Motorola iDEN Digital Multi-service Data-capable Phone i530 Phone User’s Guide SECOND DRAFT @NNTN4881A@ NNTN4881A
Contents Getting Started .............................................. 1 Locating Your SIM Card....................................... 3 Battery.................................................................. 3 Activating Service ................................................ 6 Powering On ........................................................ 6 Enabling Over-the-Air Security ............................ 7 Finding Your Phone Number ............................... 7 Completing Setup ..................
Forwarding Missed Calls.................................... 38 Viewing Call Forwarding Settings ...................... 39 Messages ..................................................... 41 Message Notifications........................................ 41 Voice Mail .......................................................... 41 Text and Numeric Messages ............................. 42 Net Alerts ........................................................... 43 Ring Tones.........................................
3-Way Calling..................................................... 70 Creating Pauses and Waits While Dialing ......... 71 Making International Calls.................................. 71 Setting One Touch PTT ..................................... 71 Setting Flip Actions ............................................ 72 Group Calls........................................................ 72 Call Timers......................................................... 73 Using Your Phone as a Modem.......................
iv
DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola, Inc. Address: 8000 West Sunrise Boulevard Plantation, FL 33322 USA Phone Number: 1 (800) 453-0920 Hereby declares that the product: Product Name: i530 Model Number: H63XAH6RR3AN Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
vi
Getting Started earpiece display screen p Power button. Navigation key — press the arrows to scroll through menus and lists. volume controls navigation key Push-To-Talk (PTT) button punctuation key back/pause dialing key accessory connector space key microphone m Accesses context-sensitive menus. A Selects the option appearing above it on the display. s Places phone calls. e Ends phone calls; returns to idle screen.
Getting Started speaker hi/lo/audio cover 2 antenna smart key . Acts like e when the phone cover is closed; accesses recent calls. t Acts like swhen the phone cover is closed; turns speakerphone on; used with voice names and voice records.
Locating Your SIM Card Locating Your SIM Card Battery Your SIM (Subscriber Identity Module) card is a small piece of white plastic located in the SIM card holder in the back of your phone, underneath the battery. Removing the Battery Door SIM card 1 Make sure the phone is powered off. 2 Slide the release button back until it releases the battery door. SIM card holder 3 Allow the battery door to pop up and remove it from the back of your phone.
Getting Started Inserting the Battery Charging the Battery 1 With the phone powered off, remove the battery door. 2 Insert the top of the battery into the battery area. Press the bottom of the battery to secure it. Your phone comes with a battery charger. 1 Plug the charger into an electrical outlet. 2 Open the connector cover. connector cover 3 Replace the battery door and press it gently until you hear a click. 4 3 Plug the other end of the charger into the accessory connector.
Battery Tip: To remove the charger from the accessory connector: Press the buttons on the sides of the plug. Pull the plug straight out. 2 Remove the battery by pushing the battery toward the antenna and lifting it out. 4 When charging the battery for the first time, charge for 30 minutes longer than the time shown in “Charging Times”. Charging Times See your battery and charger to determine the appropriate charging time.
Getting Started Activating Service The first time you power on your phone, you must be in your local calling area. This activates your service. Powering On As your phone connects to the network, you will see a welcome message and a connecting message. When the idle screen appears, the phone is ready to use. s 1 d The first time you power your phone on, screen may appear asking you to update your browser information. This means you must enable security.
Enabling Over-the-Air Security Enabling Over-the-Air Security If you are set up to receive over-the-air programming from your service provider, you must enable security the first time you power on your phone or within 20 days of first activation of your phone: 1 When you power on your phone for the first time, after the idle screen appears, you will be prompted to select Ok to update your browser information.
Getting Started • Carrier IP — the IP address assigned to your service provider. It is filled in when you register for packet data services. • IP1 Address and IP2 Address — the IP addresses you use to access the Internet with your phone • Ckt — Your circuit data number is the number you use if you want to use your phone to transfer circuit data. See “Using Your Phone as a Modem” on page 74. You receive this number from your service provider.
Phone Basics Phone Basics Menus and Lists Any time your phone is powered on, the display provides you with information and options. Your phone’s features are arranged in menus, submenus, and lists. s 1 d status icons text area menu icon display options Contcs S Mesg The screen shown above is the idle screen. The text that appears on your idle screen depends on your service provider. The idle screen appears when your phone is on, but not engaged in any activity.
Getting Started Main Menu g Memo All your phone’s features can be accessed through the main menu. When you are using a feature, the icon for that feature appears in the upper left corner of the display. Store a number to access later. See page 67. h Call Timers Phone usage information. See page 73. a Browser Browse the Web. b Settings Display/Info Phone Calls 2-Way Radio Volume Security Advanced Customize your phone. See page 81. c VoiceRecord Record and play audio messages. See page 63.
