.4 Specifications for PMP 400 and PTP 200 radio with integrated antenna
- 2.6.5 Specification for PMP 400 and 430 connectorized radio
- 2.6.6 Specifications for PMP 400/430 kitted, connectorized radio (antenna included)
- 2.7 PERFORMANCE
- 3 Planning
- 4 Configuring
- 4.1 LINK OPERATION – 1X/2X/3X
- 4.2 TRANSMITTER OUTPUT POWER (AND NO JITTER)
- 4.3 DOWNLINK DATA %, RANGE, AND CONTROL SLOTS
- 4.4 DFS AND REGULATORY PARAMETERS FOR 5.8 & 5.4 GHZ RADIOS
- 4.5 NET ANTENNA GAIN FIELD
- 4.6 NETWORK CONTROL PARAMETERS
- 4.7 FORWARD ERROR CORRECTION
- 4.8 CYCLIC PREFIX (CONFIGURABLE ONLY ON PTP 200 BH & PMP 430 AP/SM)
- 5 Installation
- 6 Regulatory and Legal Notices
- 6.1 IMPORTANT NOTE ON MODIFICATIONS
- 6.2 NATIONAL AND REGIONAL REGULATORY NOTICES
- 6.2.1 U.S. Federal Communication Commission (FCC) Notification
- 6.2.2 Industry Canada (IC) Notification
- 6.2.3 Regulatory Requirements for CEPT Member States (www.cept.org)
- 6.2.4 Equipment Disposal
- 6.2.5 EU Declaration of Conformity for RoHS Compliance
- 6.2.6 Luxembourg Notification
- 6.2.7 Czech Republic Notification
- 6.2.8 Greece Notification
- 6.2.9 Brazil Notification
- 6.2.10 Labeling and Disclosure Table for China
- 6.3 EXPOSURE SEPARATION DISTANCES
- 6.4 LEGAL NOTICES
- 6.5 LIMIT OF LIABILITY
PMP 400/430 and PTP 200 Series Canopy User Guide
Supplement
Issue 4 0 – DRAFT 6 November 2009 Page 55 of 64
6 Regulatory and Legal Notices
6.1 IMPORTANT NOTE ON MODIFICATIONS
Intentional or unintentional changes or modifications to the equipment must not be made unless
under the express consent of the party responsible for compliance. Any such modifications could
void the user’s authority to operate the equipment and will void the manufacturer’s warranty.
6.2 NATIONAL AND REGIONAL REGULATORY NOTICES
6.2.1 U.S. Federal Communication Commission (FCC) Notification
For 5.4-GHz devices:
This device complies with Part 15 of the US FCC Rules and Regulations. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) This
device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the US FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio-frequency energy and, if not installed and used in accordance with
these instructions, may cause harmful interference to radio communications. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment on and off, the user is encouraged to correct the interference by one or
more of the following measures:
• Increase the separation between the affected equipment and the unit;
• Connect the affected equipment to a power outlet on a different circuit from that
which the receiver is connected to;
• Consult the dealer and/or experienced radio/TV technician for help.
For 4.9-GHz devices:
The 4.9-GHz band is a licensed band allocated to public safety services. State and local
government entities that provide public safety services are eligible to apply for 4.9 GHz licenses.
For additional information, refer to FCC regulations.
FCC IDs and the specific configurations covered are listed in
Table 13.