M MOTOTRBO XPRTM 7150 Non-Display Portable User Guide 68009677001-A
Declaration of Conformity DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola Solutions, Inc. Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A. Phone Number: 1-800-927-2744 Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. Hereby declares that the product: Model Name: XPR 7150 conforms to the following regulations: FCC Part 15, subpart B, section 15.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Contents Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . i Important Safety Information . . . . . . . . . . . . . . . . . vi RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios . . . . . . . . . . . . . . . . . . .vi Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Computer Software Copyrights . . . . . . . . . . . . . . . vii Open Source Software Legal Notices . . . . . . . . . vii Handling Precautions . . . . . . . . . . . . . . . . . . . .
Contents iv Receiving an All Call . . . . . . . . . . . . . . . . . . . . . . Receiving and Responding to a Phone Call . . . Phone Call as a Private Call or Group Call . . . Phone Call as an All Call . . . . . . . . . . . . . . . . . Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . Making a Call with the Channel Selector Knob . . Making a Group Call . . . . . . . . . . . . . . . . . . . . Making a Private Call . . . . . . . . . . . . . . . . . . . Making a Selective Call . . . . . . . .
Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . 49 Appendix: Maritime Radio Use in the VHF Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Special Channel Assignments . . . . . . . . . . . . . . . . 50 Emergency Channel . . . . . . . . . . . . . . . . . . . . . . 50 Non-Commercial Call Channel . . . . . . . . . . . . . . 51 Operating Frequency Requirements . . . . . . . . . . . . 51 Declaration of Compliance for the Use of Distress and Safety Frequencies . . . . . .
Important Safety Information RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios Important Safety Information ATTENTION! This radio is restricted to occupational use only. Before using this product, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and regulation.
Computer Software Copyrights This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Pat. Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.
Handling Precautions The MOTOTRBO Series Digital Portable radio meets IP67 specifications, allowing the radio to withstand adverse field conditions such as being submersed in water. • If the radio has been submersed in water, shake the radio well to remove any water that may be trapped inside the speaker grille and microphone port. Trapped water could cause decreased audio performance.
Getting Started This User Guide covers the basic operation of the MOTOTRBO Non-Display Portables. However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information. Throughout this publication, the icons below are used to indicate features supported in either the conventional Analog mode or conventional Digital mode: Getting Started Take a moment to review the following: How to Use This Guide . . . . .
What Your Dealer/System Administrator Can Tell You You can consult your dealer or system administrator about the following: • Is your radio programmed with any preset conventional channels? • Which buttons have been programmed to access other features? • What optional accessories may suit your needs? • What are the best radio usage practices for effective communication? • What maintenance procedures will help promote longer radio Getting Started life? 2 English
Preparing Your Radio for Use Your radio is powered by a Lithium-Ion (Li-lon) battery. To avoid damage and comply with warranty terms, charge the battery using a Motorola charger exactly as described in the charger user guide. It is recommended your radio remains powered off while charging. Charge a new battery 14 to 16 hours before initial use for best performance. IMPORTANT: ALWAYS charge your IMPRES battery with an IMPRES charger for optimized battery life and valuable battery data.
Attaching the Battery Attaching the Antenna Fit the battery into the slots at the bottom of the radio and push the top of the battery down until the latch snaps into place. With the radio turned off, set the antenna in its receptacle and turn clockwise. Preparing Your Radio for Use 3 1 To remove the antenna, turn the antenna counterclockwise. If antenna needs to be replaced, ensure that only MOTOTRBO antennas are used. Neglecting this will damage your radio.
Attaching the Carry Holster The universal connector is located on the antenna side of the radio. It is used to connect MOTOTRBO accessories to the radio. 1 Insert the slanted end of 2 3 the cover into the slots above the universal connector. Press downwards on the cover to seat the dust cover properly on the Universal Connector. Secure the dust cover to the radio by pushing the latch upwards. To remove the dust cover, push the latch downwards.
Attaching the Accessory Connector Preparing Your Radio for Use The accessory connector is to be secured to the universal connector on the antenna side of the radio. To attach the accessory connector, refer to the steps shown in the diagram. Powering Up the Radio 1 2 3 To remove the accessory connector, refer to the steps shown in the diagram. 6 English 3 Rotate the On/Off/Volume Control Knob clockwise until you hear a click. The LED lights up solid green.