SIM Card Security Status Icons Status icons appear in the 2 rows at the top of the display. Some appear at all times. Others appear only when your phone is engaged in certain activities or when you have activated certain features. ab cd Battery Strength — More bars on the battery indicate a greater charge. ef gd o p q Signal Strength — More bars next to the r s antenna indicate a stronger signal. A Phone In Use — Your phone is active on a phone call.
Getting Started Entering the PIN You may be required to enter a SIM PIN when you first use your phone. When you receive your phone, the SIM PIN is 0000. Change your PIN to prevent fraudulent use of the SIM card. Important: If you enter your PIN incorrectly 3 times, your SIM card is blocked. To unblock your SIM card, you must contact your service provider. See “Unblocking the PIN” on page 13. 1 When the Enter SIM PIN Code screen appears, enter your SIM PIN. An asterisk appears for each character entered.
SIM Card Security Unblocking the PIN If you enter your PIN incorrectly 3 times, your SIM card is blocked. To unblock your SIM card, you must contact your service provider to get a PIN Unblock Code (PUK). Important: If you unsuccessfully enter the PUK code 10 times, your SIM card is permanently blocked and must be replaced. If this happens, all data is lost. You will get a message to contact your service provider. Except for making emergency calls, your phone will not function with a blocked SIM card.
Getting Started 7 Hold your SIM card as shown. Do not touch the gold-colored area. 2 While holding down the tab near the SIM card holder, slide your SIM card out of the SIM card holder. Do not touch the gold-colored area. SIM card holder cut corner tab 8 Carefully slide your SIM card into your phone, until it lies flat in the SIM card holder. SIM card holder Note: Protect your SIM card as you would any delicate object. Store it carefully.
Accessories To lock the keypad: 1 From the idle screen, press m. 2 Press *. If you press a key while the keypad is locked, instructions for unlocking the keypad display briefly. To unlock the keypad: 1 From the idle screen, press m. 2 Press *. While the keypad is locked, you can respond to incoming calls, messages, and alerts just as you do when the keypad is not locked. When finished, press e to return to the idle screen. The keypad remains locked.
Getting Started 16
Making Calls Your i530 phone makes 2 types of calls: digital cellular phone calls and Private calls. With Private calls, you use your phone as a long-range, digital walkie-talkie. To make a phone call: 1 Enter the number you want to call. 2 To place the call: 3 Release the PTT button to listen. Tip: To let someone know you want to talk to him or her on a Private call, send a call alert. See “Call Alerts” on page 23.
Making Calls To end a phone call: Press e. -orClose the flip. -orIf the flip is closed, press .. When you receive a Private call, your phone emits a chirping sound. To answer a Private call: 1 Wait for the caller to finish speaking. 2 Press and hold the PTT button on the side of your phone. Begin talking after your phone emits a chirping sound. 3 Release the PTT button to listen. Call Icons When you make a call, call icons appear in the text area of the phone’s display.
Entering the Number to Call • To insert or delete a digit anywhere in the string of digits you have entered, scroll left or right. • To cancel, press e. From the Recent Calls List The recent calls list stores the last 20 calls you made or received. To select a number from the recent calls list as the number you want to call: With the Flip Open 1 From the idle screen, scroll down. -orFrom the main menu, select Recent Calls. 2 Scroll to the name or number you want to call. With the Flip Closed 1 Press .
Making Calls 3 Press A under View. -orIf View is not one of your options: Press m. Select View. 4 Place the call now. -orScroll to view more numbers. When you place the call, it is made to the number displayed. Redialing the Last Number If you are making a Private call, press and hold the PTT button to place the call. If you are making a phone call, the call is placed automatically. Tip: To stop a phone call from being completed, press . if the flip is closed or press e.
Missed Phone Calls Using One Touch PTT To dismiss the missed call message: One Touch PTT sets your phone to call the most recent Private ID on the recent calls list, or to a Private ID you choose, every time you press the PTT button. See “Setting One Touch PTT” on page 71. To display the most recent call: From Datebook You can now call the most recent call, or view the rest of the recent call list. See page 19.
Making Calls Opening the flip turns speakerphone off. Using Mute Muting calls lets you listen to incoming sound without transmitting sound. Mute is available whenever you are on an active call. To turn mute on: Press A under Mute. While mute is on, Unmute appears as a display option. To turn mute off: Press A under Unmute. Making Emergency Phone Calls Your phone supports emergency calling. Emergency phone calls can be made even when your SIM card is blocked or not in your phone.
Call Alerts Receiving Call Alerts Sending a call alert lets the recipient know you want to talk to him or her on a Private call. When you receive a call alert, you must answer, queue, or clear it. You cannot receive phone calls or Private calls until you do. When you send a call alert, the recipient’s phone emits a series of beeps and displays your name or Private ID.
