User's Manual
Table Of Contents
- COMPUTER SOFTWARE COPYRIGHTS
- Notational Conventions
- Welcome
- What is the HC700-G Handheld Computer?
- Unpacking
- HC700-G Features
- Charging the Battery
- Figure 3. HC700-G Personal Desktop Cradle
- Battery Replacement
- Figure 4. Battery Installation and Removal
- 1. Hold down the Power Button for at least four seconds until the HC700-G screen turns off.
- 2. Remove the HC700-G hand-strap (see Figure 4).
- 3. Press the battery snap on the battery (see Figure 4) and pull away the battery from the HC700-G.
- 4. Insert a fresh battery, bottom end first, into the battery compartment.
- 5. Carefully, press the battery top downward until it clicks and locks in place.
- 6. Press the Power Button - the HC700-G is now ready for use.
- First Time Battery Charge
- Routine Battery Charge
- Battery Maintenance
- Battery Disposal
- To Prevent Injury or Burns
- Using the HC700-G
- Starting to Work
- Turning On
- Turning Off
- Suspend Mode
- The Status LED
- The Application LED
- Making a Call
- Voice Recording
- Using the Keypad
- Direct Action Keys
- Scanning Barcodes and Capturing Images
- Figure 7. Capturing Images with the HC700-G Imager
- 1. Run the Bcr barcode reader application: Start Menu- >Programs->Sample Applications->Bcr.
- 2. Aim and hold the HC700-G at 2 to 12 inches (5 to 30 cm) distance from the target.
- 3. Press one of the Scan keys and aim the green aiming bar towards the target to adjust your posi...
- Resetting the HC700-G
- Mini SD Memory Card
- Installing a Mini SD Card
- Mini SD Card Handling Precautions
- SIM Card Installation
- Figure 12. SIM Card Installation
- 1. Remove the battery.
- 2. Open the SIM card door
- 3. Slide the SIM card holder forward to unlock the SIM card
- 4. Slide the new SIM card in the holder with the cut corner on the upper right and the gold plate...
- 5. Lower the SIM card holder and press downward to lock the SIM card holder
- 6. Close the SIM card door
- 7. Install the battery
- Service
- ActiveSync (USB) Connectivity
- Troubleshooting
18
Direct Action Keys
The direct action keys enable the user a quick access to basic
operations of the HC700-G without exploring the HC700-G
software programs.
Screen Backlight Adjustment
The screen backlight can be adjusted by holding down the
<SHIFT> key and pressing the up or down bumps to
increase or decrease the screen backlight.
Turning the Screen Backlight On & Off
Hold down the <SHIFT> for two seconds - the screen back-
light will turn on. To turn off - hold down for another two sec-
onds.
When not in use, the backlight turns off automatically. To
configure the screen illumination duration, go to: Start Menu-
>Settings->System->Backlight.
Keypad Backlight Adjustment
The keypad backlight can be adjusted by holding down the
<SHIFT> key and pressing the right or left bumps to
increase or decrease the keypad backlight.
Turning the Keypad Backlight On & Off
Hold down the <SHIFT> key for four seconds - the keypad
backlight will turn on.
To turn off - hold down the <SHIFT> key for another two sec-
onds.
When not in use, the backlight turns off automatically. To
configure the keypad illumination duration, go to: Start
Menu->Settings->System->Backlight.
Calibrating the Touch Screen
To calibrate the touch screen - hold down the <SHIFT> and
<SP> and <C> keys and follow the calibrate application
instructions to complete your touch screen calibration.
Enhanced IMD Users.book Page 18 Thursday, February 9, 2006 11:52 AM