User Manual
Table Of Contents
- Contents
- List of Figures
- List of Tables
- Copyrights
- General Information
- Getting Started
- Product Technical Information
- Before Power On
- Controls and Indicators
- Display
- Status Icons
- Powering On the Radio
- Unlocking Your Radio
- Locking/Unlocking the Keys/Buttons
- Holding Your Radio
- Entering TMO / DMO Mode
- Transmit Inhibit Mode
- Selecting Talkgroups
- Talkgroup Icon Selection
- Activating Talkgroup Scanning
- Broadcast Call
- Ambience Listening (AL) Call
- One-Touch Button Feature
- Terminal Temporary Disable/Enable
- Terminal Permanent Disable
- High/Low Audio Toggle
- During the Call
- Writing Text
- Home Display Text Message
- Modes
- Using Networks
- Trunked Mode Operation
- Entering TMO Mode
- Selecting Talkgroups
- Making Group Calls in TMO
- Receiving Group Calls in Idle
- Receiving Group Calls during Ongoing Group Calls
- Dynamic Group Number Assignment (DGNA)
- DGNA Reception
- DGNA Auto Select Group
- DGNA Auto Reselect Group
- Viewing DGNA Talkgroups
- Broadcast Calls Initiated by Users
- Initializing Broadcast Calls
- Phone and PABX Calls
- Private Call
- Making Private Calls
- Assistance Call
- Call Modification
- Local Site Trunking
- Direct Mode Operation
- Transmit Inhibit Mode
- Emergency Operations
- Emergency Group Call
- Making Emergency Group Calls
- Receiving Emergency Group Calls
- Non-Tactical Emergency
- Emergency Individual Calls (Private or MS-ISDN)
- Emergency Alarm
- Emergency SDS Status
- Emergency Hot Microphone
- Alternating Hot Microphone
- Silent Emergency Mode
- Invisible Emergency
- Disaster Alert
- Initializing Disaster Alert Calls
- Exiting Emergency Operations
- Repeater Mode
- GPS Location Service
- Main Menu
- Scrolling through the Menu
- Menu Icons
- Messages
- Contacts
- Bluetooth
- Browser
- Security
- Setup
- Group Setup
- Favorites
- My Info
- Recent Calls
- Shortcuts
- Networks
- Location
- Packet Data
- Crypto Menu
- Features
- Private Call
- Radio Messaging System (RMS)
- One-Touch Dial
- Talkgroup Dialing by Index
- Phone and PABX Calls
- Phone/PABX Speed Dial
- MS-ISDN
- Short Number Dial
- RUA/RUI
- WAP
- Call-Out
- Appendix A: Tones
- Appendix B: LED Indications
- Appendix C: Troubleshooting
- Appendix D: Maintenance
NOTICE: If the Rotary Mode is set to:
• Dual or Volume — Display shows Auto Selected (OTB), volume can be set only
through VOLUME KNOB.
• Scroll — Display shows Auto Selected (Volume), volume can be set only
through SIDE buttons.
• Volume Adjust. — Sets the SIDE buttons to adjust volume level.
• OTB Feature — Sets the SIDE buttons to the predefined One-Touch Button features.
Group Setup
This sub-menu allows you to set the operation parameters, scanning and my groups folder.
Standard Home Group
This menu item allows you to configure the standard home group to be used during start up and when
changing modes: TMO –> DMO and TMO –> Repeater.
Related Links
Operations Parameters on page 102
Operations Parameters
When and where to use: If you want to define the radio mode and the talkgroup at the radio startup,
and when changing modes TMO->DMO and TMO-> Repeater.
Procedure:
1 From the home screen, press the MENU key.
2 Select Group Setup → Operations Parameters.
3 Select Startup. Select one of the following:
• TMO – the radio powers up in TMO mode.
• DMO – the radio powers up in DMO mode.
• Last Selected – the radio powers up in the mode it was in when last powered down.
4 Select Home Group Startup. Select one of the following:
• Last Selected – the radio enters the TMO/DMO talkgroup which was last selected before
power down.
• Home Group – the radio enters the Home Group (TMO or DMO) at power up, depending on
the radio mode entered at power up.
5 Select HGr TMO->DMO/Rep. Select one of the following:
• Last Selected – when changing modes the radio enters the DMO Talkgroup last selected,
i.e. the DMO Talk Group active last time the Radio was in DMO Mode. If Group Mappings
are configured, they will take precedence and the DMO Talkgroup mapped to the current
TMO Talkgroup is used.
• Group Mappings – when changing modes the radio enters the DMO Home Group unless a
Group Mapping is configured. If Group Mappings are configured, they will take precedence
and the DMO Talkgroup mapped to the current TMO Talkgroup is used.
• Home Group – when changing modes the radio enters the DMO Home Group, ignoring
possible group mappings.
Chapter 5: Main Menu
102 Send Feedback