Call Alerts 1 From the main menu, select Call Alert. 2 Scroll through the list. 3 Press A under Alert. Ready to Alert appears on the display. 4 Press the PTT button until Alert Successful appears on the display. Viewing Date and Time Deleting Call Alerts To view the date and time a call alert was received: To delete a call alert from the queue: 1 2 3 4 1 From the call alert queue, scroll to the call alert you want to delete. 2 Press m. 3 Select Delete. 4 Press A under Yes to confirm.
Using the Call Alert Queue 5 Press A under Select.
Call Alerts 26
Recent Calls The recent calls list stores the numbers of the 20 most recent calls you have made and received. If the number of a recent call is stored in Contacts, the name associated with the number appears on the recent calls list. An icon appears beside the name or number indicating the Contacts type of the number used in the call. See “Contacts” on page 27. For phone calls, an icon appears to the left of the name or number giving more information about the call: X A call you made.
Recent Calls If Store is not one of your options: Press m. Select Store. Tip: If Store is not on this menu, the number is already stored in Contacts. 3 To store the number as a new entry, select [New Contact]. -orTo store the number to an existing entry, select the entry. 4 With the Contacts type field highlighted, scroll left or right to display the Contacts type you want to assign the number. For information on Contacts types, see page 29.
Contacts • A Contacts type — Each number or address stored must be assigned a Contacts type: Contacts stores up to 600 numbers or addresses. Each Contacts entry can store several numbers or addresses. A Mobile phone number B Private Private ID Information stored in Contacts is saved on your SIM card. C Work1 phone number A Contacts entry contains: D Work2 phone number • A name — A name is required if your are storing more than one number or address to the entry; otherwise, it is optional.
Contacts • A Speed Dial number — When you store a phone number, it is assigned a Speed Dial number. You can accept the default Speed Dial number or change it. • A voice name — If you create a voice name for a number, you can then dial that number by saying the voice name into your phone. This icon appears P to the left of the Contacts type icon if a voice name is assigned. Note: This is an optional feature. Contact your service provider about its availability for purchase.
Creating Entries 3 With Show Prvt/Grp highlighted, press A under Select. To set Contacts to show all entries: 1 2 3 4 From the Contacts list, press m. Select Filter. Scroll to Show All. Press A under Select. Creating Entries A number or address and a Contacts type are required for all Contacts entries. Other information is optional. You may enter the information in any order by scrolling through the entry details.
Contacts Enter the number or address. For phone numbers, use the 10-digit format. For email addresses, see “Entering Text” on page 77. Tip: Press A under Browse to select a number or address from Contacts, the recent calls list, or Memo. When you are finished, press A under Ok. 6 If you want to assign more options to the number, press A under Change with the [Options] field highlighted. See “Assigning Options” on page 32.
Editing Entries To store numbers to Contacts from the idle screen: 1 Use the keypad to enter the number you want to store. 2 Press m. 3 Select Store Number. 4 To store the number as a new entry, select [New Contact]. -orTo store the number to an existing entry, select the entry. 5 With the Contacts type field highlighted, scroll left or right to display the Contacts type you want to assign the number.
Contacts 4 Press A under Yes to confirm. Checking Capacity If you want a pause longer than 3 seconds, press and hold * more than once. Each P represents a 3-second pause. To see how many numbers are stored in Contacts: To program a wait: 1 From the Contacts list, press m. 2 Select Capacity. Creating Pauses and Waits When storing a number, you can program your phone to pause or wait between digits while dialing. A pause makes your phone pause for 3 seconds before dialing further.
Accessing Contacts with GSM Phones 2 Enter the country code, city code or area code, and phone number. For information about making international calls, see “Making International Calls” on page 71. Accessing Contacts with GSM Phones If you plan to use the information stored in Contacts with an i2000, i2000plus, or any other GSM phone, you must purchase CompanionPro. Go to www.motorola.com/idenupdate or your service provider’s web site for more information.
Contacts 36
Call Forwarding Call forwarding sends calls to the phone numbers you specify. You can forward all calls to one number or forward missed calls to different numbers depending on the reason you missed the call. You can forward phone lines 1 and 2 independently. Forwarding All Calls To forward all calls: 1 2 3 4 5 6 From the main menu, select Call Forward. Press A under Change. Select All Calls. Scroll to To. Press A under Change.
Call Forwarding Turning Off Call Forwarding If you don’t want all your calls forwarded, turn the feature off: 1 2 3 4 5 6 7 From the main menu, select Call Forward. Press A under Change. Select All Calls. Scroll to To. Press A under Change. Scroll to Off. Press A under Select. All your calls are now sent to your phone. Calls you miss are forwarded according to the options set for missed calls. By default, missed calls are forwarded to voice mail.
