CLP Series Two-Way RadioTM User Guide Model CLP1010, CLP1040, and CLP1060 (with Bluetooth® Wireless Technology)
Document Copyrights No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable.
CONTENTS Computer Software Copyrights . . . . . . . . . iii Product Safety and RF Exposure Compliance . . . . . . . . . . . . . . . . . . . . . . iv FCC Licensing Information . . . . . . . . . . . . .v Interference Information . . . . . . . . . . . . . . . . . v Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .1 Radio Overview . . . . . . . . . . . . . . . . . . . . . . .2 Radio Controls. . . . . . . . . . . . . . . . . . . . . . . . .2 Getting Started . . . . . . . . . . . . . . . . . . . .
CONTENTS Power Supply, Adapter and Drop-in Tray Charger. . . . . . . . . . . . . . . . . . . . . .14 Charging the Battery . . . . . . . . . . . . . . . .15 Charging the Bluetooth Headset. . . . . . .18 Checking Battery Status . . . . . . . . . . . . .19 Advanced Radio Configuration (*) . . . . . . 29 Batteries and Chargers Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . .20 CLP Repeater Capability . . . . . . . . . . . . . . . 30 Instructions. . . . . . . . . . . . . . . . . . . . .
COMPUTER SOFTWARE COPYRIGHTS iii COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program.
RADIO FREQUENCY (RF) EXPOSURE SAFETY STANDARDS Product Safety and RF Exposure Compliance RF SAFETY STANDARDS Caution Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet contained with your radio. ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
INTERFERENCE INFORMATION This device complies with Parts 90 and 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. The CLP Series radio operates on radio frequencies that are regulated by the Federal Communications Commission (FCC). To transmit on these frequencies, you are required to have a license issued by the FCC. Application is made available on FCC Form 601 and Schedules D, H, and Remittance Form 159.
FCC LICENSING INFORMATION Before filling out your application, you must decide which frequency(ies) you can operate on: “Radio Frequency and Code Charts” on page 37. For questions on determining the radio frequency, call Motorola Product Services at: 1-800-448-6686. Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC to operate this radio and should not be made.
PACKAGE CONTENTS INTRODUCTION Your product package contains the following products and manuals: • CLP Series Two-way Radio™ • Swivel Belt Clip Holster • Lithium Ion Battery and Battery Door • Drop-In Tray Charger with Transformer • Audio Accessory • User Quick Reference • Warranty Card For product information, visit us at: www.motorola.
RADIO OVERVIEW RADIO CONTROLS Accessory Connector Power/Battery Button RADIO OVERVIEW Volume Control (+/-) Menu Button Smart Status Glow Push-to-Talk (PTT) Button 2
GETTING STARTED 2. Align the battery contacts with tabs in the battery compartment. Insert the contact side of the battery first, then press the battery down to secure in place. 3. Put the battery door back on the radio. Push down the latch to lock. INSTALL THE BATTERY 1. The CLP Series radios’ standard packaged models come with standard Lithium Ion battery and the standard Lithium Ion battery door.
Connecting a Wired Audio Accessory 3. Plug the audio accessory straight into the accessory connector on the radio. Screw the audio accessory plug into the connector until it is tight and fully engaged with the connector. 4. Turn the radio ON. Press either the Battery Status, Menu or Volume Control button to check for audio through the audio accessory. RADIO OVERVIEW Connect the wired audio accessory. 1. Turn the radio OFF. 2.
CONNECTING A BLUETOOTH WIRELESS ACCESSORY (SELECT MODELS ONLY) Note: Add Bluetooth Headset (Initial Pairing) Reconnect to Last Connected Bluetooth Headset 1. Turn the radio OFF. 2. Put Bluetooth headset in pairing mode. Refer to your Bluetooth headset instructions leaflet. 3. 1. Turn the radio OFF. 2. Press the power button to turn the radio ON. (Make sure the Bluetooth headset is turned ON). Press and hold the PTT button and power button simultaneously until radio shows the blue LED.
