User's Manual
Table Of Contents
- COMPUTER SOFTWARE COPYRIGHTS
- Notational Conventions
- Welcome
- What is the HC700-G Handheld Computer?
- Unpacking
- HC700-G Features
- Charging the Battery
- Figure 3. HC700-G Personal Desktop Cradle
- Battery Replacement
- Figure 4. Battery Installation and Removal
- 1. Hold down the Power Button for at least four seconds until the HC700-G screen turns off.
- 2. Remove the HC700-G hand-strap (see Figure 4).
- 3. Press the battery snap on the battery (see Figure 4) and pull away the battery from the HC700-G.
- 4. Insert a fresh battery, bottom end first, into the battery compartment.
- 5. Carefully, press the battery top downward until it clicks and locks in place.
- 6. Press the Power Button - the HC700-G is now ready for use.
- First Time Battery Charge
- Routine Battery Charge
- Battery Maintenance
- Battery Disposal
- To Prevent Injury or Burns
- Using the HC700-G
- Starting to Work
- Turning On
- Turning Off
- Suspend Mode
- The Status LED
- The Application LED
- Making a Call
- Voice Recording
- Using the Keypad
- Direct Action Keys
- Scanning Barcodes and Capturing Images
- Figure 7. Capturing Images with the HC700-G Imager
- 1. Run the Bcr barcode reader application: Start Menu- >Programs->Sample Applications->Bcr.
- 2. Aim and hold the HC700-G at 2 to 12 inches (5 to 30 cm) distance from the target.
- 3. Press one of the Scan keys and aim the green aiming bar towards the target to adjust your posi...
- Resetting the HC700-G
- Mini SD Memory Card
- Installing a Mini SD Card
- Mini SD Card Handling Precautions
- SIM Card Installation
- Figure 12. SIM Card Installation
- 1. Remove the battery.
- 2. Open the SIM card door
- 3. Slide the SIM card holder forward to unlock the SIM card
- 4. Slide the new SIM card in the holder with the cut corner on the upper right and the gold plate...
- 5. Lower the SIM card holder and press downward to lock the SIM card holder
- 6. Close the SIM card door
- 7. Install the battery
- Service
- ActiveSync (USB) Connectivity
- Troubleshooting
7
Battery Replacement
When the battery
is drained, the
HC700 automati-
cally enters "Criti-
cal Low Battery"
state and shuts
down all functions
(the screen turns
off) to preserve the
data in its memory.
The HC700-G allows you to replace batteries without losing
information stored in its memory (“hot swap”). To avoid los-
ing data stored in the memory, a fresh battery must be
installed within five minutes after removing the drained bat-
tery.
To replace a battery perform the following steps:
1. Hold down the Power Button for at least four seconds
until the HC700-G screen turns off.
2. Remove the HC700-G hand-strap (see Figure 4).
3. Press the battery snap
on the battery (see Figure 4) and
pull away the battery from the HC700-G.
4. Insert a fresh battery, bottom end first, into the battery
compartment.
5. Carefully, press the battery top downward until it clicks
and locks in place.
6. Press the Power Button - the HC700-G is now ready for
use.
First Time Battery Charge
Charge the battery before using the HC700-G for the first
time until the status LED inside the Power Button shows
steady green. While charging for the first time, the Status
LED starts flashing orange and turns to steady read. When
battery is fully charged, the LED shows steady green.
The HC700-G Cradle charges the battery most effectively
when it is at room temperature [approx. 68°F (20°C)]. The rec-
Figure 4. Battery Installation and Removal
Hand-strap
Battery Snap
Battery
Compartment
Enhanced IMD Users.book Page 7 Thursday, February 9, 2006 11:52 AM