Viewing Call Forwarding Settings Press A under Search. Select Contacts, Recent Calls, or Memo. Select the number you want to enter. 8 Press A under Ok. 9 Repeat step 4 through step 8 for No Answer and If Unreachable. When you are finished, press A under Back. Viewing Call Forwarding Settings 1 From the main menu, select Call Forward. 2 With To highlighted, press m. 3 Select Retrieve Status.
Call Forwarding 40
Messages To access your voice mail messages, text and numeric messages, Net alerts, and any other types of messages you are able to receive, go to the message center: 1 Press A under Mesg. -orFrom the main menu, select Messages. 2 Scroll to the type of message you want to access. 3 Press A under the display option on the left. The message center shows how many messages you have of each type. You can listen to, read, or delete these messages.
Messages When you receive a voice mail message, New Voice Mail Message appears on the display. To call your service provider’s voice mail system and listen to the message: Press A under Call. To dismiss the message notification: If the phone cover is closed, press . or open the phone cover. The phone’s display refers to text and numeric messages as Text Messages. These messages can be up to 140 letters or 20 digits long. You can store up to 16 of these messages.
Net Alerts 3 To keep the message, press A under Save. -orTo delete the message, press A under Delete. To dismiss the message notification: Press A under Back. This icon w appears on the display, reminding you that you have a new message. When you receive a Net alert, a notification appears on the display. If you dismiss the notification, this icon w appears on the display, reminding you that you have a new message. Reading from the Message Center 1 2 3 4 From the message center, select Text Msgs.
Messages 44
Ring Tones Using the Vibrate Feature To set the ring tone your phone makes when you receive phone calls, message notifications, or call alerts: If your phone includes a vibrate feature, you can set your phone to vibrate when you receive phone calls, Private calls and group calls, messages notifications, or call alerts. 1 From the main menu, select Ring Tones. 2 Make sure VibeAll or SilentAll is set to Off. 3 Scroll through the list of ring tones to the one you want to assign.
Ring Tones Never Ring 1 From the main menu, select Ring Tones > SilentAll. 2 Scroll left or right to set SilentAll to On. Always Vibrate Instead of Ringing 1 From the main menu, select Ring Tones > VibeAll. 2 Scroll left or right to set VibeAll to On. Tip: Pressing the volume controls to turn down the volume as far as possible sets VibeAll to On.
Viewing Ring Tone Assignments 3 Scroll through the list of ring tones to the one you want to assign. Highlighting a ring tone lets you hear it. 4 Press A under Assign. 5 Select A Contact. 6 Scroll to the Contacts entry you want to assign the ring tone to. 7 Press A under Select. Viewing Ring Tone Assignments 1 2 3 4 5 From the main menu, select Ring Tones. Make sure VibeAll or SilentAll is set to Off. Highlight any ring tone. Press m. Select Overview.
Ring Tones Deleting Custom Ring Tones To delete a custom ring tone: 1 2 3 4 5 6 48 From the main menu, select Ring Tones. Make sure VibeAll or SilentAll is set to Off. Scroll to the ring tone you want to delete. Press m. Select Delete. Press A under Yes to confirm.
Mobile Originated Text Messaging With mobile originated text messaging, you can send and receive short text messages to and from other iDEN phones. Messages you receive appear on your phone’s display and in the text message inbox. You access these messages through the message center. See “Messages” on page 41. Note: This feature may not be offered by your service provider.
Mobile Originated Text Messaging Reading Messages From the Message Center 1 From the main menu, select Message > Text Inbox. 2 Scroll to the message you want to read. 3 Press A under Read. 4 If the message fills more than one screen, scroll to read it. 5 To keep the message, press A under Save. -orTo delete the message, press A under Delete. Tip: To see more choices, including replying to the message, press m. Your text inbox holds up to 16 messages. Each message can be up to 160 characters long.
Creating and Sending Messages 7 If you want to specify the type of message you want to send: With the Send As field highlighted, press A under Change. Scroll to the message type you want. Press A under Select. 8 To send the message: Press s. Press A under Yes. -orTo save the message as a draft without sending it: Press m. Scroll to Save As Draft. Press A under Select. -orTo delete the message without sending it: Press m. Scroll to Delete. Press A under Select.
Mobile Originated Text Messaging Enter text. See “Entering Text” on page 77. -orTo choose from pre-installed notes: Press A under Browse. Scroll to the note you want. Press A under Select. 3 Press A under Store. Tip: For more options, including sending the quick note, press m. 3 Follow step 3 through step 7 in “Creating and Sending Messages” on page 50. 4 Scroll to Save As Draft. Using the Outbox Messages you have sent are stored in the outbox.