Adjusting the Volume 3 1 To decrease the volume, turn this knob counterclockwise. NOTE: Your radio can be programmed to have a minimum volume offset where the volume level cannot be turned down fully. Check with your dealer or system administrator for more information. Preparing Your Radio for Use To increase the volume, turn the On/Off/Volume Control Knob clockwise.
Identifying Radio Controls Identifying Radio Controls Take a moment to review the following: Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9 Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . . page 10 Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . . page 12 Switching Between Conventional Analog and Digital Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13 IP Site Connect . . . . . . . . . . . . . . . . . . . . .
Radio Controls 5 Side Button 1* 11 2 10 3 6 Side Button 2* 7 Microphone 3 8 Speaker 9 Universal Connector for Accessories 1 4 9 5 8 6 7 10 Emergency Button 11 Antenna * These buttons are programmable Identifying Radio Controls 1 1 Channel Selector Knob 2 On/Off/Volume Control Knob 3 LED Indicator 4 Push-to-Talk (PTT) Button 9 English
Programmable Buttons Your dealer can program the programmable buttons as shortcuts to radio functions or preset channels/groups depending on the duration of a button press: • Short press – Pressing and releasing rapidly. • Long press – Pressing and holding for the programmed duration. Identifying Radio Controls • Hold down – Keeping the button pressed. NOTE: The programmed duration of a button press is applicable for all assignable radio/utility functions or settings.
Assignable Settings or Utility Functions Privacy Repeater/Talkaround*‡ Power Level – Toggles transmit power level between high and low. Scan* – Toggles scan on or off. Squelch normal. – Toggles privacy on or off. – Toggles between using a repeater and communicating directly with another radio. Site Lock On/Off*‡ – Toggles the automatic site roam on or off. Transmit Interrupt Remote Dekey – Stops an ongoing interruptible call to free the channel.
Push-To-Talk (PTT) Button During a call, if the Channel Free Indication feature is enabled on your radio (programmed by your dealer), you will hear a short alert tone the moment the target radio (the radio that is receiving your call) releases the PTT button, indicating the channel is free for you to respond. The PTT button on the side of the radio serves two basic purposes: Identifying Radio Controls • While a call is in progress, the PTT button allows the radio to transmit to other radios in the call.
Switching Between Conventional Analog and Digital Mode Channel Selector Knob This feature allows your radio to extend conventional communication beyond the reach of a single site, by connecting to different available sites which are connected via an Internet Protocol (IP) network. NOTE: This feature is not applicable in Capacity Plus. 3 1 When switching from digital to analog mode, certain features are unavailable. Your radio also has features available in both analog and digital mode.
A Members roam list supports a maximum of 16 channels (including the Selected Channel). You cannot manually add or delete an entry to the Members roam list. A Software License Key sold separately is required to use this feature. Check with your dealer or system administrator for more information. Capacity Plus Capacity Plus is a single-site trunking configuration of the MOTOTRBO radio system, which uses a pool of channels to support hundreds of users and up to 254 Groups.
Linked Capacity Plus Linked Capacity Plus allows your radio to extend trunking communication beyond the reach of a single site, by connecting to different available sites which are connected via an Internet Protocol (IP) network. It also provides an increase in capacity by efficiently utilizing the combined available number of programmed channels supported by each of the available sites.
Identifying Status Indicators Identifying Status Indicators Your radio indicates its operational status through the following: LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 16 Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17 Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 18 16 English LED Indicator The LED indicator shows the operational status of your radio.
Solid green – Radio is powering up or transmitting. Also indicates full charge of the battery when Battery Strength button is pressed. Blinking green – Radio is receiving a non-privacy-enabled call or data, detecting activity or retrieving Over-the-Air Programming transmissions over the air. Double blinking green – Radio is receiving a privacy-enabled Audio Tones Alert tones provide you with audible indications of the radio’s status or the radio’s response to data received.
Indicator Tones High pitched tone Low pitched tone Positive Indicator Tone Identifying Status Indicators Negative Indicator Tone 18 English
Receiving and Making Calls Use this navigation guide to familiarize yourself with the basic Call features: Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 20 Selecting a Channel . . . . . . . . . . . . . . . . . . . . . . . . . . page 20 Receiving and Responding to a Radio Call . . . . . . . . . page 20 Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . page 24 Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . page 28 Talkaround . .