Turning the Radio On and Off • To turn the radio ON, press and hold the Power/ Battery button until you hear a short tone and the Smart Status Glow lights up. • To turn it OFF, press and hold the button until you hear a short tone and the Smart Status Glow (red) indicator blinks once. Adjusting the Volume Turn the radio ON and set volume level by pressing volume control (+/- button). A total of 16 volume levels are available. RADIO OVERVIEW Installing and Removing the Swivel Belt Clip Holster 1.
TRANSMITTING AND RECEIVING 1. To talk, press and hold the PTT button on the front of the radio (or on select wired audio accessories with an inline PTT). Speak clearly into the microphone on the audio accessory. When finished talking, release the PTT to listen. 2. To receive, listen through the earpiece at the volume level you have set. Press the PTT to respond. Note: The CLP Series radios always require the use of an audio accessory with microphone and speaker.
OPERATION WITH MENU SETTINGS Press Menu button to navigate through the Menu settings. Voice Assisted Operation feature* (* may not be available on certain previous shipping radios) At any time in Menu mode, short press PTT or wait 3 seconds to exit the menu. RADIO OVERVIEW HOW TO... STEP 1 STEP 2 Change Channel Press Menu button to navigate to Channel. Press +/- button to change channel. Enter Monitor Mode Press Menu button to navigate to Monitor.
Selecting a Channel • For CLP multi-channel models only: 1. When powered ON, press the Menu button, you can hear the voice prompt: 2. [Color] “Channel” – [Channel#] – “To change” – “press +/-” Select the channel you want. The LED reflects the color of the new channel. Press PTT button to confirm or it is activated after 3 second hang time.
Monitoring a Channel 1. 1. To activate, press the Menu button to navigate to Monitor mode. Press the Menu button to navigate to Scan mode. 2. 2. When Monitor is OFF, you can hear the voice prompt: “Monitor” – “To activate” – “press +/-”. When Scan is OFF, you can hear the voice prompt: “Scan” – “To activate” – “press +/-”. 3. 3. Press either “+/-“ button to activate the Monitor; press either “+/-“ button again to deactivate.
Dynamic Talkaround Scan (*) Mute Feature (*) "Dynamic Talkaround Scan" is a simple but effective method for an on-site repeater enabled two-way radio systems to maximize communication coverage. This feature can be enabled on a repeater channel via the Customer Programming Software (CPS). The Dynamic Talkaround Scan gives the radio the ability to scan both the transmit and receive frequencies of a repeater channel. You can quickly lower the headset volume using the Mute feature.
BATTERY AND CHARGER FEATURES BATTERY AND CHARGER FEATURES BATTERY FEATURES The CLP Series radio provides Lithium-Ion batteries that come in different capacities that define the battery life. About the Li-Ion Battery The CLP Series radio comes equipped with a rechargeable Li-Ion battery. This battery should be charged before initial use to ensure optimum capacity and performance. Battery life is determined by several factors.
Battery Recycling and Disposal Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, access RBRC's Internet web site at: http://www.call2recycle.org or call: 1- 877-723-1297. This internet site and telephone number also provides other useful information concerning recycling options for consumers, businesses and governmental agencies. 13 BATTERY AND CHARGER FEATURES Li-Ion rechargeable batteries can be recycled.
BATTERY AND CHARGER FEATURES Removing the Lithium-Ion (Li-Ion) Battery Power Supply, Adapter and Drop-in Tray Charger Battery Latch 1. Turn OFF the radio. 2. Push up the latch at the bottom of the battery door and lift the battery door off the radio. 3. Pull the battery away from the radio. 14 The radio is packaged with one Drop-in Tray Charger with transformer. For details, see “Chargers” Section on page 47.
Charging the Battery Charging a Standalone Battery 1. Note: BATTERY AND CHARGER FEATURES To charge the battery (with the radio attached): Place it in a Motorola-approved Drop-in Tray Single Unit Charger or Drop-in Tray Multi Unit Charger. When acquiring additional chargers or power supplies, make sure you have similar drop-in tray chargers and power supplies sets. For part number details, refer to “Chargers” Section on page 47.
BATTERY AND CHARGER FEATURES Charging with the Drop-in Tray Single Unit Charger (SUC) 1. Place the drop-in tray charger on a flat surface. 2. Insert the connector of the power supply into the Micro USB port on the front of the drop-in tray charger. 3. Connect the correct power supply to a proper AC outlet. 4. Insert the radio into the tray, making sure the charging contacts on the charger are aligned with the contacts on the radio.