Managing Memory 3 Press m. 4 Select Re-send. 5 Press A under Yes to confirm. 3 Press m. 4 Scroll to Lock to lock the message. -or- Deleting Sent Messages 5 Press A under Select. To delete a sent message: Managing Memory 1 From the main menu, select Messages > Text Outbox. 2 Scroll to the message you want to delete. 3 Press m. 4 Select Delete. 5 Press A under Yes to confirm. To delete all unlocked sent messages: 1 From the main menu, select Messages > Text Outbox. 2 Press m. 3 Select Delete All.
Mobile Originated Text Messaging 2 Press m. 3 Select Memory Meter.
GPS Enabled Your phone’s GPS Enabled feature uses information from Global Positioning System (GPS) satellites orbiting the Earth to determine the approximate geographical location of your phone, expressed as latitude and longitude. The availability and accuracy of this location information (and the amount of time that it takes to calculate it) will vary depending on the environment in which you are using the GPS feature.
GPS Enabled Walking or driving very slowly may also substantially reduce GPS performance. Even where location information can be calculated in such situations, it may take much longer to do so, and your location estimate may not be as accurate. Therefore, in any 911 call, always report the location to the emergency response center if you can and if you cannot, remain on your phone for as long as the emergency response center instructs you.
Viewing Your Approximate Location reduced access to satellite signals. When your approximate location is determined, it is made available to the appropriate emergency response center. In some cases, your local 911 emergency response center may not be equipped to receive GPS location information.
GPS Enabled It may take your phone several minutes to complete the process of determining your location. During this time, a message usually appears on your phone’s display saying your phone is scanning for satellites. For tips on getting the best location calculation, see “Enhancing GPS Performance” on page 58. The Position screen displays the updated information. To cancel a location calculation before it is completed: Press A under Cancel to return to the Position screen.
Updating Satellite Almanac Data service provider’s name on it. Hold your phone away from your body, giving the antenna clear access to satellite signals. Do not cover the antenna area with your fingers or anything else. GPS antenna area Note: Although moving your phone at a walking pace decreases GPS performance, moving it at the speed of a moving car does not. • Stay in network coverage.
GPS Enabled Note: When you make an emergency call, your phone does not rely upon the almanac to determine your location. If your satellite almanac data is out of date, your phone may prompt you to update it. Follow the instructions that appear on the phone’s display. You may be asked to go to a web site or call a customer care number. Setting Privacy Options Your phone’s GPS privacy options control whether software applications may view the location of your phone.
Using GPS with Map Software Note: When you receive your phone, your GPS PIN is 0000. 5 Press A under Ok. To change your GPS PIN: 1 From the main menu, select Settings > Security > Change Password > GPS PIN. 2 Enter the current GPS PIN. Note: When you receive your phone, your GPS PIN is 0000. 3 4 5 6 7 Press A under Ok. Enter the new 4- to 8-digit GPS PIN. Press A under Ok. Enter the new 4- to 8-digit GPS PIN to confirm. Press A under Ok.
GPS Enabled Getting Started To connect your phone to your laptop or other device: 1 Open the connector cover. Make sure no other application is using the COM port selected. Make sure the COM port settings of your laptop or other device are set to the following: • • • • • connector cover 2 With the phone’s display facing up, insert the data cable’s connector into the accessory connector, until you hear a click.
Voice Records Note: This is an optional feature. Contact your service provider about its availability for purchase. A voice record is a recording you make with your phone and can play back. You can record notes to yourself or phone calls. Your phone can store up to 20 voice records, with a total time of 3 minutes or more, depending on available memory. 5 Press A under Select. Say the message you want to add into the microphone. 6 When you are finished recording, press A under Stop.
Voice Records Labelling Voice Records 4 Press A under Yes to confirm. When you create a voice record, it is labeled with the time and date it was recorded. You can then rename it with a custom label. Locking Voice Records 1 2 3 4 5 From the main menu, select VoiceRecd. Scroll to the voice record you want to label. Press m. Select Label. Enter the label you want to assign. See “Entering Text” on page 77. 6 Press A under Ok.
Managing Memory 2 3 4 5 Press m. Select Memory. Press A under Delete. Press A under Yes to confirm. Note: Voice records are stored in your phone using the same memory space used to store ring tones (see “Ring Tones” on page 45), Deleting ring tones frees memory space for voice records.
Voice Records 66
Memo Memo lets you store a number, make a call to that number, and save it to Contacts. To create a memo: 1 From the main menu, select Memo. 2 Enter the number using your keypad. 3 Press A under Store. To view the memo later: 1 From the main menu, select Memo. To delete the memo: 1 From the main menu, select Memo. 2 Press and hold A under Delete. 3 Press A under Store. To store the memo number to Contacts: 1 2 3 4 From the main menu, select Memo. Press m. Press A under Select.
Memo 68
Advanced Calling Features Call Waiting Call Waiting lets you receive a second call while on an active call. Call Waiting is always available, unless you turn it off for a specific call. Switching Between Calls When you accept a second call, the display shows the name or number of each call, with an icon indicating which call is active: Y Phone call is active. Z Phone call is on hold.
