User Manual
Table Of Contents
- Cover2
- MN003432A01_aa.pdf
- CHAPTER 1 : FOREWORD
- CHAPTER 2 : WIRELESS RSM PMMN4096_
- PREPARING YOUR WRSM FOR USE
- Assembling the Swivel Clip
- Attaching the Battery
- Detaching the Battery
- Charging the Battery
- Language Selection
- Recommended Wearing Positions
- IDENTIFYING WRSM INDICATORS AND CONTROLS
- Overview of the WRSM
- Power Indicators and Battery Alerts
- Audio Indicators
- GENERAL WRSM OPERATION
- Powering ON/OFF the WRSM
- Volume Control
- Pairing Your WRSM
- Subsequent Connection
- Poor Signal / Out Of Range Warning Indication
- Push-to-Talk (PTT) Button
- Programmable Button (Orange Button)
- Tasklight Button
- Dark Mode
- Secondary Receiver Audio Accessory
- Failure Detected Indication and Handling
- Troubleshooting
- Firmware Upgrade
- NOTES
- CHAPTER 3 : DUAL-UNIT CHARGER PMLN6714_
- PREPARING YOUR DUC FOR USE
- Operational Guidelines
- Motorola Authorized Battery
- Motorola Authorized Power Sources/Power Supplies
- Overview of the DUC
- Operating Instructions
- a Aligning the groove on each side of the battery with the corresponding raised rail on each side of the charger pocket.
- b Sliding the WRSM with battery into the charger pocket, ensuring complete contact between the charger and battery contacts.
- 4 When the WRSM with battery is properly seated in the pocket, the charger LED will light in accordance with Table 3.3.
- a Aligning the slot on each side of the battery with the corresponding raised rail on each side of the charger pocket.
- b Sliding the battery into the charger pocket, ensuring complete contact between the charger and battery contacts.
- 6 When the battery is properly seated in the pocket, the charger LED will light in accordance with Table 3.3.
- LED Light Indication
- Troubleshooting
- CHAPTER 4 : VEHICULAR CHARGER PMLN6716_
- PREPARING YOUR VEHICULAR CHARGER FOR USE
- Operational Guidelines
- Operating Specifications
- Motorola-Authorized Battery
- Overview of Vehicular Charger
- Installation
- Operating Instructions
- Figure 4.3: Removing Vehicular Charger from Mounting Bracket
- Figure 4.4: Placing and Removing the Vehicular Charger from the Mounting Bracket
- Placing and Removing the WRSM or Battery to and from the Vehicular Charger
- a Aligning the groove on each side of the battery with the corresponding raised rail on each side of the charger pocket per Figure (R1).
- b Pressing on the front – top surface of the WRSM according to the direction indicated in Figure (R2) to lock the WRSM into Vehicular Charger.
- a Aligning the groove on each side of the battery with the corresponding raised rail on each side of the charger pocket per Figure (B1).
- b Pressing on the front – top surface of the battery according to the direction indicated in Figure (B2) to lock the battery into Vehicular Charger.
- a Pressing on the Vehicular Charge’s release button to unlatch the battery per Figure (R3).
- b Remove the WRSM from the pocket by sliding the WRSM upward per Figure (R2).
- a Pressing on the Vehicular Charge’s release button to unlatch the battery per Figure (B3).
- b Remove the battery from the pocket by sliding the battery upward per Figure (B2).
- LED Light Indication
- Troubleshooting
- CHAPTER 5 : REPLACEABLE PARTS
- CHAPTER 6 : OPEN SOURCE SOFTWARE LEGAL NOTICE
- CHAPTER 7 : SERVICE AND SUPPORT
- CHAPTER 9 : WARRANTY
- Limited Warranty
- A Defects or damage resulting from use of the Product in other that its normal and customary manner.
- B Defects or damage from misuse, accident, water, or neglect.
- C Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.
- D A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with M...
- E Product which has had the serial number removed or made illegible.
- F Freight costs to the repair depot.
- G A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time t...
- H Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product.
- I Normal and customary wear and teat.
- A That MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;
- B That MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and
- C Should the Product or parts become, or in MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to produce for such pu...
- NOTES
- Limited Warranty
- BackCover
FOREWORD
English
vi
WAVE 5000 MOBILE CLIENT AND RADIO
CONFIGURATION
By default, the WRSM is compatible with the radio ONLY. To work with
WAVE 5000 Mobile Client, choose WAVE 5000 on Operation Mode at
Accessory Programming Software (APS).
WAVE5000 Mobile Client Android Application Package (APK) version
TBD and above must be used for compatibility with the WRSM. This can
be configured using the APS tool.
The APS tool allows you to select two modes of operation:
• Radio mode – configuring the WRSM to be used with your radio.
Refer to Table 1.2 for radios compatible to the WRSM.
• Wave5k mode – configuring the WRSM to be used with the Wave
5000 Mobile Client on a smartphone.