ACCESSORIES WIRELESS RSM FOR PORTABLES SOLUTIONS USER GUIDE PMMN4096 WIRELESS REMOTE SPEAKER MICROPHONE PMLN6714 DUAL-UNIT CHARGER PMLN6716 VEHICULAR CHARGER PMNN4461 WIRELESS REMOTE SPEAKER MICROPHONE BATTERY en-US fr-CA es-LA pt-BR ko-KR de-DE fr-FR it-IT nl-NL pt-PT ru-RU uk-UA es-ES
BackCover.
CHAPTER 1: FOREWORD RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios ATTENTION! This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations.
Consignes de sécurité importantes Radios bidirectionnelles portatives : exposition aux radiofréquences et sécurité du produit ATTENTION! Cette radio ne doit être utilisée qu'à des fins professionnelles.
Battery Information: Battery is shipped with a nominal charge between 30% and 50%. Battery should be stored between -10 °C (14 °F) and 30 °C (86 °F) to minimize permanent capacity loss. CAUTION: Storing your fully charged accessory in high-temperature conditions may permanently reduce the life of the internal battery. FOREWORD Important Information: • Hold the microphone in a vertical position with the microphone at least one inch (2.5 centimeters) away from the nose or lips. • Body Worn Operation.
WARNINGS Table 1.1: Motorola Authorized Battery ! 3. To reduce risk of damage to the electric plug and cord of the DUC, pull by the plug rather than the cord when disconnecting the charger. 4. To reduce risk of damage to the CLA and cord of the Vehicular Charger, pull by the CLA rather than the cord when disconnecting the charger. 5. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in risk of fire and electric shock.
Vehicular Charger PMLN6716_ RADIO COMPATIBILITY • Equipment shall be used in vehicle and in dry condition. Keep in mind that rain or snow can reach the equipment i.e. through an open vehicle window. The Wireless Remote Speaker Microphone (WRSM) is compatible with • Ensure the WRSM with attached battery or battery alone is dry before inserting into the Vehicular Charger. • Connect equipment only to an appropriately vehicle’s cigar lighter socket of the correct voltage (as specified on the product).
WAVE 5000 MOBILE CLIENT AND RADIO CONFIGURATION WAVE5000 Mobile Client Android Application Package (APK) version TBD and above must be used for compatibility with the WRSM. This can be configured using the APS tool. The APS tool allows you to select two modes of operation: • Radio mode – configuring the WRSM to be used with your radio. Refer to Table 1.2 for radios compatible to the WRSM. • Wave5k mode – configuring the WRSM to be used with the Wave 5000 Mobile Client on a smartphone.
PREPARING YOUR WRSM FOR USE Assemble your WRSM by following these steps: Assembling the Swivel Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2 Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2 Detaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3 Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3 Language Selection . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the Battery Insert the swivel clip through the battery slot. Rotate the clip to the right position as indicated in Figure 2.1 below. With the WRSM turned off, align the battery to back chassis and fully slot in until the battery latch is engaged. WIRELESS RSM PMMN4096_ Assembling the Swivel Clip 2 English 1 2 1 2 Figure 2.1: Assembling the swivel clip Figure 2.
Charging the Battery To detach the battery, lift up the battery latch and pull the battery backward until the battery is fully disengaged from the back chassis. Ready >90% CAUTION LED STATUS INDICATOR Charging Standby S Unable to C harge RISK OF FIRE. REFER TO MANUAL FOR BATTERY TYPE 1 2 WIRELESS RSM PMMN4096_ Detaching the Battery Figure 2.4: Charging position of the WRSM with battery attached Figure 2.
Language Selection WIRELESS RSM PMMN4096_ To avoid a possible explosion: ! • DO NOT replace the battery in any area labeled “hazardous atmosphere”. Follow the procedure below if you want to reset to your desired language. Ensure that the WRSM is powered OFF before starting this procedure. WARNING • DO NOT discard batteries in a fire. Procedure: The Motorola-approved battery shipped with your WRSM is uncharged.
For optimum performance, wear the WRSM as highlighted in Figure 2.6 below. 1 Power Button / Multi Function Button (MFB) 2 Push-to-Talk (PTT) Button Figure 2.5: Language Selection WIRELESS RSM PMMN4096_ Recommended Wearing Positions Figure 2.6: Recommended wearing positions NOTE: When the WRSM is worn on the body, always use Motorolaapproved clip.
IDENTIFYING WRSM INDICATORS AND CONTROLS Take a moment to review the following: WIRELESS RSM PMMN4096_ Overview of the WRSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6 Power Indicators and Battery Alerts . . . . . . . . . . . . . . . . . . . . . page 7 Audio Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Indicators The WRSM is battery powered. It is very important to pay attention to the low battery warning described in Table 2.2 to avoid improper functioning of the WRSM. Table 2.2: Power Indicators and Battery Alerts State Power Indication LED Normal Battery Tone Indication Remaining Battery Life No tone 11 hours (full charged) – 30 minutes Green Low Battery Low Battery tone every 2 minutes Less than 30 minutes Low Battery tone every 30 seconds Less than 10 minutes Table 2.