Advanced Calling Features To turn off Call Waiting for the next call you make or receive: To end the second call and make the call on hold active again: 1 From the main menu, select Settings > Phone Calls > Call Waiting. 2 Press A under Change. 3 Scroll to Off. 4 Press A under Select. To make the call on hold active and put the active call on hold: Call Waiting is turned back on when you end the call. 3-Way Calling Press e. Press A under Switch.
Creating Pauses and Waits While Dialing 9 Press A under Select. Both calls are now active and appear on the display. Creating Pauses and Waits While Dialing You can enter a pause or wait while dialing a number. For more information on pauses and waits, see “Creating Pauses and Waits” on page 34. To create a pause while dialing a phone number: 1 From the keypad, enter the digits you want to occur before the pause. 2 Press m. 3 Select Insert Pause. 4 Enter the digits you want to occur after the pause.
Advanced Calling Features To set your phone to call a Private ID you choose: 2 Set this option to On. 1 From the main menu, select Settings > 2-Way Radio > One Touch PTT > Assigned Number. 2 To enter the Private ID you want your phone to call every time you press the PTT button: To set your phone not to answer calls when you open the flip: Enter the number using your keypad. -orPress A under Search. Select Contacts, Recent Calls, or Memo. Select the number you want to enter.
Call Timers Before you can make or receive group calls, a Talkgroup must be established. After the Talkgroup is established, you must join the Talkgroup. See “Joining a Talkgroup” on page 8. To set your phone to let you hear group calls to your Talkgroup: Making Group Calls Call Timers 1 Press #. Then enter the Talkgroup number using the keypad.
Advanced Calling Features • Kbytes Reset — keeps a running total of the number of Kilobytes sent and received by your phone, until you reset it. 1 Open the connector cover. To view or reset a timer: 1 From the main menu, select Call Timers. 2 Select the feature you want to view or reset. 3 To view a feature without resetting: Press A under Done when you are finished viewing. -orTo reset a feature: Press A under Reset. Press A under Yes to confirm.
Making TTY Calls • Circuit data — used for sending and receiving faxes and for transferring large files • Packet data — used for small file transfers such as email When you make a TTY call, these icons appear on the phone’s display: N Phone call is active. O Phone call is on hold. To use these services, you must install the iDEN Wireless Data Services software (available separately).
Advanced Calling Features To change mode while not in a call: Changing the TTY Baud Rate 1 From the main menu, select Settings > Phone Calls > TTY > Type. 2 Press A under Change. 3 Scroll to the TTY mode you want. 4 Press A under Select. By default, your phone’s TTY baud rate is set to 45.45, the baud rate required for TTY calls within the U.S. To make calls outside the U.S., set your TTY baud rate to 50.0. When you make a TTY call, the call begins in the TTY mode you last selected.
Entering Text You can enter text into your phone using the traditional method of pressing a key several times for each character, or by pressing a key once for each letter while words likely to be the one you want are chosen from a database. You can also enter symbols and numbers into a text field. In screens that require you to enter text, you see the following icons near the top right corner. These icons tell you which text input mode you are using: l Alpha — Press a key several times for each character.
Entering Text 2 Type a word by pressing one key for each letter. For example, to type “test” press 8 3 7 8. The displayed word may change as you type it. Do not try to correct the word as you go. Type to the end of the word before editing. 3 If the word that appears is not the desired word, press 0 to change the word on the display to the next most likely word in the database. Repeat until the desired word appears. If the desired word does not appear, you can add it to the database.
Using Numeric Mode Punctuation Press 1 or 0 to insert punctuation. Continue to press the key to view the list of symbols available through that key. Pause to select the symbol you want. Note: Additional punctuation symbols are available in Symbols mode. Using Numeric Mode 1 Select Numeric as your text input mode. 2 Press the number buttons on your keypad to enter numbers. Using Symbols Mode 1 Select Symbols as your text input mode. A row of symbols appears along the bottom of your phone’s display.
Entering Text 80
Customizing Your Phone Setting the Volume To set the volume of the sound coming from the phone’s earpiece or speaker: 1 From the main menu, select Settings > Volume. 2 Scroll to Earpiece to set the earpiece volume. -orScroll to Speaker to set the speaker volume. 3 Press A under Change. 4 To select the volume: Scroll left or right. -orPress the volume controls. 5 Press A under Ok. To set the volume of the phone’s ring: Press the volume controls.
Customizing Your Phone 2 Press A under Change. 3 Scroll left or right to set the contrast. 4 Press A under Ok. Using a Headset If you use a headset or similar device with your phone, you can set your phone to send incoming sound to the headset only, or to the headset and the speaker at the same time: 1 From the main menu, select Settings > Advanced > Headset/Spker. 2 Press A under Change. 3 Scroll to HdsetOnly to send incoming sound to the headset only.
