CB200-U CB200-M CB200-M User Guide User Guide
TABLE OF CONTENTS RF Safety & FCC............................................................................................................................... 4 Safety & Information........................................................................................................................5 Electromagnetic Interference Compliance.......................................................................................6 Industry Canada Compliance..................................................
TABLE OF CONTENTS LCD Contrast...................................................................................................................................... 20 User Defined Frequencies.................................................................................................................21 Software Version..............................................................................................................................22 Call Cycles................................................
RF SAFETY & FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
SAFETY & INFORMATION The CB200 requires care in mounting and servicing. Observing the following precautions will ensure the proper function and safety of the unit. CAUTION! • Do not screw through the device to mount to a surface. • Keep the Callbox away from water, high moisture, and high temperatures. • This equipment contains potentially hazardous voltages. • Do not attempt to disassemble the unit.
EMI COMPATIBILITY ELECTROMAGNETIC INTERFERENCE (EMI) COMPLIANCE NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. This device complies with part 15 of the FCC Rules and Industry Canada License-exempt RSS standard(s).
INDUSTRY CANADA COMPLIANCE Industry Canada (IC) statement (Canada) / Déclaration de Canada d’industrie (IC) (Canada) IC RF Exposure Statement / Déclaration d’exposition d’IC RF This device meets the IC requirements for RF exposure in public or uncontrolled environments. Cet appareil est conforme aux conditions de la IC en matière de RF dans des environnements publics ou incontrôlée. IC Warning / Avertissement d’IC This device complies with Industry Canada license exempt RSS standard(s).
COMPUTER SOFTWARE COPYRIGHTS The Motorola Solutions products described in this manual may include copyrighted Motorola Solutions computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola Solutions certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program.
DOCUMENTATION COPYRIGHTS 9 No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola Solutions. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola Solutions. DISCLAIMER The information in this document is carefully examined, and is believed to be entirely reliable.
INSTALLING THE BATTERIES BATTERY HOLDER The CB200 uses six (6) AA batteries. 1. Remove the battery holder from cardboard packaging. COPPER CONTACT 2. Orient the battery holder with the four copper contacts pointed towards you. 3. Insert the batteries following battery sled sticker. 4. Insert battery holder into bottom of device with the four contacts first. 5. Replace the battery holder cover.
CONTROL INTERFACE Available Controls and Components 1. Menu Button 2. Enter Button 3. Esc Button 4. Display 5. Microphone 6. Wake Up Button 7.
LCD DISPLAY 12 Initial Power-Up Once the batteries are installed in the unit, the Call Button blinks and LCD display shows Interface ENA. If the USB Serial Interface is not to be used, press the ESC button to exit this mode. The default status screen will be shown on the display. If nothing is pressed, the unit will enter sleep mode after 60 seconds and the screen will clear. Status Screen The Status Screen toggles the current Frequency and CTCSS setting continuously.
LCD WAKEUP The screen is in a blank “sleep” state during most operation, even when the system is operating. This is a feature to increase battery life and prevent tampering. To enter the Menu options, press the Wakeup button on the unit. The large round button blinks to indicate it is awake. The display remains disabled until any LCD menu control button is pressed. The LCD menu control buttons are Up or Down as shown in the following.
SCROLLING MENU You can setup preferred features on CB200 by scrolling through the menu options. Press the Menu buttons to scroll through menus. Menu options are presented in the order below, and the list repeats continuously.
RADIO FREQUENCY SELECTION Set Radio Frequency When the unit is awake and displaying the Status Screen, press the UP or Down Menu buttons until “Radio Freq?” appears. Press Enter Press Up or Down to select new frequency Press Enter to select new frequency Press Enter to select new frequency The CB200 is now programmed with the new frequency selected.
