User's Manual

ManualsBrandsMotorola Solutions ManualsElectronicsPortable VoWLAN Transceiver with Bluetooth

5 6 74

Hearing Aids

Some digital Enterprise WiFi Phone with wireless radios may interfere with some

hearing aids. In the event of such interference, you may want to consult your hearing aid

manufacturer to discuss alternatives.

When some wireless devices are used near some hearing devices (hearing aids and

cochlear implants), users may detect a buzzing, humming, or whining noise. Some

hearing devices are more immune than others to this interference noise, and wireless

devices also vary in the amount of interference they generate. In the event of

interference you may want to consult your hearing aid supplier to discuss solutions.

Other Medical Devices

If you use any other personal medical device, consult the manufacturer of your device to

determine if it is adequately shielded from RF energy. Your physician may be able to

assist you in obtaining this information.

Use of Communication Devices While Driving

Always check the laws and regulations on the use of radios in the areas where you

drive.

•

Give full attention to driving and to the road.

•

Use hands-free operation, if available.

•

Pull off the road and park before making or answering a call, if driving conditions or

regulations so require.

For Vehicles with Air Bags

Refer to vehicle manufacturer's manual prior to installation of electronic equipment to

avoid interference with air bag wiring.

Do not place the Enterprise WiFi Phone in the area over an air bag or in the air bag

deployment area. Air bags inflate with great force. If an Enterprise WiFi Phone is placed

in the air bag deployment area and the air bag inflates, the Enterprise WiFi Phone may

be propelled with great force and cause serious injury to occupants of the vehicle.

Potentially Explosive Atmospheres

(Explosive atmospheres refer to hazard classified locations that may contain

hazardous gas, vapors, or dusts.)

Turn off your Enterprise WiFi Phone prior to entering any area with a potentially

explosive atmosphere. Do not remove, install, or charge batteries in such areas. Sparks

in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily

injury or even death.

The areas with potentially explosive atmospheres referred to above include fuelling

areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas

where the air contains chemicals or particles, such as grain, dust or metal powders.

Areas with potentially explosive atmospheres are often but not always posted.

Blasting Caps and Blasting Areas

To avoid possible interference with blasting operations, turn off your Enterprise WiFi

Phone when you are near electrical blasting caps, in a blasting area, or in areas posted:

"Turn off radio". Obey all signs and instructions.

Power Supply

Use ONLY a LISTED Motorola, Type no. PWRS-14000 (5Vdc, 850mA), direct plug-in

power supply, marked Class 2 or LPS (IEC60950-1, SELV). Use of alternative Power

Supply will invalidate any approvals given to this unit and may be dangerous.

Batteries

All batteries can cause property damage and/or bodily injury such as burns if a

conductive material such as jewelry, keys, or beaded chains touch exposed terminals.

The conductive material may complete an electrical circuit (short circuit) and become

quite hot. Exercise care in handling any charged battery, particularly when placing it

inside a pocket, purse, or other container with metal objects.

Taiwan - Recycling

EPA (Environmental Protection Administration) requires dry

battery producing or importing firms in accordance with Article 15

of the Waste Disposal Act are required to indicate the recycling

marks on the batteries used in sales, giveaway or promotion.

Contact a qualified Taiwanese recycler for proper battery

disposal.

Battery Information

Use only Motorola approved batteries. Accessories which have battery charging

capability are approved for use with the following battery models:

Motorola BK10 (3.7 Vdc, 1750 mAh) for EWP3200 and BK10 (3.7 Vdc, 1750 mAh) and

BK90 (3.7 Vdc, 1480 mAh) for EWP2200.

Motorola rechargeable battery packs are designed and constructed to the highest

standards within the industry.

However, there are limitations to how long a battery can operate or be stored before

needing replacement. Many factors affect the actual life cycle of a battery pack, such as

heat, cold, harsh environmental conditions and severe drops.

When batteries are stored over six (6) months, some irreversible deterioration in overall

battery quality may occur. Store batteries at half of full charge in a dry, cool place,

removed from the equipment to prevent loss of capacity, rusting of metallic parts and

electrolyte leakage. When storing batteries for one year or longer, the charge level

should be verified at least once a year and charged to half of full charge.

Replace the battery when a significant loss of run time is detected.