Using Settings • Minute Beep — causes a beep to sound every minute of an active call. • Call Duration — causes the duration of a call to appear on the phones display when the call ends. • TTY — lets you use your phone with a TTY device. See “Making TTY Calls” on page 75. • Notifications — See “Setting Notification Options” on page 41.
Customizing Your Phone • SIM PIN — enables and disables your phone’s SIM PIN security feature. See “Turning the PIN Requirement On and Off” on page 12. • GPS PIN — enables and disables your phone’s GPS PIN security feature. See “Setting the GPS PIN Security Feature” on page 60. • Change Passwords — changes your phone unlock code, security code, SIM PIN, and GPS PIN. Advanced Features The Advanced menu contains advanced and rarely used Settings features.
Understanding Status Messages Status Messages Message Description System Busy The system is experiencing heavy traffic. Please try again later. You may receive status messages under certain conditions. Before contacting Customer Care, note the message, numeric code, and the conditions under which it appeared. The following table lists and describes the status messages. Please Try Again An error occurred. Please try again. Self Check Error + Number Code A fault was detected with your phone.
Understanding Status Messages Status Messages Message Description Enter SIM PIN Please enter your 4- to 8- digit SIM PIN code. Enter Unlock Code Auto Phone Lock is activated. Enter you unlock code. New Browser Message Memory Full! Warns of low memory for Net Alerts. Scanning for Satellites Searching for GPS satellites. Unable to Locate Sats Could not find GPS satellites. Technical Error A problem occurred in your phone’s GPS circuitry.
Safety and General Information Portable Radio Product Operation and EME Exposure • United States Federal Communications Commission, Code of Federal Regulations; 47 CFR part 2 sub-part J. • American National Standards Institute (ANSI) / Institute of Electrical and Electronics Engineers (IEEE). C95. 1-1992. • Institute of Electrical and Electronics Engineers (IEEE). C95. 1-1999 Edition. • International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998. • Ministry of Health (Canada).
Safety and General Information When placing or receiving a phone call, hold your radio product as you would a wireline telephone. Speak directly into the microphone. • Phone or Two-way radio mode: one inch (2.5 cm) • Data operation using any data feature with or without an accessory cable: one inch (2.5 cm) Two-way radio operation Antenna Care When using your radio product as a traditional two-way radio, hold the radio product in a vertical position with the microphone one to two inches (2.
Portable Radio Product Operation and EME Exposure ALL MODELS WITH FCC ID AZ489FT5825 MEET THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
Safety and General Information Electro Magnetic Interference/Compatibility Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. Medical Devices Pacemakers The Advanced Medical Technology Association (AdvaMed) recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio product and a pacemaker.
Operational Warnings Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Use While Driving Check the laws and regulations on the use of radio products in the area where you drive. Always obey them. When using the radio product while driving, please: • Give full attention to driving and to the road.
Safety and General Information other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are often but not always posted. Blasting Caps and Areas To avoid possible interference with blasting operations, turn off your radio product when you are near electrical blasting caps, in a blasting area, or in areas posted: “Turn off two-way radio”. Obey all signs and instructions.
Accessory Safety Information Clean the external surfaces of the radio product with a damp cloth, using a mild solution of dishwashing detergent and water. Some household cleaners may contain chemicals that could seriously damage the radio product. Avoid the use of any petroleum-based solvent cleaners. Also, avoid applying liquids directly on the radio product. Accessory Safety Information Important: Save these accessory safety instructions.
Safety and General Information • The cord size is 18AWG for lengths up to 100 feet and 16AWG for lengths up to 150 feet. • Do not operate any battery charger if it has received a sharp blow, has been dropped, or has been damaged in any way; take it to a qualified service technician. • Do not disassemble a battery charger; take it to a qualified service technician when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
MOTOROLA LIMITED WARRANTY Note: FOR IDEN SUBSCRIBER PRODUCTS, ACCESSORIES AND SOFTWARE PURCHASED IN THE UNITED STATES OR CANADA PRODUCTS COVERED LENGTH OF COVERAGE Products as defined above. One (1) year from the date of purchase by the first consumer purchaser of the product. What Does this Warranty Cover? Subject to the exclusions contained below, Motorola, Inc.
What is not covered? (Exclusions) Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage. Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty. Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.
MOTOROLA LIMITED WARRANTY Software NOT Embodied in Physical Media. Software that is not embodied in physical media (e.g. software that is downloaded from the internet), is provided "as is" and without warranty. Who is covered? This warranty extends only to the first consumer purchaser, and is not transferable. What will Motorola Do? Motorola, at its option, will at no charge repair, replace or refund the purchase price of any Products, Accessories or Software that does not conform to this warranty.
BUSINESS, LOSS OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS, ACCESSORIES OR SOFTWARE TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW. Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you.