WIRELESS RSM PMMN4096_ GENERAL WRSM OPERATION Powering ON/OFF the WRSM Once you understand how your WRSM is configured, you are ready to use your WRSM. Use this navigation guide to familiarize yourself with the basic features: To power ON the WRSM, press and hold the Power Button until you hear “Motorola Solutions” prompt. To power OFF, press the Power Button until the WRSM turns off. Powering ON/OFF the WRSM . . . . . . . . . . . . . . . . . . . . . . . . . page 8 Volume Control . . . . . . . . . . .
Pairing Your WRSM To increase the volume, push volume lever towards the the volume, push lever towards the To mute, hold lever to the the . To decrease . Procedure: 1 Verify that both the host and the WRSM are powered ON (First time only: Once the WRSM is powered ON, if not previously selected, the WRSM will instruct the user to select language or tone, and then it goes into Pairing Mode automatically.).
Subsequent Connection Poor Signal / Out Of Range Warning Indication WIRELESS RSM PMMN4096_ Same Host: If the Bluetooth link is lost, connection will be automatically reestablished when the host and device come within 10 meter range (line-of-sight). You will be prompted with the Poor Signal / Ouf Of Range Warning Indication if the WRSM is about to lose the wireless link at Bluetooth fringe area. New Host: This warning indication will turn off if the user moves closer or if the signal quality improves.
Tasklight Button Press and hold down the PTT button to talk. Release the PTT button to listen. The microphone is activated when the PTT button is pressed. Press the Tasklight Button for 1 second to switch ON/OFF the tasklight. During low/critical battery, the Tasklight blinks for 30 seconds and will be auto switched OFF. NOTE: The Tasklight is disabled when WRSM is in Dark Mode. Dark Mode Dark Mode allows you to turn OFF the LEDs on the WRSM.
Secondary Receiver Audio Accessory Table 2.
Table 2.8: Optional Accessories Part Number Description RLN4941_ Earpiece with Coiled Cord and 3.5 mm RT Angle Plug RLN4885_ Receiver Earbud for Remote Speaker Microphone Firmware upgrade is available for this WRSM and it is only upgradeable by your dealer. Check with your dealer for more information on the latest firmware upgrades. NOTE: DO NOT charge the WRSM with this micro USB port, it is strictly for firmware upgrade only. NOTE: Some part numbers may have regional prefix such as AA, MD or AZ.
WIRELESS RSM PMMN4096_ NOTES 14 English
PREPARING YOUR DUC FOR USE Take a moment to review the following: Operational Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 24 Motorola Authorized Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . page 24 Motorola Authorized Power Sources/Power Supplies . . . . . . . page 24 Overview of the DUC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 25 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operational Guidelines DUAL-UNIT CHARGER PMLN6714_ • • Always remember to power ON the Dual-Unit Charger first before inserting the WRSM with the attached battery or battery alone into the pocket. The Dual-Unit Charger is designed to provide simultaneous charging for both pockets. Motorola Authorized Battery The battery listed in Table 3.1 is approved for use with the Dual-Unit Charger. Table 3.
LEDs Pocket Barrel Connector Figure 3.1: Dual-Unit Charger (Front View) DUAL-UNIT CHARGER PMLN6714_ Overview of the DUC Figure 3.
Operating Instructions DUAL-UNIT CHARGER PMLN6714_ Dual-Unit Chargers are intended for use only with the authorized Motorola battery and power supplies listed in Table 3.1 and Table 3.2; usage with unauthorized products may prevent proper operation and may damage the device. The battery charger will accommodate a WRSM with an attached battery or battery alone in either pocket.
Table 3.3: Charger Status (Continued) When troubleshooting, always observe the color of the LED. Table 3.
Troubleshooting DUAL-UNIT CHARGER PMLN6714_ If There is Fast Flash Red Indication: 1 Confirm the battery being used with the WRSM is listed in Table 3.1 and is good in condition. 2 Confirm that the power supply being used with the WRSM is listed in Table 3.2 and is good in condition. 3 Remove the battery and restart the Dual-Unit Charger. 4 If the symptom persist, please send the Dual-Unit Charger to the nearest Service Center for further verification.
PREPARING YOUR VEHICULAR CHARGER FOR USE Take a moment to review the following: Operational Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 30 Operating Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 30 Motorola-Authorized Battery . . . . . . . . . . . . . . . . . . . . . . . . . . page 30 Overview of Vehicular Charger . . . . . . . . . . . . . . . . . . . . . . . . page 31 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VEHICULAR CHARGER PMLN6716_ Operational Guidelines Motorola-Authorized Battery • Always remember to plug in the CLA first before inserting the WRSM with the attached battery or battery alone into the pocket. The battery listed in Table 4.1 is approved for use with the Vehicular Charger. • • The Vehicular Charger is designed to be portable. The WRSM is designed to be functional even when charging takes place. Operating Specifications Vehicular Charger Input voltage range: 10.8 Vdc to 33.