Note: Note: • For part number details, refer to the“Accessories” Section on page 46. Insert the radio (with battery installed) into the charging pocket. The radio fits in the charger with the holster attached when placed face down in the tray. The battery can be charged by itself using the slot on the flat surface of the charging pocket. Charger LED Indicator Status On the MUC, each of the 6 charging pockets has an LED. The LEDs are grouped into pairs to show which charging pockets are paired.
BATTERY AND CHARGER FEATURES Charging the Bluetooth Headset • Refer to your Bluetooth headset leaflet for charging instruction. Note: Charging Bluetooth Headset with CLP Series Drop-In Tray Multi-Unit Charger and Cloning Cable (Optional Accessory) You can also charge your Bluetooth headset with CLP Series Multi Unit Charger (MUC) P/N HKPN4007 (optional accessory) and Cloning Cable P/N HKKN4026 (optional accessory).
Checking Battery Status After the Smart Status Glow and Voice Assisted Operation features (*) indicate the BATTERY STATUS, it returns to the current channel color. Note: (*) May not be available on certain previous shipping radios.
BATTERIES AND CHARGERS SAFETY INFORMATION BATTERIES AND CHARGERS SAFETY INFORMATION 3. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting the charger. 4. An extension cord should not be used unless This document contains important safety and absolutely necessary. Use of an improper operating instructions. Read these instructions extension cord could result in risk of fire and carefully and save them for future reference.
OPERATIONAL SAFETY GUIDELINES Turn the radio OFF when charging battery. • The charger is not suitable for outdoor use. Use only in dry locations/conditions. • Connect charger only to an appropriately fused and wired supply of the correct voltage (as specified on the product). • Disconnect charger from line voltage by removing main plug. • The outlet to which this equipment is connected should be nearby and easily accessible.
PROGRAMMING THE RADIO THROUGH THE CPS RADIO PROGRAMMING OVERVIEW Downloading the (Customer Programming Software) CPS Programming the Radio To program the radio: 1. Connect the radio via the Drop-in Charger Tray or the Charging Pocket with “PROG” label on the Multi-Unit Charger and CPS Programming Cable. PROGRAMMING THE RADIO THROUGH THE CPS You can program or change features on your CLP radios by using the Computer Programming Software (CPS) and the CPS Programming Cable (*).
2. Make sure the radio is turned ON. 3. Once the radio is connected, open the CPS and select “Read” on the toolbar to get the radio profile. The CPS allows the user to change settings, such as General, Audio, Menu, Channels, Scan List, Customized PL/DPL, Bluetooth (*) as well as select frequencies, PL/ DPL codes on each channel. 4. After you change the settings, press “Write” on the toolbar to save the settings.
CLP1060 1W UHF 6 CH Bluetooth Radios Default Settings - BRUS Frequency # Frequency Settings Code Value (Hz) Band width (kHz) 1 2 464.5500 67.0 12.5 2 8 467.9250 67.0 12.5 3 5 467.8500 67.0 12.5 4 6 467.8750 67.0 12.5 5 10 461.0625 67.0 12.5 6 12 461.1125 67.0 12.
RADIO CLONING CLONING RADIO SETTINGS A multi-channel radio can be cloned to a singlechannel radio BUT only the first channel is cloned. The Multi-Unit Charger (MUC) does not have to be plugged in for cloning, but both radios require charged batteries. Note: The enhanced CLP software also uses the LED to indicate “pass” or “fail” status during cloning. Green LED during cloning indicates “pass” status and red LED during cloning indicates “fail” status.
RADIO CLONING 2. Note: Plug one side of the cloning cable microconnector to one Single Unit Charger. Plug the other end to the second Single Unit Charger. During the cloning process no power is being applied to the Single Unit Charger. The batteries cannot be charged. A data communication is being established between the two radios. 3. Turn ON the “Target Radio” and place it into one of the Single Unit Chargers. 4.
