User's Guide
Table Of Contents
- Contents
- Supplier's Declaration of Conformity
- Important Safety Information
- Notice to Users (FCC)
- Notice to Users (Industry Canada)
- Software Version
- Intellectual Property and Regulatory Notices
- Computer Software Copyrights
- Radio Care
- Introduction
- Getting Started
- 2.1 Charging the Battery
- 2.2 Attaching the Battery
- 2.3 Attaching the Antenna
- 2.4 Attaching the Carry Holster
- 2.5 Attaching the Universal Connector Cover
- 2.6 Cleaning the Universal Connector Cover
- 2.7 Removing the Universal Connector Cover (Dust Cover)
- 2.8 Turning the Radio On
- 2.9 Turning the Radio Off
- 2.10 Adjusting the Volume
- Radio Controls
- WAVE
- Capacity Max
- 5.1 Push-To-Talk Button
- 5.2 Programmable Buttons
- 5.3 Status Indicators
- 5.4 Registration
- 5.5 Zone and Channel Selections
- 5.6 Calls
- 5.7 Advanced Features
- 5.7.1 Call Queue
- 5.7.2 Priority Call
- 5.7.3 Talkgroup Scan
- 5.7.4 Receive Group List
- 5.7.5 Priority Monitor
- 5.7.6 Multi-Talkgroup Affiliation
- 5.7.7 Talkback
- 5.7.8 Bluetooth®
- 5.7.9 Multi-Site Controls
- 5.7.10 Home Channel Reminder
- 5.7.11 Remote Monitor
- 5.7.12 Call Indicator Settings
- 5.7.13 Call Alert Operation
- 5.7.14 Mute Mode
- 5.7.15 Emergency Operation
- 5.7.16 Text Messaging
- 5.7.17 Privacy
- 5.7.18 Stun/Revive
- 5.7.19 Radio Kill
- 5.7.20 Lone Worker
- 5.7.21 Password Lock
- 5.7.22 Over-the-Air Programming
- 5.7.23 Wi-Fi Operation
- 5.8 Utilities
- 5.8.1 Checking Battery Strength
- 5.8.2 Text-to-Speech
- 5.8.3 Turning the Acoustic Feedback Suppressor Feature On or Off
- 5.8.4 Turning Global Navigation Satellite System On or Off
- 5.8.5 Turning Radio Tones/Alerts On or Off
- 5.8.6 Power Levels
- 5.8.7 Turning Option Board On or Off
- 5.8.8 Turning Voice Announcement On or Off
- 5.8.9 Switching Audio Route between Internal Radio Speaker and Wired Accessory
- 5.8.10 Turning Intelligent Audio On or Off
- 5.8.11 Turning Trill Enhancement On or Off
- Connect Plus
- 6.1 Additional Radio Controls in Connect Plus Mode
- 6.2 Making and Receiving Calls in Connect Plus Mode
When you receive a Private Call, the LED blinks green.
Your radio unmutes and the incoming call sounds through
the speaker of the radio.
1 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm)
from your mouth.
2 Press the PTT button to respond to the call.
The LED lights up solid green.
3 Wait for the Talk Permit Tone to finish (if enabled),
and speak clearly into the microphone.
4 Release the PTT button to listen.
If there is no voice activity for a predetermined period of
time, the call ends.
You hear a short tone.
See Making a Private Call
on page 100 for details on
making a Private Call.
6.2.5.3
Receiving a Site All Call
A Site All Call is a call from an individual radio to
every radio on the site. It is used to make important
announcements requiring the user's full attention.
When you receive an Site All Call, a tone sounds and the
LED blinks green.
Your radio unmutes and the incoming call sounds through
the radio speaker.
A Site All Call does not wait for a predetermined period of
time before ending.
You cannot respond to a Site All Call.
NOTE:
The radio stops receiving the Site All Call if you
switch to a different channel while receiving the call.
During a Site All Call, you will not be able to use any
programmed button functions until the call ends.
English
98