Selecting a Channel Receiving and Making Calls Transmissions are sent and received on a channel. Depending on your radio’s configuration, each channel may have been programmed differently to support different groups of users or supplied with different features. After selecting the relevant Zone, select the relevant channel you require to transmit or receive on. Receiving and Responding to a Radio Call Once the channel, subscriber ID, or group ID is set, you can proceed to receive and respond to calls.
See Privacy on page 37 for more information. To receive a call from a group of users, your radio must be configured as part of that group. 1 The LED blinks green. Your radio unmutes and the incoming call sounds through the radio's speaker. 2 To respond, hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.
If the Voice Interrupt feature is enabled, press the PTT button to stop the current call from the transmitting radio and free the channel for you to talk/respond. 4 Press the PTT button to respond to the call. The LED lights up solid green. 5 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. Receiving and Making Calls 6 Release the PTT button to listen. 7 If there is no voice activity for a predetermined period of time, the call ends. 8 You hear a short tone.
Receiving and Responding to a Phone Call An All Call is a call from an individual radio to every radio on the channel. It is used to make important announcements requiring the user’s full attention. Phone Call as a Private Call or Group Call Procedure: Procedure: When you receive a Phone Call as a Private Call or Group Call: When you receive an All Call: 1 The LED blinks green. Your radio unmutes and the incoming 1 A tone sounds and the LED blinks green.
Phone Call as an All Call Procedure: When you receive a Phone Call as an All Call: The LED blinks green. Your radio unmutes and the incoming call sounds through the radio’s speaker. Receiving and Making Calls An All Call does not wait for a predetermined period of time before ending. NOTE: When you receive a Phone Call as an All Call, you can respond to the call or end the call, only if an All Call type is assigned to the channel.
Making a Call with the Channel Selector Knob To make a call to a group of users, your radio must be configured as part of that group. Procedure: 1 Select the channel with the active group alias or ID. See Selecting a Channel on page 20. OR Press the programmed One Touch Access button. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call. The LED lights up solid green.
Procedure: 1 Select the channel with the active group alias or ID. See Selecting a Channel on page 20. OR Press the programmed One Touch Access button. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. Receiving and Making Calls 3 Press the PTT button to make the call. The LED lights up solid green. 4 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. 5 Release the PTT button to listen.
Making an All Call Making a Phone Call with the Programmable Phone Button Procedure: Procedure: 1 Press the programmed Phone button. 1 Select the channel with the active group alias or ID. See 2 The LED lights up solid green. Selecting a Channel on page 20. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call. The LED lights up solid green. 4 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone.
Stopping a Radio Call Receiving and Making Calls This feature allows you to stop an ongoing Group or Private Call to free the channel for transmission. For example, when a radio experiences a “stuck microphone” condition where the PTT button is inadvertently pressed by the user. Talkaround You can continue to communicate when your repeater is not operating, or when your radio is out of the repeater’s range but within talking range of other radios. This is called “talkaround”.
Monitoring Features Permanent Monitor Use the Permanent Monitor feature to continuously monitor a selected channel for activity. Use the Monitor feature to make sure a channel is free before transmitting. NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus. NOTE: This feature is not applicable in Capacity Plus and Linked Capacity Plus. Procedure: 1 Press the programmed Permanent Monitor button. Procedure: 2 Radio sounds alert tone, and the LED lights up solid yellow.
Advanced Features Advanced Features Use this navigation guide to learn more about advanced features available with your radio: Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 30 Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 31 Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . . . . page 33 Call Alert Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . page 33 Emergency Operation . . . . . . . . . . . .
Scan During a dual mode scan, if you are on a digital channel, and your radio locks onto an analog channel, it automatically switches from digital mode to analog mode for the duration of the call. This is also true for the reverse. There are two types of scans: • Main Channel Scan (Manual): Your radio scans all the channels/groups in your scan list.
2 Press the PTT button during hang time. The LED lights up solid green. 3 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. 4 Release the PTT button to listen. 5 If you do not respond within the hang time, the radio returns to scanning other channels/groups.
Call Indicator Settings Escalating Alarm Tone Volume Your radio can be programmed by your dealer to continually alert you when a radio call remains unanswered. This is done by automatically increasing the alarm tone volume over time. This feature is known as Escalert. Call Alert Operation Button Procedure: 1 Press the programmed One Touch Access button to make a Call Alert to the predefined ID. 2 The LED lights up solid green when your radio is sending the Call Alert.
