User's Guide
Table Of Contents
- Declaration of Conformity
- Important Safety Information
- Software Version
- Informations importantes sur la sécurité
- Version du logiciel
- Computer Software Copyrights
- Documentation Copyrights
- Disclaimer
- Getting Started
- Preparing Your Radio for Use
- Charging the Battery
- Attaching the Battery‡
- Installing the Antenna
- Attaching the Accessory Connector Cover
- Installing Accessories with GCAI Connector
- Turning On Your Radio‡
- Adjusting the Volume†
- Pairing Radio with Pod and Earpiece†‡
- Pairing Radio with Mission Critical Remote Control Unit (RCU)
- Using the Carry Holster
- Tying Your Radio and Flexible Antenna to Your Body
- Identifying Radio Controls
- Identifying Status Indicators
- General Radio Operation
- Advanced Features
- Advanced Call Features
- Scan
- Call Alert Paging†‡
- Emergency Operation†‡
- Man Down†‡
- Secure Operations
- Trunking System Controls†‡
- Mission Critical Wireless - Bluetooth® -†‡
- Turning the Bluetooth On
- Turning the Bluetooth Off
- Re-Pair Timer
- Bluetooth Drop Timer
- Pairing the Bluetooth Device with Your Radio
- Indicating the Bluetooth Connection is Lost
- Turning the Bluetooth Audio On (Routing the Audio from Your Radio to the Headset)
- Turning the Bluetooth Audio Off (Routing the Audio from the Headset to Your Radio)
- Adjusting the Volume of Your Radio from Bluetooth Audio Device
- Clearing All Bluetooth Devices Information
- Programming Over Project 25 (POP 25) (ASTRO 25 and ASTRO Conventional)
- Utilities
- Flipping the Display on DRSM‡
- Controlling the Display Backlight‡
- Locking and Unlocking the Controls†‡
- Turning Voice Mute On or Off†‡
- Using the Time-Out Timer
- Using the Conventional Squelch Operation Features
- Using the Digital PTT ID Feature‡
- Using the Smart PTT Feature (Conventional Only)
- Voice Announcement†
- Helpful Tips
- Accessories
- Appendix: Maritime Radio Use in the VHF Frequency Range
- Glossary
- Commercial Warranty
Advanced Features
English
55
Pairing the Bluetooth Device with Your Radio
The range of Bluetooth operation is 10 meters line-of-sight
communication. This is an unobstructed path between the
location of the signal transmitter (your radio) and the location of
the receiver (your device or accessory).
Obstacles that can cause an obstruction in the line-of-sight
include trees, buildings, mountains, cars and etc.
It is NOT recommended that you leave your radio behind and
expect your accessory to work with a high degree of reliability
when they are separated.
At the fringe areas of reception, both voice and tone quality will
start to sound "garbled" or "broken". To correct this problem,
simply position the Accessory and radio closer to each other
(within the 10 meter defined range) to re-establish clear audio
reception.
Procedure:
Note: Bluetooth tones and Bluetooth preprogrammed buttons
must be preprogrammed by a qualified radio
technician. Check with your dealer or system
administrator for more information.
To view the Bluetooth LED state, your radio must not
be in Surveillance mode during the pairing process.
With your radio’s Bluetooth feature ON, and the Bluetooth tones
enabled:
1 Turn on the accessory, then place it close to your radio
aligning the Bluetooth Pairing Spot on your radio to the
Bluetooth Pairing Spot (a blue dot) on the accessory.
2 If the pairing process is successful your radio sounds an
incremental-pitched tone to indicate paired.
OR
If the pairing process fails, your radio sounds a short, low-
pitched tone. The display shows PAIRFAIL. Repeat step 1
again.
3 Your radio continues to connect to the device.
If the connecting process is successful, the blue LED blinks
solid blue for two seconds, your radio sounds an
incremental-pitched tone. The display shows <Device
Type> CONNCTED, and the Bluetooth icon turns from
b to
a.
OR
Bluetooth
Pairing
Spot
APX_3000_M1.book Page 55 Wednesday, December 5, 2012 11:04 AM