User Manual
Table Of Contents
- Cover2
- MN003432A01_aa.pdf
- CHAPTER 1 : FOREWORD
- CHAPTER 2 : WIRELESS RSM PMMN4096_
- PREPARING YOUR WRSM FOR USE
- Assembling the Swivel Clip
- Attaching the Battery
- Detaching the Battery
- Charging the Battery
- Language Selection
- Recommended Wearing Positions
- IDENTIFYING WRSM INDICATORS AND CONTROLS
- Overview of the WRSM
- Power Indicators and Battery Alerts
- Audio Indicators
- GENERAL WRSM OPERATION
- Powering ON/OFF the WRSM
- Volume Control
- Pairing Your WRSM
- Subsequent Connection
- Poor Signal / Out Of Range Warning Indication
- Push-to-Talk (PTT) Button
- Programmable Button (Orange Button)
- Tasklight Button
- Dark Mode
- Secondary Receiver Audio Accessory
- Failure Detected Indication and Handling
- Troubleshooting
- Firmware Upgrade
- NOTES
- CHAPTER 3 : DUAL-UNIT CHARGER PMLN6714_
- PREPARING YOUR DUC FOR USE
- Operational Guidelines
- Motorola Authorized Battery
- Motorola Authorized Power Sources/Power Supplies
- Overview of the DUC
- Operating Instructions
- a Aligning the groove on each side of the battery with the corresponding raised rail on each side of the charger pocket.
- b Sliding the WRSM with battery into the charger pocket, ensuring complete contact between the charger and battery contacts.
- 4 When the WRSM with battery is properly seated in the pocket, the charger LED will light in accordance with Table 3.3.
- a Aligning the slot on each side of the battery with the corresponding raised rail on each side of the charger pocket.
- b Sliding the battery into the charger pocket, ensuring complete contact between the charger and battery contacts.
- 6 When the battery is properly seated in the pocket, the charger LED will light in accordance with Table 3.3.
- LED Light Indication
- Troubleshooting
- CHAPTER 4 : VEHICULAR CHARGER PMLN6716_
- PREPARING YOUR VEHICULAR CHARGER FOR USE
- Operational Guidelines
- Operating Specifications
- Motorola-Authorized Battery
- Overview of Vehicular Charger
- Installation
- Operating Instructions
- Figure 4.3: Removing Vehicular Charger from Mounting Bracket
- Figure 4.4: Placing and Removing the Vehicular Charger from the Mounting Bracket
- Placing and Removing the WRSM or Battery to and from the Vehicular Charger
- a Aligning the groove on each side of the battery with the corresponding raised rail on each side of the charger pocket per Figure (R1).
- b Pressing on the front – top surface of the WRSM according to the direction indicated in Figure (R2) to lock the WRSM into Vehicular Charger.
- a Aligning the groove on each side of the battery with the corresponding raised rail on each side of the charger pocket per Figure (B1).
- b Pressing on the front – top surface of the battery according to the direction indicated in Figure (B2) to lock the battery into Vehicular Charger.
- a Pressing on the Vehicular Charge’s release button to unlatch the battery per Figure (R3).
- b Remove the WRSM from the pocket by sliding the WRSM upward per Figure (R2).
- a Pressing on the Vehicular Charge’s release button to unlatch the battery per Figure (B3).
- b Remove the battery from the pocket by sliding the battery upward per Figure (B2).
- LED Light Indication
- Troubleshooting
- CHAPTER 5 : REPLACEABLE PARTS
- CHAPTER 6 : OPEN SOURCE SOFTWARE LEGAL NOTICE
- CHAPTER 7 : SERVICE AND SUPPORT
- CHAPTER 9 : WARRANTY
- Limited Warranty
- A Defects or damage resulting from use of the Product in other that its normal and customary manner.
- B Defects or damage from misuse, accident, water, or neglect.
- C Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.
- D A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with M...
- E Product which has had the serial number removed or made illegible.
- F Freight costs to the repair depot.
- G A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time t...
- H Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product.
- I Normal and customary wear and teat.
- A That MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;
- B That MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and
- C Should the Product or parts become, or in MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to produce for such pu...
- NOTES
- Limited Warranty
- BackCover
VEHICULAR CHARGER PMLN6716_
English
23
Overview of Vehicular Charger
Figure 4.1: Overview of the Vehicular Charger
Installation
Install Mounting Bracket (HLN9073_)
Refer to Figure 4.2 below and attach hang-up clip (1) to vehicle using
two sheet metal screws and back-up plate provided. Place back-up
plate (4) behind dashboard. Use flat-head screw (2) in top mounting
hole and hex-washer screw (3) in bottom mounting hole. Be certain
mounting screws fasten into holes in back-up plate.
Figure 4.2: Installing the Mounting Bracket
Release Button
1
2
Warning Label /
LED Indication
Charging Contact
3
Rotating Pocket
4
LED
5
Cigarette Light
Adapter (CLA)
6
8
Product Label
Vehicle
Dashboard
1
2
3
4