Users Manual
Table Of Contents
- Other Systems
- 7.1 Push-To-Talk Button
- 7.2 Programmable Buttons
- 7.3 Status Indicators
- 7.4 Zone and Channel Selections
- 7.5 Calls
- 7.6 Advanced Features
- 7.6.1 Bluetooth®
- 7.6.2 Multi-Site Control
- 7.6.3 Talkaround
- 7.6.4 Monitor Feature
- 7.6.5 Home Channel Reminder
- 7.6.6 Remote Monitor
- 7.6.7 Scan Lists
- 7.6.8 Scan
- 7.6.9 Vote Scan
- 7.6.10 Call Indicator Settings
- 7.6.11 Call Alert Operation
- 7.6.12 Mute Mode
- 7.6.13 Emergency Operation
- 7.6.13.1 Sending Emergency Alarms
- 7.6.13.2 Sending Emergency Alarms with Call
- 7.6.13.3 Emergency Alarms with Voice to Follow
- 7.6.13.4 Sending Emergency Alarms with Voice to Follow
- 7.6.13.5 Receiving Emergency Alarms
- 7.6.13.6 Exiting Emergency Mode After Receiving the Emergency Alarm
- 7.6.13.7 Reinitiating Emergency Mode
- 7.6.13.8 Exiting Emergency Mode
- 7.6.14 Man Down
- 7.6.15 Text Messaging
- 7.6.16 Privacy
- 7.6.17 Lone Worker
- 7.6.18 Password Lock
- 7.6.19 Auto-Range Transponder System
- 7.6.20 Over-the-Air Programming
- 7.6.21 Wi-Fi Operation
- 7.7 Utilities
- 7.7.1 Checking Battery Strength
- 7.7.2 Flexible Receive List
- 7.7.3 Text-to-Speech
- 7.7.4 Turning Acoustic Feedback Suppressor On or Off
- 7.7.5 Turning Global Navigation Satellite System On or Off
- 7.7.6 Turning Radio Tones/Alerts On or Off
- 7.7.7 Power Levels
- 7.7.8 Voice Operating Transmission
- 7.7.9 Turning Option Board On or Off
- 7.7.10 Turning Voice Announcement On or Off
- 7.7.11 Switching Audio Route between Internal Radio Speaker and Wired Accessory
- 7.7.12 Turning Intelligent Audio On or Off
- 7.7.13 Turning Trill Enhancement On or Off
- Authorized Accessories List
- Maritime Radio Use in the VHF Frequency Range
- Batteries and Chargers Warranty
- Limited Warranty
7.6.8.3
Deleting Nuisance Channels
If a channel continually generates unwanted calls or noise,
(termed a "nuisance" channel), you can temporarily remove
the unwanted channel from the scan list. This capability
does not apply to the channel designated as the Selected
Channel. Follow the procedure to delete nuisance channels
on your radio.
1 When your radio locks on to an unwanted or
nuisance channel, press the programmed Nuisance
Channel Delete button until you hear a tone.
2 Release the programmed Nuisance Channel
Delete button.
The nuisance channel is deleted.
7.6.8.4
Restoring Nuisance Channels
Follow the procedure to restore nuisance channels on your
radio.
Do one of the following:
• Turn the radio off and then power it on again.
• Change the channel using the Channel Selector
Knob.
7.6.9
Vote Scan
Vote Scan provides you with wide area coverage in areas
where there are multiple base stations transmitting identical
information on different analog channels.
Your radio scans analog channels of multiple base stations
and performs a voting process to select the strongest
received signal. Once that is established, your radio
receives transmissions from that base station.
During a vote scan, the yellow LED blinks.
To respond to a transmission during a vote scan, see
Responding to Transmissions During Scanning on page
157.
English
158