User's Guide
Table Of Contents
- Contents
- List of Tables
- Software Version
- Read Me First
- Preparing Your Radio for Use
- Radio Controls
- Status Indicators
- General Radio Operation
- Advanced Features
- 6.1 Advanced Call Features
- 6.2 Scan Lists
- 6.3 Scan
- 6.4 Call Alert Paging
- 6.5 Emergency Operation
- 6.5.1 Special Considerations for Emergency Operation
- 6.5.2 Emergency Keep-Alive
- 6.5.3 Exiting Emergency Operation
- 6.5.4 Exiting Emergency as Supervisor (Trunking Only)
- 6.5.5 Sending an Emergency Alarm
- 6.5.6 Sending an Emergency Call (Trunking Only)
- 6.5.7 Sending An Emergency Call With Hot Mic (Trunking Only)
- 6.5.8 Sending an Emergency Alarm with Emergency Call
- 6.5.9 Sending An Emergency Alarm and Call with Hot Mic
- 6.5.10 Sending a Silent Emergency Alarm
- 6.5.11 Emergency Find Me
- 6.6 Fireground
- 6.7 Tactical Public Safety (Conventional Only)
- 6.8 Man Down
- 6.9 Secure Operations
- 6.10 Radio Inhibit
- 6.11 Global Positioning System/Global Navigation Satellite System
- 6.12 Mission Critical Geofence (ASTRO 25 Trunking)
- 6.13 Trunking System Controls
- 6.14 Mission Critical Wireless Bluetooth®
- 6.14.1 Turning On Bluetooth
- 6.14.2 Turning Off the Bluetooth
- 6.14.3 Pairing with Low Frequency-Motorola Proximity Pairing (LF-MPP) Feature
- 6.14.4 Standard Pairing Feature
- 6.14.5 Turning On the Bluetooth Audio
- 6.14.6 Turning Off the Bluetooth Audio
- 6.14.7 Adjusting the Volume of the Radio from Bluetooth Audio Device
- 6.14.8 Clearing All Bluetooth Devices Information
- 6.14.9 Pairing with LEX Handheld
- 6.14.10 Responder Alert Sensors
- 6.15 ASTRO 25 (P25) Programming Over Project 25 (POP25)
- 6.16 Voice Announcement
- 6.17 Site Selectable Alerts (ASTRO 25 Trunking)
- 6.18 Wi-Fi
- 6.19 Utilities
- 6.19.1 Using the Flip Display
- 6.19.2 Selecting a Basic Zone Bank
- 6.19.3 Selecting the Power Level
- 6.19.4 Controlling the Display Backlight
- 6.19.5 Locking and Unlocking the Controls
- 6.19.6 Turning Voice Mute On or Off
- 6.19.7 Using the Time-Out Timer
- 6.19.8 Conventional Squelch Operation
- 6.19.9 Using the PL Defeat Feature
- 6.19.10 Digital PTT ID Support
- 6.19.11 Smart PTT (Conventional Only)
- 6.19.12 Transmit Inhibit
- 6.19.13 Instant Recall
- Accessories
- Legal and Compliance Statement
- Maritime Radio Use in the VHF Frequency Range
- Limited Warranty
- Glossary
- ACK
- Active Channel
- Analog Signal
- ARS
- ASTRO 25
- ASTRO conventional
- Autoscan
- Bluetooth
- Bluetooth Pairing
- Call Alert
- Carrier Squelch
- Central Controller
- Channel
- Control Channel
- Conventional
- Conventional Scan List
- COTS
- Cursor
- Digital Private Line (DPL)
- Digital Signal
- Dispatcher
- Digital Signal Processor
- Dynamic Regrouping
- Failsoft
- FCC
- Hang up
- IV&D
- Key Variable Loader
- Liquid-Crystal Display (LCD)
- Light Emitting Diode (LED)
- Li-Ion
- Man Down
- MCW
- MDC
- Monitor
- Multi-System Talkgroup Scan List
- Network Access Code
- NiMH
- Non-tactical/revert
- OCW
- Over-The-Air Rekeying
- Page
- Personality
- Preprogrammed
- Private (Conversation) Call
- Private Line (PL)
- Programmable
- Push-to-Talk
- Radio Frequency
- Repeater
- selective switch
- Squelch
- Synchronous Serial Interface (SSI)
- Standby
- Status Calls
- Tactical/non-revert
- TalkAround
- Talkgroup
- Trunking
- Trunking Priority Monitor scan list
- USK
- VRS
- Zone
assigned Priority Talkgroup.Priority Dispatch is not available during Emergency operations. Scan
feature is suspended when Priority Dispatch is initiated.
Prerequisites: Dispatch console that supports this feature must be preprogrammed to use this feature.
Check with your dealer or system administrator for more information on dispatch console supporting
this feature.
Procedure:
1 Press the preprogrammed Priority Dispatch button.
A tone sounds and the radio enters Priority Dispatch mode. The radio exits this mode when the
Priority Dispatch Time Out Timer expires.
2 Before the Priority Dispatch Time Out Timer expires, press and hold the PTT button to transmit.
The display shows the Priority Talkgroup alias.
3 Release the PTT button to listen.
The radio exits Priority Dispatch mode, returns to its original talkgroup, and displays the home
channel alias.
6.1.3
Dynamic Regrouping (Trunking Only)
This feature allows the dispatcher to temporarily reassign selected radios to a particular channel to
communicate with each other.
When your radio is dynamically regrouped, it receives a dynamic regrouping command and
automatically switches to the dynamically regrouped channel. You hear a tone and the display shows
the name of the dynamically regrouped channel.
When the dispatcher cancels dynamic regrouping, the radio automatically returns to the previous zone
and channel.
If you access a zone or channel that has been reserved as a dynamically regrouped mode for other
users, you hear an invalid tone.
6.1.3.1
Classification of Regrouped Radios
The dispatcher can classify regrouped radios into Select Enabled or Select Disabled categories.
Select Enabled
Select-enabled radios are free to change to any available channel, including the dynamic-
regrouping channel, once you have selected the dynamic-regrouping position.
Select Disabled
Select-disabled radios cannot change channels while dynamically regrouped. The radio is forced to
remain on the dynamic-regrouping channel.
The Scan and Private Call features are unavailable when your radio is Select Disabled.
MN006727A01-AA
Advanced Features
41