What to do if cloning fails The radio emits an audible “bonk” indicating that the cloning process has failed. In the event following before trying to start the cloning process again. 1. Make sure that the radio batteries on both radios are fully charged. 2. Verify the cloning cable connection on both Single Unit Chargers. 3. Make sure that the battery is engaged properly on to the radio. 4. Make sure that there is no debris in the charging tray or on the radio contacts. 5.
RADIO CLONING Cloning Radios using the CLP Series MultiUnit Charger (MUC) Kit P/N HKPN4007 (optional accessory) Cloning the Radio through a Multi-Unit Charger 1. To put the source radio into clone mode, press and hold PTT and the “-” button while turning the radio ON until you hear the Cloning Tone and Double Blinking Orange on the Smart Status Glow. 2. Place the source radio into one of the charging pockets that has the “CLONE” label. 28 3.
ADVANCED RADIO CONFIGURATION (*) (*) Enhancement feature on CLP radios. May not be available on previous shipping radios. Advanced Radio Configuration provides you with the ability to view and configure the following settings without the need to use a computer. 1. Press the PTT, + Button and Power button and hold for 3 to 5 seconds until you hear a “chirp” sound and the voice prompt “Programming Mode”. Note: 2. • The LED Indicator starts blinking a green heartbeat.
CLP REPEATER CAPABILITY: WORKING WITH RPX Programming the RPX through a Single Unit Charger CLP REPEATER CAPABILITY Use the Single Unit Charger or use the pocket with “PROG” label on the Multi-Unit Charger to clone the RPX. CLP REPEATER CAPABILITY: WORKING WITH RPX Note: Connect the RDX Serial Clone Cable (P/N RLN6303) and the Mini-USB to the Micro-USB Adapter Cable in order to link the CLP and RPX units. Programming the RPX through a Single Unit Charger INSTRUCTIONS 1.
4. Press the “Menu” button on the CLP radio to start the cloning process. 5. Once the cloning is completed, turn the RPX OFF and back ON again in order to activate the radio. 6. To clone another RPX, repeat steps 3, 4 and 5. 7. To exit clone mode on the CLP radio, turn the radio OFF. Programming the RPX through a Multi-Unit Charger 1. Place the CLP radio into one of the charging pockets that has the “PROG” label indicated. 2.
TROUBLESHOOTING TROUBLESHOOTING Symptom Try this No Power Recharge or replace Li-Ion battery. Extreme operating temperatures affect battery life. Refer to “About the Li-Ion Battery” Section on page 12. Hearing other noises or conversation on a channel Confirm Interference Eliminator Code is set. Frequency or Interference Eliminator Code may be in use. Change settings: either change frequencies or codes on all radios. Make sure radio is at the right frequency and code when transmitting.
Try this Limited talk range Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease range. Check for clear line of sight to improve transmission. Change location of radio. To increase range and coverage, you can either reduce obstructions or increase power. UHF radios provide greater coverage in industrial and commercial buildings. Increasing power provides greater signal range and increased penetration through obstructions.
TROUBLESHOOTING Symptom Try this Heavy static or interference Radios are too close, they must be at least five feet apart. Radios are too far apart or obstacles are interfering with transmission. Low batteries Recharge or replace Li-Ion battery. Extreme operating temperatures affect battery life. Refer to “About the Li-Ion Battery” Section on page 12.
Try this Unable to pair a Bluetooth headset Make sure the target Bluetooth headset is not connected to another device. Unable to connect to a Bluetooth headset Make sure the target Bluetooth headset is not connected to another device. Pairing with wrong Bluetooth headset Don’t perform pairing procedures next to other Bluetooth headset devices. CLP Bluetooth uses proximity pairing. Make sure the headset is placed next to the CLP radio.
USE AND CARE USE AND CARE Use a soft damp cloth to clean the exterior. Do not immerse in water. Do not use alcohol or cleaning solutions. If the portable is submerged in water... Turn OFF and remove batteries. 36 Dry with soft cloth. Do not use until completely dry.
RADIO FREQUENCY AND CODE CHARTS These charts provide frequency information and are useful when using Motorola CLP Series TwoWay Radios with other business radios. Most of the frequency positions are the same as Spirit M, GT, S, XTN, RDX and CLS Series frequency positions (where applicable), the bandwidths are different. CLP UHF Frequencies Band width (kHz) Freq. # Frequency (MHz) Band width (kHz) Freq. # 1 464.5000 12.5 13 461.1375 12.5 2 464.5500 12.5 14 461.1625 12.5 3 467.7625 12.
