User's Manual
Table Of Contents
- COMPUTER SOFTWARE COPYRIGHTS
- Notational Conventions
- Welcome
- What is the HC700-G Handheld Computer?
- Unpacking
- HC700-G Features
- Charging the Battery
- Figure 3. HC700-G Personal Desktop Cradle
- Battery Replacement
- Figure 4. Battery Installation and Removal
- 1. Hold down the Power Button for at least four seconds until the HC700-G screen turns off.
- 2. Remove the HC700-G hand-strap (see Figure 4).
- 3. Press the battery snap on the battery (see Figure 4) and pull away the battery from the HC700-G.
- 4. Insert a fresh battery, bottom end first, into the battery compartment.
- 5. Carefully, press the battery top downward until it clicks and locks in place.
- 6. Press the Power Button - the HC700-G is now ready for use.
- First Time Battery Charge
- Routine Battery Charge
- Battery Maintenance
- Battery Disposal
- To Prevent Injury or Burns
- Using the HC700-G
- Starting to Work
- Turning On
- Turning Off
- Suspend Mode
- The Status LED
- The Application LED
- Making a Call
- Voice Recording
- Using the Keypad
- Direct Action Keys
- Scanning Barcodes and Capturing Images
- Figure 7. Capturing Images with the HC700-G Imager
- 1. Run the Bcr barcode reader application: Start Menu- >Programs->Sample Applications->Bcr.
- 2. Aim and hold the HC700-G at 2 to 12 inches (5 to 30 cm) distance from the target.
- 3. Press one of the Scan keys and aim the green aiming bar towards the target to adjust your posi...
- Resetting the HC700-G
- Mini SD Memory Card
- Installing a Mini SD Card
- Mini SD Card Handling Precautions
- SIM Card Installation
- Figure 12. SIM Card Installation
- 1. Remove the battery.
- 2. Open the SIM card door
- 3. Slide the SIM card holder forward to unlock the SIM card
- 4. Slide the new SIM card in the holder with the cut corner on the upper right and the gold plate...
- 5. Lower the SIM card holder and press downward to lock the SIM card holder
- 6. Close the SIM card door
- 7. Install the battery
- Service
- ActiveSync (USB) Connectivity
- Troubleshooting
15
Using the Keypad
The HC700-G keypad enables the user to enter both alpha-
betic and numeric data to the software application. However,
since the keypad can only contain a limited number of keys,
some special keys are assigned to perform special tasks that
are usually found on full-size computer keyboards. These are
produced using a combination of the existing keys on the
HC700-G keypad.
Two sets of keys exist on the HC700-G:
1. Keys active when in Alphabetic mode, which are those
seen on overlay of the HC700-G keypad.
2. Keys active when in Shift or Function mode which are
those seen next to each key on the HC700-G keypad
panel.
Press the
<SHIFT> key to toggle between the Alphabetic and
Numeric keypad modes. Figure 6 shows the HC700-G keypad
and Table 3 describes the HC700-G keys assignment.
S
M
G
B
Y
Z
X
R
L
F
C
D
E
H
I
A
J
K
N
O
P
Q
T
U
V
W
12
3
4
5
6
9
87
0
F2
F1
F4
F3
F5
F6
F7
F8
/
?
‘
;
!
@
&
$
F10
F9
F12
F11
^
%
-
+
,
.
*
#
TAB
ESC
Figure 6. HC700-G - Keypad
4-Way Navigation Key
Enter Key
Space Key
Backspace Key
End Key
Escape Key
Shift key
TAB/Send Key
Function Key
Main
Scan/Picture
Button
Application Key
Enhanced IMD Users.book Page 15 Thursday, February 9, 2006 11:52 AM