MOTOROLA LIMITED WARRANTY Limited Warranty Motorola Communication Products (International) Note: This Warranty applies in Singapore and the Philippines. I.
Limited Warranty Motorola Communication Products (International) equipment if expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole, or any portion of the system not produced by MOTOROLA, under this warranty. II.
MOTOROLA LIMITED WARRANTY d. e. f. g. h. i. j. operation, maintenance, installation, alteration, modification, or adjustment. Breakage or damage to antennas unless caused directly by defects in material workmanship. A Product subjected to unauthorized Product modifications, disassemblies or repairs (including, without limitation, the audition to the Product of non-MOTOROLA supplied equipment). Product which has had the serial number removed or made illegible. Rechargeable batteries if: 1.
Limited Warranty Motorola Communication Products (International) option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.
Patent and Trademark Information MOTOROLA, the Stylized M Logo and all other trademarks indicated as such herein are trademarks of Motorola, Inc. ® Reg. U.S. Pat. & Tm. Off. © 2003 Motorola, Inc. All rights reserved. Microsoft and Microsoft Internet Explorer are registered trademarks of Microsoft Corporation. T9 is a trademark owned by Tegic Communications. T9® Text Input Patent and Trademark Information This product is covered by U.S. Pat. 5,818,437, U.S. Pat. 5,953,541, U.S. Pat.
Patent and Trademark Information 104
Index Numerics 2-way radio 83 see also Private calls, group calls, and call alerts 3-way calling 70 A Accessories 15 safety 93 Alpha mode 77 B Backlight 82 Battery care 5 charging 4, 5 cover 3 inserting 4 safety 92 Baud rate 84 C Call alerts 23 deleting 24 queue 23 receiving 23 responding 23, 24 sending 23 sorting 24 viewing 24 Call forwarding 37 all calls 37 missed calls 38 off 38 Call Hold 70 Call Timers 73 Call Waiting 69 off 69 Calls 3-way 70 answering automatically 82 answering with any key 82 emer
Index International numbers 34 searching 30 showing all entries 31 showing only Private IDs 30 SIM card 29 storing fast 32 storing from idle screen 33 storing from Memo 32, 67 storing from recent calls 27, 32 type 27, 29 viewing 30 voice name 32 with non-i205 phones 35 D Datebook 21 Display backlight 82 contrast 81 options 9 screen 9 E Email 29, 32, 75 receiving 43 sending 43 106 Emergency calls 22 End key 1 F Faxes receiving 75 sending 75 Flip action 72 G GPS Enabled 55 almanac data 59 best results 58
Lists, see menus M Memo 67 calling from 67 creating 67 editing 67 storing to Contacts 32, 67 viewing 67 Memory mobile originated text messaging 53 ring tones 47 voice records 64 Menu key 1, 9 Menus 9 context-sensitive 1, 9 main menu 10 Message notifications 41 setting options 41 Messages 41 see also mobile originated text messaging reading 43 receiving 41 text and numeric 42 Mobile originated text messaging 49 creating messages 50 deleting 53 drafts 52 icons 52 memory 53 outbox 52 quick notes 51 reading m
Index deleting 28 display time 84 icons 27 storing to Contacts 27, 32 viewing 27 Redialing 20, 82 Ring tones 29, 45 deleting 48 downloading 47 memory 47 off 45 setting 45 setting in Contacts 31, 46 silent 45, 46 vibrate 45, 46 viewing assigned 47 Ringer 81 see also Ring tones off 81 S Safety 87 accessory 93 battery 92 driving 111 108 electromagnetic interference 90 medical devices 90 radio frequency 87 Security 83 Send key 1 Service provider 15 Service, activating 6 Settings 82 resetting 84 SIM card 3, 11
receiving 42 sending calls to 17, 42 setting up 8, 38, 41 Voice name 20, 30 creating 32 Voice records 63 creating 63 deleting 64 labelling 64 locking 64 memory 64 playing 63 Volume, setting 81, 83 W Waits dialing 71 storing 34 Warranty 99 Word mode 77 109
Index 110
Driving Safety Tips “Safety is your most important call!” Your Motorola wireless telephone gives you the powerful ability to communicate by voice — almost anywhere, anytime, wherever wireless phone service is available and safe conditions allow. But an important responsibility accompanies that benefits of wireless phones, one that every user must uphold. When driving a car, driving is your first responsibility.
Driving Safety Tips • Use your wireless phone to call for help. Dial 9-1-1 or other local emergency number in the case of fire, traffic accident or medical emergencies. • Use your wireless phone to help others in emergencies. If you see an auto accident, crime in progress or other serious emergency where lives are in danger, call 9-1-1 or other local emergency number, as you would want others to do for you. • Call roadside assistance or a special non-emergency wireless assistance number when necessary.