Standard warranty period for all Motorola batteries is Three (3) months, regardless if the

battery was purchased separately or included as part of the mobile computer or bar

code scanner. For more information on Motorola batteries, please visit:

http://www.mysymbolcare.symbol.com/battery/batbasics1.html

Battery Safety Guidelines

•

The area in which the units are charged should be clear of debris and combustible

materials or chemicals. Particular care should be taken where the device is charged

in a non commercial environment.

•

Follow battery usage, storage, and charging guidelines found in the user's guide.

•

Improper battery use may result in a fire, explosion, or other hazard.

•

To charge the mobile device battery, the battery and charger temperatures must be

between +32ºF and +104ºF (0ºC and +40ºC)

•

Do not use incompatible batteries and chargers. Use of an incompatible battery or

charger may present a risk of fire, explosion, leakage, or other hazard. If you have

any questions about the compatibility of a battery or a charger, contact Motorola

Enterprise Mobility support.

•

For devices that utilize a USB port as a charging source, the device shall only be

connected to products that bear the USB-IF logo or have completed the USB-IF

compliance program.

•

Do not disassemble or open, crush, bend or deform, puncture, or shred.

•

Severe impact from dropping any battery-operated device on a hard surface could

cause the battery to overheat.

•

Do not short circuit a battery or allow metallic or conductive objects to contact the

battery terminals.

•

Do not modify or remanufacture, attempt to insert foreign objects into the battery,

immerse or expose to water or other liquids, or expose to fire, explosion, or other

hazard.

•

Do not leave or store the equipment in or near areas that might get very hot, such as

in a parked vehicle or near a radiator or other heat source. Do not place battery into

a microwave, oven or dryer.

•

Battery usage by children should be supervised.

•

Please follow local regulations to promptly dispose of used re-chargeable batteries.

•

Do not dispose of batteries in fire.

•

Seek medical advice immediately if a battery has been swallowed.

•

In the event of a battery leak, do not allow the liquid to come in contact with the skin

or eyes. If contact has been made, wash the affected area with large amounts of

water and seek medical advice.

•

If you suspect damage to your equipment or battery, contact Motorola Enterprise

Mobility support to arrange for inspection.

Radio Frequency Interference Requirements-FCC

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

•

Reorient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver

•

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

•

Consult the dealer or an experienced radio/TV technician for help.

Radio Transmitters (Part 15)

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

For RLAN Devices:

The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:

•

Restricted Band 5.60 – 5.65 GHz

This device complies with RSS 210 of Industry Canada.

Operation is subject to the following two conditions: (1) this device may not cause

harmful interference and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux

appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions

suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce

dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de

provoquer un fonctionnement indésirable.

Label Marking: The Term “IC:” before the radio certification only signifies that Industry

Canada technical specifications were met.

The use of 2.4 GHz RLAN's, for use through the EEA, have the following restrictions:

•

Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -

2.4835 GHz

•

France, outside usage is restricted to 2.4 - 2.454 GHz.

•

Italy requires a user license for outside usage.

Bluetooth

Wireless Technology for use through the EEA has the following restrictions:

•

Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -

2.4835 GHz

•

France, outside usage is restricted to 10mW EIRP

•

Italy requires a user license for outside usage.

Motorola hereby, declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of

Conformity may be obtained from:

www.motorola.com/enterprisemobility/doc

Korea Warning Statement for Class B ITE

Other Countries

Australia

Use of 5GHz RLAN's in Australia is restricted in the following band 5.50 - 5.65GHz.

Brazil

Declarações Regulamentares para EWP2200 e EWP3200

Nota: "A marca de certificação se aplica ao Transceptor, modelo EWP2200 e

EWP3200. Este equipamento opera em caráter secundário, isto é, não tem direito a

proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não

pode causar interferência a sistemas operando em caráter primário."

Para maiores informações sobre ANATEL consulte o site: www.anatel.gov.br

CHILE

Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de

telecomunicaciones, relativa a radiaciones electromagnéticas.

Mexico

Restrict Frequency Range to: 2.450 - 2.4835 GHz.

S. Korea

해당 무선설비는 운용 중 전파혼신 가능성이 있음

해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 .

Taiwan

Waste Electrical and Electronic

Equipment (WEEE)

English: For EU Customers: All products at the end of their life must be returned to Motorola for recycling. For

information on how to return product, please go to: