User Manual
Table Of Contents
- Contents
- List of Figures
- List of Tables
- Copyrights
- General Information
- Getting Started
- Product Technical Information
- Before Power On
- Controls and Indicators
- Display
- Status Icons
- Powering On the Radio
- Unlocking Your Radio
- Locking/Unlocking the Keys/Buttons
- Holding Your Radio
- Entering TMO / DMO Mode
- Transmit Inhibit Mode
- Selecting Talkgroups
- Talkgroup Icon Selection
- Activating Talkgroup Scanning
- Broadcast Call
- Ambience Listening (AL) Call
- One-Touch Button Feature
- Terminal Temporary Disable/Enable
- Terminal Permanent Disable
- High/Low Audio Toggle
- During the Call
- Writing Text
- Home Display Text Message
- Modes
- Using Networks
- Trunked Mode Operation
- Entering TMO Mode
- Selecting Talkgroups
- Making Group Calls in TMO
- Receiving Group Calls in Idle
- Receiving Group Calls during Ongoing Group Calls
- Dynamic Group Number Assignment (DGNA)
- DGNA Reception
- DGNA Auto Select Group
- DGNA Auto Reselect Group
- Viewing DGNA Talkgroups
- Broadcast Calls Initiated by Users
- Initializing Broadcast Calls
- Phone and PABX Calls
- Private Call
- Making Private Calls
- Assistance Call
- Call Modification
- Local Site Trunking
- Direct Mode Operation
- Transmit Inhibit Mode
- Emergency Operations
- Emergency Group Call
- Making Emergency Group Calls
- Receiving Emergency Group Calls
- Non-Tactical Emergency
- Emergency Individual Calls (Private or MS-ISDN)
- Emergency Alarm
- Emergency SDS Status
- Emergency Hot Microphone
- Alternating Hot Microphone
- Silent Emergency Mode
- Invisible Emergency
- Disaster Alert
- Initializing Disaster Alert Calls
- Exiting Emergency Operations
- Repeater Mode
- GPS Location Service
- Main Menu
- Scrolling through the Menu
- Menu Icons
- Messages
- Contacts
- Bluetooth
- Browser
- Security
- Setup
- Group Setup
- Favorites
- My Info
- Recent Calls
- Shortcuts
- Networks
- Location
- Packet Data
- Crypto Menu
- Features
- Private Call
- Radio Messaging System (RMS)
- One-Touch Dial
- Talkgroup Dialing by Index
- Phone and PABX Calls
- Phone/PABX Speed Dial
- MS-ISDN
- Short Number Dial
- RUA/RUI
- WAP
- Call-Out
- Appendix A: Tones
- Appendix B: LED Indications
- Appendix C: Troubleshooting
- Appendix D: Maintenance
Receiving Emergency Group Calls
The radio receives an Emergency Group Call from a selected pre-programmed group. An incoming call
is indicated by an appropriate tone, status icon, and red color of the display.
Non-Tactical Emergency
In Non-Tactical Emergency, the radio switches to a designated Emergency talkgroup when starting
Emergency Operations. This talkgroup is used for the complete duration of the Emergency Operations
(you cannot change the talkgroup).
In TMO, it is possible to configure the radio to make Emergency Non-Tactical Group Calls without
sending attachment. If this is set, the radio assumes implicit attachment after receiving a temporary
address.
In DMO, the Non-Tactical Emergency proceeds on the same frequency as the previously selected
talkgroup. The service provider can designate any ITSI address to be used for Emergency Operations,
(this can be an Open Group – broadcast address).
After exiting from Non-Tactical Emergency, the radio goes back to the previously selected talkgroup.
Emergency Individual Calls (Private or MS-ISDN)
The Emergency Individual Calls are Simplex or Duplex Calls with emergency priority. On pressing the
EMERGENCY button, the radio initiates an Individual Call to the provisioned address (private or MS-
ISDN). During this kind of call all user indications are unavailable and all other services are rejected.
Emergency Operation ends as soon as the Emergency Individual Call is ended.
Related Links
Private Call on page 50
MS-ISDN on page 119
Emergency Alarm
The Emergency Alarm is a special status message sent to the infrastructure while starting the
Emergency Operations. The radio can wait for infrastructure acknowledgment for this alarm and
attempts retries.
Each time the radio enters the Emergency Operation, it sends the Emergency Alarm. When the
Emergency Alarm is sent successfully, the respective audible tone sounds.
In addition, once the radio is in the Emergency Operation on pressing the EMERGENCY button, an
additional emergency alarm is sent (exception: during Hot Microphone transmission).
The message can be dispatched both in TMO and DMO.
Emergency SDS Status
Radio sends a status message with a preprogrammed value to the destination address set by your
service provider. Emergency SDS Status is available in TMO only. If no status acknowledgment or
negative acknowledgment is received, the radio retries sending the message. Status is not resend if
Emergency Alarm or Hot Microphone is configured.
Emergency Hot Microphone
The Hot Microphone allows you to talk without pressing the PTT button during Emergency Operations.
The transmission continues for a provisioned amount of time. Pressing the PTT button before the Hot
Microphone time expires ends the Hot Microphone operation. Then normal PTT operation in
Chapter 3: Modes
58 Send Feedback