Emergency Operation An Emergency Alarm is used to indicate a critical situation. You are able to initiate an Emergency at any time, in any state, even when there is activity on the current channel. Your dealer can set the duration of a button press for the programmed Emergency button, except for long press, which is similar with all other buttons: • Short press – Between 0.05 seconds and 0.75 seconds • Long press – Between 1.00 second and 3.
3 When an Emergency Alarm acknowledgment is received, 4 Radio exits the Emergency Alarm mode. If your radio is set to Silent, it will not display any audio or visual indicators during Emergency mode. Sending an Emergency Alarm with Call This feature allows you to send an Emergency Alarm to a group of radios. Upon acknowledgement by a radio within the group, the group of radios can communicate over a programmed Emergency channel. Procedure: 1 Press the programmed Emergency On button.
Sending an Emergency Alarm with Voice to Follow This feature allows you to send an Emergency Alarm to a group of radios. Your radio’s microphone is automatically activated, allowing you to communicate with the group of radios without pressing the PTT button. This activated microphone state is also known as “hot mic”. Advanced Features If you press the PTT button during the programmed hot mic transmission period, the radio ignores the PTT press and remains in Emergency mode.
Reinitiating an Emergency Mode NOTE: There are two instances where this can happen: • You change the channel while the radio is in Emergency mode. This exits the Emergency mode. If Emergency Alarm is enabled on this new channel, the radio reinitiates Emergency. • You press the programmed Emergency On button during an Emergency initiation/transmission state. This causes the radio to exit this state, and to reinitiate Emergency.
If your radio receives a scrambled call that is of a different Privacy Key, OR a different Key Value and Key ID, you will either hear a garbled transmission (Basic Privacy) or nothing at all (Enhanced Privacy). Advanced Features The LED lights up solid green while the radio is transmitting and blinks green rapidly when the radio is receiving an ongoing privacy-enabled transmission.
Starting a Manual Site Search 1 Press the programmed Manual Site Roam button. 2 A tone sounds and the LED blinks green. 3 You hear a positive indicator tone and the LED turns off, indicating the radio is locked on to a site. OR You hear a negative indicator tone and the LED turns off, indicating the radio is unable to lock on to a site. This feature prompts an emergency to be raised if there is no user activity, such as any radio button press or activation of the channel selector, for a predefined time.
Password Lock Features If enabled, this feature allows you to access your radio via password upon powering up. Use the Channel Selector Knob and the three Side Buttons to enter password (see Linked Capacity Plus page 15 on page 8): • Channel Selector Knob positions 1 to 9 represent numbers 1 to 9, and position 10 represents number 0. • Side Buttons 1 to 2 represent numbers 1 to 2. Accessing the Radio from Password Procedure: Advanced Features 1 Power up the radio. 40 2 You hear a continuous tone.
Bluetooth Bluetooth operates within a range of 10 meters line of sight. This is an unobstructed path between your radio and your Bluetooth-enabled device. It is not recommended that you leave your radio behind and expect your Bluetooth-enabled device to work with a high degree of reliability when they are separated. At the fringe areas of reception, both voice and tone quality will start to sound "garbled" or "broken".
Disconnecting from a Bluetooth Device Procedure: 1 Press the programmed Bluetooth Disconnect button. 2 A positive indicator tone sounds when disconnected. ARTS is an analog-only feature designed to inform you when your radio is out-of-range of other ARTS-equipped radios. Switching Audio Route ARTS-equipped radios transmit or receive signals periodically to confirm that they are within range of each other. Your dealer can program your radio to transmit or receive the ARTS signal.
Over-the-Air Programming (OTAP) While undergoing OTAP, the LED blinks green. NOTE: When the radio is receiving high volume data, the channel is busy. A PTT button press at this time causes a negative tone to sound. Once the programming is complete, a tone sounds, and your radio restarts (powers off and on again). Setting the Squelch Level You can adjust your radio's squelch level to filter out unwanted calls with low signal strength or channels that have a higher than normal background noise.
Setting the Power Level • Follow the procedure below. You can toggle your radio’s power setting between high or low for each channel. NOTE: Turning this feature on or off is limited to radios with this function enabled. Check with your dealer or system administrator for more information. Settings: High enables communication with radios located at a considerable distance from you. Low enables communication with radios in closer proximity. Procedure: 1 Press the programmed Power Level button.
