Users Manual
Table Of Contents
- Other Systems
- 7.1 Push-To-Talk Button
- 7.2 Programmable Buttons
- 7.3 Status Indicators
- 7.4 Zone and Channel Selections
- 7.5 Calls
- 7.6 Advanced Features
- 7.6.1 Bluetooth®
- 7.6.2 Multi-Site Control
- 7.6.3 Talkaround
- 7.6.4 Monitor Feature
- 7.6.5 Home Channel Reminder
- 7.6.6 Remote Monitor
- 7.6.7 Scan Lists
- 7.6.8 Scan
- 7.6.9 Vote Scan
- 7.6.10 Call Indicator Settings
- 7.6.11 Call Alert Operation
- 7.6.12 Mute Mode
- 7.6.13 Emergency Operation
- 7.6.13.1 Sending Emergency Alarms
- 7.6.13.2 Sending Emergency Alarms with Call
- 7.6.13.3 Emergency Alarms with Voice to Follow
- 7.6.13.4 Sending Emergency Alarms with Voice to Follow
- 7.6.13.5 Receiving Emergency Alarms
- 7.6.13.6 Exiting Emergency Mode After Receiving the Emergency Alarm
- 7.6.13.7 Reinitiating Emergency Mode
- 7.6.13.8 Exiting Emergency Mode
- 7.6.14 Man Down
- 7.6.15 Text Messaging
- 7.6.16 Privacy
- 7.6.17 Lone Worker
- 7.6.18 Password Lock
- 7.6.19 Auto-Range Transponder System
- 7.6.20 Over-the-Air Programming
- 7.6.21 Wi-Fi Operation
- 7.7 Utilities
- 7.7.1 Checking Battery Strength
- 7.7.2 Flexible Receive List
- 7.7.3 Text-to-Speech
- 7.7.4 Turning Acoustic Feedback Suppressor On or Off
- 7.7.5 Turning Global Navigation Satellite System On or Off
- 7.7.6 Turning Radio Tones/Alerts On or Off
- 7.7.7 Power Levels
- 7.7.8 Voice Operating Transmission
- 7.7.9 Turning Option Board On or Off
- 7.7.10 Turning Voice Announcement On or Off
- 7.7.11 Switching Audio Route between Internal Radio Speaker and Wired Accessory
- 7.7.12 Turning Intelligent Audio On or Off
- 7.7.13 Turning Trill Enhancement On or Off
- Authorized Accessories List
- Maritime Radio Use in the VHF Frequency Range
- Batteries and Chargers Warranty
- Limited Warranty
Positive Indicator Tone
Radio is in talkaround mode.
Negative Indicator Tone
Radio is in repeater mode.
7.6.4
Monitor Feature
The feature allows you to remotely activate the microphone
of a target radio. You can use this feature to monitor any
audible activity surrounding the target radio.
NOTE:
This feature is not applicable in Capacity Plus–
Single-Site and Capacity Plus–Multi-Site.
7.6.4.1
Monitoring Channels
Follow the procedure to monitor channels.
1 Long press the programmed Monitor button.
If the channel is in use:
• You hear radio activity or total silence.
• The yellow LED lights up.
If the monitored channel is free, you hear a “white
noise".
2 Press the PTT button to talk. Release the PTT
button to listen.
7.6.4.2
Permanent Monitor
The Permanent Monitor feature is used to continuously
monitor a selected channel for activity.
7.6.4.2.1
Turning Permanent Monitor On or Off
Follow the procedure to turn Permanent Monitor on or off
on your radio.
Press the programmed Permanent Monitor button.
When the radio enters the mode:
• An alert tone sounds.
• The yellow LED lights up.
English
154