User's Manual
Table Of Contents
- COMPUTER SOFTWARE COPYRIGHTS
- Notational Conventions
- Welcome
- What is the HC700-G Handheld Computer?
- Unpacking
- HC700-G Features
- Charging the Battery
- Figure 3. HC700-G Personal Desktop Cradle
- Battery Replacement
- Figure 4. Battery Installation and Removal
- 1. Hold down the Power Button for at least four seconds until the HC700-G screen turns off.
- 2. Remove the HC700-G hand-strap (see Figure 4).
- 3. Press the battery snap on the battery (see Figure 4) and pull away the battery from the HC700-G.
- 4. Insert a fresh battery, bottom end first, into the battery compartment.
- 5. Carefully, press the battery top downward until it clicks and locks in place.
- 6. Press the Power Button - the HC700-G is now ready for use.
- First Time Battery Charge
- Routine Battery Charge
- Battery Maintenance
- Battery Disposal
- To Prevent Injury or Burns
- Using the HC700-G
- Starting to Work
- Turning On
- Turning Off
- Suspend Mode
- The Status LED
- The Application LED
- Making a Call
- Voice Recording
- Using the Keypad
- Direct Action Keys
- Scanning Barcodes and Capturing Images
- Figure 7. Capturing Images with the HC700-G Imager
- 1. Run the Bcr barcode reader application: Start Menu- >Programs->Sample Applications->Bcr.
- 2. Aim and hold the HC700-G at 2 to 12 inches (5 to 30 cm) distance from the target.
- 3. Press one of the Scan keys and aim the green aiming bar towards the target to adjust your posi...
- Resetting the HC700-G
- Mini SD Memory Card
- Installing a Mini SD Card
- Mini SD Card Handling Precautions
- SIM Card Installation
- Figure 12. SIM Card Installation
- 1. Remove the battery.
- 2. Open the SIM card door
- 3. Slide the SIM card holder forward to unlock the SIM card
- 4. Slide the new SIM card in the holder with the cut corner on the upper right and the gold plate...
- 5. Lower the SIM card holder and press downward to lock the SIM card holder
- 6. Close the SIM card door
- 7. Install the battery
- Service
- ActiveSync (USB) Connectivity
- Troubleshooting
25
Troubleshooting
Table 4: Troubleshooting the HC700-G
Problem Cause Solution
HC700-G
does not turn
on
HC700-G in
Suspend mode
Press the Power Button
battery is
drained
Replace with fresh battery
Battery is not
installed prop-
erly or not
charged
Ensure proper battery
installation in HC700-G.
Charge or replace the bat-
tery
Battery con-
tacts are dirty.
Remove the battery and
clean the battery contacts
as described in “Cleaning”
on page 23.
Battery does
not charge in
HC700-G
Cradle
HC700-G is not
locked in the
HC700-G Cra-
dle
Re-install the HC700-G in
the HC700-G Cradle. Place
the HC700-G properly in
HC700-G Cradle. (Verify
that the HC700-G Cradle
LED is On and charge for
three hours)
HC700-G Cra-
dle contacts are
not clean
Clean contacts and remove
dust and objects from
within the HC700-G Cradle
Battery temper-
ature is out of
range (Status
LED flashes yel-
low)
Ensure that the battery
temperature is within
range. (refer to “Charging
the Battery” on page 6). If
battery remains hot,
replace battery (defective
battery).
Defective bat-
tery
Replace battery
Enhanced IMD Users.book Page 25 Thursday, February 9, 2006 11:52 AM