Installation Install Mounting Bracket (HLN9073_) 1 Release Button 2 Warning Label / LED Indication 3 Charging Contact 4 Rotating Pocket 5 LED Refer to Figure 4.2 below and attach hang-up clip (1) to vehicle using two sheet metal screws and back-up plate provided. Place back-up plate (4) behind dashboard. Use flat-head screw (2) in top mounting hole and hex-washer screw (3) in bottom mounting hole. Be certain mounting screws fasten into holes in back-up plate.
VEHICULAR CHARGER PMLN6716_ Table 4.2: Mounting Brackets Description 24 English Item Motorola Part Number Description 1 0180757T98 Hang-up Clip 2 0312002C01 Flat-Head Screw 3 0312002A01 Hex-Washer Head Screw 4 0780257N01 Back-up Plate Operating Instructions Vehicular Chargers are intended for use only with the authorized Motorola battery listed in Table 4.1 ; usage with unauthorized products may prevent proper operation and may damage the device.
2 Rotate 90° 4 3 Slide out Slide in Insertion Removal Figure 4.4: Placing and Removing the Vehicular Charger from the Mounting Bracket 2 Slide out the cradle as per step (4). VEHICULAR CHARGER PMLN6716_ 1 Mount the Charger 1 Slide in the stud onto the bracket as per step (1). Remove the Charger 1 Rotate the cradle horizontally (90 °) as per step (2) & (3).
Placing and Removing the WRSM or Battery to 3 VEHICULAR CHARGER PMLN6716_ and from the Vehicular Charger When the battery is properly seated in the pocket, the charger’s LED will light in accordance with Table 4.3 per Figure (B3). Placing the WRSM or Battery to the Vehicular Charger Removing the WRSM or Battery from the Vehicular Charger The Vehicular Charger will accommodate a WRSM with an attached battery or battery alone in pocket.
2 1 3 Press Press Slide in Slide out Figure (R1) LED ON Figure (R2) Insertion Figure (R3) VEHICULAR CHARGER PMLN6716_ Attach and Remove WRSM Removal Figure 4.
Attach and Remove Battery 2 1 3 VEHICULAR CHARGER PMLN6716_ Press Press Slide in Slide out LED ON Figure (B1) Figure (B2) Insertion Removal Figure 4.
LED Light Indication The Vehicular Charger will accommodate for both swivel clips: • • Standard swivel clip (PMLN6743_) – Any rotational position D-ring swivel clip (42009312001) – Horizontal position Rotate D-ring swivel clip to horizontal position before inserting the WRSM or battery into the Vehicular Charger. When troubleshooting, always observe the color of the LED. Table 4.
Table 4.3: Charging Status (Continued) VEHICULAR CHARGER PMLN6716_ Fast Flash Red 30 English Off Battery under voltage recovery time out OR Loss of charge current control OR Excessive power supply voltage OR Fault connection happened – DO NOT charge battery If battery is inserted into a successfully powered up charger, battery may have bad contact with charger Troubleshooting If There is Fast Flash Red Indication: 1 Confirm the battery being used with the WRSM is listed in Table 4.
CHAPTER 5: REPLACEABLE PARTS Part Number Description Other than the replaceable parts listed below, the PMMN4096_, PMLN6714_ and PMLN6716_ are not repairable. 25012022009 Power Supply, Charger Switch Mode, 110 – 240 V KOR HLN9073_ Microphone Hang-up Clip KT-SB1XLANYD3 Standard Lanyard with Velcro The following parts are available: Table 5.
REPLACEABLE PARTS NOTES 32 English
This Motorola Solutions Product contains Open Source Software. For information regarding licenses, acknowledgments, required copyright notices and other usage terms, refer to the documentation for this Motorola Solutions Product at: https://businessonline.motorolasolutions.
OPEN SOURCE SOFTWARE LEGAL NOTICE NOTES 34 English
DO NOT disassemble the PMMN4096_, PMLN6714_ and PMLN6716_; they are not repairable. Order replacement parts listed in “REPLACEABLE PARTS" on page 41. Please contact Motorola Solutions Customer Care as shown in Table 7.1 below for ordering or any technical troubleshooting assistance. Table 7.
SERVICE AND SUPPORT NOTES 36 English
Contact your Motorola Solutions dealer for detailed information on the standard warranty. The workmanship warranty guarantees against defects in workmanship under normal use and service. NOTE: Warranty is void after customer replacement of any parts other than replacement parts listed. Table 9.
II. GENERAL PROVISIONS: This warranty sets forth the full extent of MOTOROLA’S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY.
MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end use purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following: A That MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim; B T
WARRANTY NOTES 40 English
BackCover.
BackCover.fm Page 2 Wednesday, November 9, 2016 11:11 AM m MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2016 Motorola Solutions, Inc. All rights reserved.