RADIO CODE SELECTION Set Code Frequency When the unit is awake and displaying the Status Screen, press the UP or Down Menu buttons until “Radio Code?” appears. Radio Code? Press Enter Old:12 100.0 Hz New:12 100.0 Hz Press Up or Down to select new code Old:12 100.0 Hz New:13 103.5 Hz Press Enter to select new code Old:12 100.Hz **Code Updated Press Enter to select new code The CB200 is now programmed with the new CTCSS code.
MESSAGE RECORDING Press Up or Down button until “Msg Record?” appears. Msg Record? Press Enter Select Message? Aux Message Press Up or Down to find message to record. Select Message? Local Message Press Enter to select message to record. Hold ENTER Btn To Record Msg Hold Enter button to record a new message. The new message automatically playback to verify it was recorded correctly. Message cannot be longer than 10 seconds.
MESSAGE PLAYBACK Press Up or Down button until “Msg Playback?” appears. Msg Playback? Press Enter Select Message? Local Message Press Up or Down to find message to playback. Select Message? Radio Message Press Enter to select message to playback. -Playback ActRadio Message Select new message to playback or press Esc to exit.
VOLUME ADJUSTMENT Press Up or Down button until “Volume Adjust?” appears. Volume Adjust? Press Enter Speaker Volume? Press Up or Down to select which volume to adjust, then press Enter. -Speaker VolVol(1-63): 45 Press Up or Down until desired volume selection is shown. The volume settings take place immediately. Press Esc to exit.
LCD CONTRAST Press Up or Down button until “LCD Contrast?” appears. LCD Contrast? -LCD Contrast(0-15): 0 Press Enter Press Up or Down until desired contrast selection is shown. The contrast settings take place immediately. Press Esc to exit. If the need arises to adjust the LCD contrast, check the batteries first. The batteries may be too weak to operate the unit correctly.
USER DEFINED FREQUENCIES If the radios you are using are set to frequencies not listed in our predefined set, you can reset them in this area. There are placeholders for 5 channels, UHF 57-61 ( VHF 6-10 ) ( Not Available in MURs ) Press Up or Down button until “User Def Freq?” appears. User Def Freq? Mem Location? (57-61):57 57 Old:467.8750 New:467.8750 Press Enter Press Up or Down to select which memory location to define. Press Up or Down to select new frequency. Press Enter.
SOFTWARE VERSION You may be asked by a field support or technical support personnel to determine the CB200 device’s software version. Press Up or Down button until “Software Ver?” appears.
CALL CYCLES Call Cycles refers to the repeating radio broadcasts that will occur when the call button is active. Press Up or Down button until “Call Cycles?” appears. Call Cycles? Press Enter Old: 2 cycles New: 2 cycles Press Up or Down to increase or decrease the Call Cycle selection. The range is 1-30 cycles. Press Enter to select the new Call Cycle.
CYCLE DELAY 24 Call Delay refers to the delay (in seconds) between repeating radio broadcasts that occur when the call button (or aux button) is active. Press Up or Down button until “Cycle Delay?” appears. Cycle Delay? Old: 45 sec New: 45 sec Press Enter Press Up or Down to increase or decrease the Cycle Delay selection. The range is 10-180 seconds. Press Enter to select the new Call Cycle.
INVERTED CODES When selecting digital CTCSS (squelch) codes, some receiving units may require inverted Octal numeric codes. Typically, receivers use the non-inverted codes. CB200-M is set to non-inverted by default. Note: This feature only applicable for CB200-M Press Up or Down button until “Inverted Codes?” appears. Press Enter Press Up or Down to select between NORMAL and INVERTED. Press Enter to select the new setting.
CHANGING VHF TO MURS The CB200-M can change between VHf channel set and MURs Channel Set. Note: This feature only applicable for CB200-M Press Up or Down button until “MURs or VHF?” appears. Press Enter Press Up or Down to cycle through MURS Only and VHF selections. Press Enter to select the new value or Esc to exit without any changes.