CLP UHF Frequencies Frequency (MHz) Band width (kHz) Freq. # Frequency (MHz) Band width (kHz) Freq. # 49 467.8375 12.5 60 462.5125 12.5 50 467.8625 12.5 61 467.1875 12.5 51 467.8875 12.5 62 467.4625 52 467.9125 12.5 63 53 469.4875 12.5 54 469.5125 55 RADIO FREQUENCY AND CODE CHARTS Band width (kHz) Frequenc y (MHz) Band width (kHz) Freq. # 71 451.6375 12.5 81 468.2125 12.5 72 452.3125 12.5 82 468.2625 12.5 12.5 73 452.5375 12.5 83 468.3125 12.5 467.
CTCSS/DPL Interference Eliminator Codes Code CTCSS/DPL Code DPL Code DPL Code DPL Code 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Disabled 67 71.9 74.4 77 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100 103.5 107.2 110.9 114.8 118.8 123 127.3 131.8 136.5 141.3 146.2 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 122 39 40 41 42 43 44 45 46 151.4 156.7 162.2 167.9 173.8 179.9 186.2 192.8 203.5 210.7 218.1 225.7 233.6 241.8 250.3 69.
CTCSS/DPL Interference Eliminator Codes (cont’d) DPL Code DPL Code DPL Code DPL Code 120 743 146 Inverted DPL 55 171 Inverted DPL 80 195 Inverted DPL 104 RADIO FREQUENCY AND CODE CHARTS 121 754 147 Inverted DPL 56 172 Inverted DPL 81 196 Inverted DPL 105 123 645 148 Inverted DPL 57 173 Inverted DPL 82 197 Inverted DPL 106 124 Customized PL 149 Inverted DPL 58 174 Inverted DPL 83 198 Inverted DPL 107 125 Customized PL 150 Inverted DPL 59 175 Inverted DPL 84 199
What Does this Warranty Cover? Subject to the exclusions contained below, Motorola, Inc.
WARRANTY Exclusions Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage. Batteries. Only batteries whose fully charged capacity falls below 80 % of their rated capacity and batteries that leak are covered by this limited warranty. Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.
Software. Applies only to physical defects in the media that embodies the copy of the software (e.g. CDROM, or floppy disk). WHO IS COVERED? This warranty extends only to the first consumer purchaser, and is not transferable. Software Products Covered Software NOT Embodied in Physical Media. Software that is not embodied in physical media (e.g. software that is downloaded from the internet), is provided “as is” and without warranty. Length of Coverage Ninety (90) days from the date of purchase.
WARRANTY You will receive instructions on how to ship the Products to Motorola. You must ship the Products to us with freight, duties and insurance prepaid.
EXPORT LAW ASSURANCES This product is covered by one or more of the following United States patents. 5896277 5894292 5864752 5699006 5742484 D408396 D399821 D387758 D389158 5894592 5893027 5789098 5734975 5861850 D395882 D383745 D389827 D389139 5929825 5926514 5953640 6071640 D413022 D416252 D416893 D433001 This product is controlled under the export regulations of the United States of America.
ACCESSORIES AUDIO ACCESSORIES ACCESSORIES Part No. Part No.
CHARGERS Part No. Description HKPN4007_ CLP Series Multi Unit Charger (MUC) Kit HKPN4008_ CLP Series Single Unit Charger (SUC) Kit PROGRAMMING CABLES Description HKKN4025_ CLP Series CPS Cable Kit HKKN4026_ CLP Series Cloning Cable Kit RLN6303_ RDX Serial Clone Cable Note: ACCESSORIES Part No. (*) Certain accessories may be or may not be available at the time of purchase. For latest information on accessories, contact your Motorola point of purchase or visit: www.motorola.
ACCESSORIES Notes 48
M Motorola Inc. 1301 E. Algonquin Rd. Schaumburg, IL 60196-1078 U.S.A. MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. © 2010 by Motorola, Inc. All rights reserved. Printed in Malaysia.