Voice Announcement You can enable and disable all radio tones and alerts (except for the incoming Emergency alert tone) if needed. This feature enables the radio to audibly indicate the current Zone or Channel the user has just assigned, or programmable button press. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display. Procedure: 1 Press the programmed All Tones/Alerts button.
Intelligent Audio Your radio automatically adjusts its audio volume to overcome current background noise in the environment, inclusive of both stationary and non-stationary noise sources. This feature is a Receive-only feature and does not affect Transmit audio. NOTE: This feature is not applicable during a Bluetooth session. Use the following features to toggle Intelligent Audio on or off. Procedure: Advanced Features Press the programmed Intelligent Audio button to toggle the feature on or off.
Accessories • Li-Ion, 1600mAH IP67 Battery (PMNN4440_R) Accessories Your radio is compatible with the accessories listed in this chapter. Contact your dealer for details. Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 47 Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 47 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 47 Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• Multi-Unit Charger Insert (PMLN5010_) Earbuds and Earpieces (PMLN5731_) • Earset with Boom Microphone, MagOne (PMLN5732_) • Earpiece In-Line Mic/PTT Swivel, MagOne (PMLN5727_) • Non-Secure Wireless Headset & Push-to-Talk Device with Speaker (AARLN4885_) • Receive-Only Flexible Earpiece for Remote Speaker (WADN4190_) • D-Shell Receive Only Earpiece (One Size) for Remote Speaker (PMLN4620_) • Receiver-Only Earpiece with Translucent Tube and Rubber Eartip for Remote Speaker (AARLN4941_) • 1-Wire Ear
Remote Speakers 3.5mm Jack (PMMN4071_) • IMPRES Remote Speaker Small, with 3.5mm Jack (PMMN4073_) • Remote Speaker Small, No Emergency, IP57 (PMMN4075_) • Remote Speaker Small with 3.
Appendix: Maritime Radio Use in the VHF Frequency Range Appendix: Maritime Radio Use in the VHF Frequency Range Take a moment to review the following: Special Channel Assignments. . . . . . . . . . . . . . . . . . . Operating Frequency Requirements . . . . . . . . . . . . . . Declaration of Compliance for the Use of Distress and Safety Frequencies. . . . . . . . . . . . . . . Technical Parameters for Interfacing External Data Sources. . . . . . . . . . . . . . . . . . . . . . .
Non-Commercial Call Channel Operating Frequency Requirements A radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows: • on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency • on ships subject to the Safety Convention, the radio must be capable of operating: • in the simplex mode on the ship station transmitting frequencies specified in the 156.025 – 157.
Appendix: Maritime Radio Use in the VHF Frequency Range Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Channel Number Transmit Receive 20 * 22 * 24 25 26 27 28 60 * 62 63 * 65 66 67** 68 69 71 72 73 157.000 157.050 157.100 157.150 157.200 157.250 157.300 157.350 157.400 156.025 156.075 156.125 156.175 156.225 156.275 156.325 156.375 156.425 156.475 156.575 156.625 156.675 161.600 161.650 161.700 161.750 161.800 161.850 161.900 161.950 162.000 160.625 160.675 160.725 160.775 160.
Declaration of Compliance for the Use of Distress and Safety Frequencies Input Voltage (Volts Peak-to-peak) Max Data Rate Impedance RS232 USB SB9600 18V 3.6V 5V 28 kb/s 5k ohm 12 Mb/s 90 ohm 9.6 kb/s 120 ohm Appendix: Maritime Radio Use in the VHF Frequency Range The radio equipment does not employ a modulation other than the internationally adopted modulation for maritime use when it operates on the distress and safety frequencies specified in RSS-182 Section 7.3.
Batteries and Chargers Warranty The workmanship warranty guarantees against defects in Batteries and Chargers Warranty workmanship under normal use and service. All MOTOTRBO Batteries Two (2) Years IMPRES Chargers (Single-Unit and Multi-Unit, Non-Display) Two (2) Years IMPRES Chargers (Multi-Unit with Display) One (1) Year English The capacity warranty guarantees 80% of the rated capacity for the warranty duration.
Limited Warranty I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: MOTOROLA SOLUTIONS, INC.
INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. III. STATE LAW RIGHTS: SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY.
VI.
Notes Notes 58 English
