User's Guide
Table Of Contents
- Contents
- List of Tables
- Software Version
- Read Me First
- Preparing Your Radio for Use
- Radio Controls
- Status Indicators
- General Radio Operation
- Advanced Features
- 6.1 Advanced Call Features
- 6.2 Scan Lists
- 6.3 Scan
- 6.4 Call Alert Paging
- 6.5 Emergency Operation
- 6.5.1 Special Considerations for Emergency Operation
- 6.5.2 Emergency Keep-Alive
- 6.5.3 Exiting Emergency Operation
- 6.5.4 Exiting Emergency as Supervisor (Trunking Only)
- 6.5.5 Sending an Emergency Alarm
- 6.5.6 Sending an Emergency Call (Trunking Only)
- 6.5.7 Sending An Emergency Call With Hot Mic (Trunking Only)
- 6.5.8 Sending an Emergency Alarm with Emergency Call
- 6.5.9 Sending An Emergency Alarm and Call with Hot Mic
- 6.5.10 Sending a Silent Emergency Alarm
- 6.5.11 Emergency Find Me
- 6.6 Fireground
- 6.7 Tactical Public Safety (Conventional Only)
- 6.8 Man Down
- 6.9 Secure Operations
- 6.10 Radio Inhibit
- 6.11 Global Positioning System/Global Navigation Satellite System
- 6.12 Mission Critical Geofence (ASTRO 25 Trunking)
- 6.13 Trunking System Controls
- 6.14 Mission Critical Wireless Bluetooth®
- 6.14.1 Turning On Bluetooth
- 6.14.2 Turning Off the Bluetooth
- 6.14.3 Pairing with Low Frequency-Motorola Proximity Pairing (LF-MPP) Feature
- 6.14.4 Standard Pairing Feature
- 6.14.5 Turning On the Bluetooth Audio
- 6.14.6 Turning Off the Bluetooth Audio
- 6.14.7 Adjusting the Volume of the Radio from Bluetooth Audio Device
- 6.14.8 Clearing All Bluetooth Devices Information
- 6.14.9 Pairing with LEX Handheld
- 6.14.10 Responder Alert Sensors
- 6.15 ASTRO 25 (P25) Programming Over Project 25 (POP25)
- 6.16 Voice Announcement
- 6.17 Site Selectable Alerts (ASTRO 25 Trunking)
- 6.18 Wi-Fi
- 6.19 Utilities
- 6.19.1 Using the Flip Display
- 6.19.2 Selecting a Basic Zone Bank
- 6.19.3 Selecting the Power Level
- 6.19.4 Controlling the Display Backlight
- 6.19.5 Locking and Unlocking the Controls
- 6.19.6 Turning Voice Mute On or Off
- 6.19.7 Using the Time-Out Timer
- 6.19.8 Conventional Squelch Operation
- 6.19.9 Using the PL Defeat Feature
- 6.19.10 Digital PTT ID Support
- 6.19.11 Smart PTT (Conventional Only)
- 6.19.12 Transmit Inhibit
- 6.19.13 Instant Recall
- Accessories
- Legal and Compliance Statement
- Maritime Radio Use in the VHF Frequency Range
- Limited Warranty
- Glossary
- ACK
- Active Channel
- Analog Signal
- ARS
- ASTRO 25
- ASTRO conventional
- Autoscan
- Bluetooth
- Bluetooth Pairing
- Call Alert
- Carrier Squelch
- Central Controller
- Channel
- Control Channel
- Conventional
- Conventional Scan List
- COTS
- Cursor
- Digital Private Line (DPL)
- Digital Signal
- Dispatcher
- Digital Signal Processor
- Dynamic Regrouping
- Failsoft
- FCC
- Hang up
- IV&D
- Key Variable Loader
- Liquid-Crystal Display (LCD)
- Light Emitting Diode (LED)
- Li-Ion
- Man Down
- MCW
- MDC
- Monitor
- Multi-System Talkgroup Scan List
- Network Access Code
- NiMH
- Non-tactical/revert
- OCW
- Over-The-Air Rekeying
- Page
- Personality
- Preprogrammed
- Private (Conversation) Call
- Private Line (PL)
- Programmable
- Push-to-Talk
- Radio Frequency
- Repeater
- selective switch
- Squelch
- Synchronous Serial Interface (SSI)
- Standby
- Status Calls
- Tactical/non-revert
- TalkAround
- Talkgroup
- Trunking
- Trunking Priority Monitor scan list
- USK
- VRS
- Zone
6.14.5
Turning On the Bluetooth Audio
Procedure:
• Turning on the Bluetooth audio using the preprogrammed button:
a. Press the preprogrammed Bluetooth Audio Reroute button to route the audio from the
radio to the headset.
You hear a short, medium-pitched tone. The display shows HDSET ON.
BT audio routing can be configured in CPS to route the audio to RSM or radio's internal speaker.
The audio routes to the radio's speaker if RSM is not connected. Check with your dealer or
system administrator for more information on the programming of this feature.
NOTICE: For BT PTT press, the active microphone can be configured in CPS to transmit
from either the RSM, the radio microphone, or the BT headset. If the configured device
is not available, audio transmission reverts to BT headset.
6.14.6
Turning Off the Bluetooth Audio
Procedure:
• Turning off the Bluetooth audio using the preprogrammed button:
a. Press the preprogrammed Bluetooth Audio Reroute button to route the audio from the
headset to the radio.
You hear a short, medium-pitched tone. The display shows SPKR ON.
6.14.7
Adjusting the Volume of the Radio from Bluetooth Audio Device
Prerequisites: Ensure that the Bluetooth audio device is connected to the radio.
When and where to use:
Your radio can only control the volume of MCW and OCW Bluetooth enabled audio device. If the radio
is paired with other Bluetooth enabled audio device, its volume is independent from the APX radio. In
this case, the volume is only adjustable on the device.
Procedure:
Adjust volume up/down on the Bluetooth audio device.
The radio display shows VOL XX and sounds a short, medium-pitched tone.
6.14.8
Clearing All Bluetooth Devices Information
Procedure:
• Clearing all Bluetooth devices information using the preprogrammed Bluetooth On/Off button:
a. Long press the preprogrammed Bluetooth On/Off button.
You hear a short, medium-pitched tone. The display shows PLS WAIT to indicate clearing is
in progress.
MN006727A01-AA
Advanced Features
65