RF BUSY DELAY RF Busy Delay defines the amount of time after the CB200 recognizes an open channel before it makes it’s radio transmission. This is helpful if you would like to set a longer time between button press and radio message or to prevent transmitting while conversations are ongoing in some environments. Press Up or Down button until “RF Busy Delay?” appears. Press Enter Use the Up or Down to cycle through the RF Busy Delay selections (3-15 seconds).
MOUNTING THE DEVICE The CB200 can be mouted to the wall using the included 3M DualLock strips or by using the optional wall mounting bracket. Using 3M DualLock Ensure both the back of the callbox and the area of the surface that is being attached to is clean, flat, and dry. 1. Peel off one side of the DualLock’s release backing and firmly adhere to the left side of the unit. Repeat this with the other DualLock to the right side of the callbox. 2.
MOUNTING THE DEVICE 3. Once the callbox appears aligned, firmly press it to the wall in one motion. Note: The callbox is now removable by applying firm pressure around the exterior edge of the unit. For optional mounting accessories, please use the mounting bracket available from your Motorola CB200 distributor.
FREQUENCY SELECTION TABLE - UHF Freq. No. Freq. Value (MHz) Freq. No. Freq. Value (MHz) Freq. No. Freq. Value (MHz) 1 464.5000 13 461.1375 25 462.8125 2 464.5500 14 461.1625 26 462.8375 3 467.7625 15 461.1875 27 462.8625 4 467.8125 16 461.2125 28 462.8875 5 467.8500 17 461.2375 29 462.9125 6 467.8750 18 461.2625 30 464.4875 7 467.9000 19 461.2875 31 464.4875 8 467.9250 20 461.3125 32 464.5375 9 461.0375 21 461.3375 33 464.5625 10 461.
FREQUENCY SELECTION TABLE - UHF Freq. No. Freq. Value (MHz) Freq. No. Freq. Value (MHz) Freq. No. Freq. Value (MHz) 37 466.1125 49 467.8375 61 User Defined 38 466.1625 50 467.8625 39 466.1625 51 467.8875 40 466.1875 52 467.9125 41 466.2125 53 469.4875 42 466.2375 54 469.5125 43 466.2625 55 469.5375 44 466.2875 56 469.5625 45 466.3125 57 User Defined 46 466.3375 58 User Defined 47 466.3625 59 User Defined 48 467.
FREQUENCY SELECTION TABLE - VHF Freq. No. Freq. Value (MHz) Description 1 151.8200 Default Freq 2 151.8800 Default Freq 3 151.9400 Default Freq 4 154.5700 Default Freq 5 154.6000 Default Freq 6 154.6000 Custom Freq 1 7 154.6000 Custom Freq 2 8 154.6000 Custom Freq 3 9 154.6000 Custom Freq 4 10 154.
FREQUENCY SELECTION TABLE - MURS 33 Freq. No. Freq. Value Bandwidth (KHz) Description 1 154.5700 20 KHz Default Freq 2 154.6000 20 KHz Default Freq 3 151.8200 11.25 KHz Default Freq 4 151.8800 11.25 KHz Default Freq 5 151.9400 11.25 KHz Default Freq 6 154.5700 20 KHz Default Freq 7 154.
CTCSS CHART (ANALOG) 34 No. Code Hz No. Code Hz No. Code Hz No. Code Hz 1 67.0 13 103.5 25 156.7 37 241.8 2 71.9 14 107.2 26 162.2 38 250.3 3 74.4 15 110.9 27 167.9 4 77.0 16 114.8 28 173.8 5 79.7 17 118.8 29 179.9 6 82.5 18 123.0 30 186.2 7 85.4 19 127.3 31 192.8 8 88.5 20 131.8 32 203.5 9 91.5 21 136.5 33 210.7 10 94.8 22 141.3 34 218.1 11 97.4 23 146.2 35 225.7 12 100.0 24 151.4 36 233.
CTCSS CHART (DIGITAL) 35 No. Code No. Code No. Code No.
CTCSS CHART (DIGITAL) 36 No. Code No. Code No.
NOTES 37
NOTES
NOTES 39
Printed in USA 112217
