ASTRO XTS 2500 ® TM Digital Portable Radio Model I User Guide
Radio On/Off ASTRO® XTS™ 2500 Digital Portable Radio, Model I Quick Reference Card Product Safety and RF Exposure Compliance ! Caution Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
ASTRO® XTS™ 2500 Digital Portable Radio Model I User Guide 6881094C04-D MOTOROLA, the Stylized M Logo, ASTRO, and CommPort are registered in the U.S. Patent & Trademark Office. All other product or service names are the property of their respective owners. P25 radios contain technology patented by Digital Voice Systems, Inc. © Motorola, Inc. 2004. All Rights Reserved. Printed in the U.S.A. 4/15/04. Motorola, Inc. 8000 W. Sunrise Blvd. Ft.
This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola, Inc. Address: 8000 West Sunrise Boulevard Plantation, FL 33322 USA Phone Number: 1-888-567-7347 Hereby declares that the product: Model Name: XTS 2500 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.
Product Safety and RF Exposure Compliance ! Caution Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design.
Contents Declaration of Conformity .................................................................. ii Product Safety and RF Exposure Compliance .................................iii Computer Software Copyrights .........................................................iii Documentation Copyrights ................................................................iii Disclaimer ........................................................................................ iv General Radio Operation .................
PL Defeat .........................................................................................21 Time-out Timer ................................................................................22 Emergency ......................................................................................23 Send an Emergency Alarm .......................................................24 Send a Silent Emergency Alarm ...............................................25 Send an Emergency Call ............................
Accessories ................................................................. 43 Antennas ......................................................................................... 43 Batteries .......................................................................................... 43 Carry Accessories ........................................................................... 44 Belt Clips .................................................................................. 44 Body-Worn .....................
viii Table 1: Channel Map Use the chart below to map the channels (Cx) and zones (Zx) for your radio.
General Radio Operation Notations Used in This Manual You will notice the use of WARNINGS, CAUTIONS, and Notes throughout this manual. These notations are used to emphasize that safety hazards exist and that care must be taken or observed. ! An operational procedure, practice, condition, etc. exists which may result in injury or death if not carefully observed. WARNING ! An operational procedure, practice, condition, etc. exists which may result in damage to the equipment if not carefully observed.
General Radio Operation XTS 2500 Model I Radio 6 7 8 9 10 11 12 13 14 2 1 2 3 4 5
General Radio Operation Physical Features of the XTS 2500 Model I Radio Item Page Page 8 On/Off/Volume Control Knob 14 9 Microphone 1 Antenna 2 Top Button (programmable) 3 LED 4 Speaker 5 Universal Connector 6 16-Position Knob (programmable) 13 Side Button 2 (programmable) 7 3-Position Concentric Switch (programmable) 14 Battery ASTRO XTS 2500 Model I 10 Item 5 10 Top Side (Select) Button (programmable) 11 Push-to-Talk (PTT) Button 12 12 Side Button 1 (programmable) 8 3
General Radio Operation Programmable Features The programmable controls on your radio can be programmed by a qualified technician to operate certain software-activated features. The features that can be assigned to these controls, and the page numbers where these features can be found, are listed below.
General Radio Operation LED Indicators Table 2: LED Indicators This LED Color: indicates: RED (Non-flashing) Transmitting RED (Flashing) • Channel Busy OR • Low Battery (lights while transmitting) GREEN (Flashing) Receiving Individual Call Alert Tones Your radio uses alert tones to inform you of radio conditions. Table 3: Alert Tones You hear: Short, Low-Pitched Tone Tone Name Heard: Invalid Key-Press when the wrong key is pressed.
General Radio Operation Table 3: Alert Tones (Continued) You hear: Long, Low-Pitched Tone A Group of Low-Pitched Tones (Busy Tone) Tone Name No ACK Received when the radio does not receive an acknowledgment. Time-Out Timer Timed Out after time out. Talk Prohibit/ PTT Inhibit when the PTT button is pressed, and transmissions are prevented. Out-of-Range when the PTT button is pressed, but the radio is out of range of the system. Invalid Mode when the radio is set to an unprogrammed channel.
General Radio Operation Table 3: Alert Tones (Continued) You hear: Tone Name Volume Set Long, MediumPitched Tone Emergency Exit Failsoft Heard: when volume changed on a quiet channel. upon exiting the emergency state. when the trunking system fails. Automatic Call Back when the voice channel is available from the previous request. Talk Permit (When pressing the PTT button) verifies the system is accepting transmissions.
General Radio Operation Standard Accessories Battery ! WARNING To avoid a possible explosion: • DO NOT replace the battery in any area labeled “hazardous atmosphere”. • DO NOT discard batteries in a fire. Charge the Battery The Motorola approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance.
General Radio Operation Attach the Battery 1 With the radio off, fit the three extensions at the bottom of the battery into the bottom slots on the radio. 2 Press the top of the battery against the radio until both latches click into place. Remove the Battery 1 With the radio off, slide down the latches on the sides of the battery. 2 Pull the top of the battery away from the radio.
General Radio Operation Antenna For information regarding other available antennas, see page 43. Attach the Antenna With the radio off, turn the antenna clockwise to attach it. Remove the Antenna With the radio off, turn the antenna counter-clockwise to remove it.
General Radio Operation Belt Clip Attach the Belt Clip 1 Align the grooves of the belt clip with those of the battery. 2 Press the belt clip downward until you clear a “click.” Remove the Belt Clip 1 Use a flat-bladed object to press the belt clip tab away from the battery. 2 Slide the belt clip upward to remove it.
General Radio Operation Universal Connector Cover The universal connector cover is located on the antenna side of the radio. It is used to connect certain accessories to the radio. Note: To prevent damage to the connector, shield it with the connector cover when not in use. Remove the Connector Cover 1 Insert a flat-bladed screwdriver into the area between the bottom of the cover and the slot below the connector.
General Radio Operation Remote Speaker Microphone Adapter The Remote Speaker Microphone (RSM) adapter is located on the back of the radio, just above the battery. It must be used to connect the RSM accessories (see page 45) to the radio. If the RSM is not used, the adapter should be removed. Remove the Adapter Lift the larger side (below the antenna port) of the adapter away from the radio using your finger.
General Radio Operation Radio On and Off Turn the Radio On Turn the On/Off/Volume Control knob clockwise. • If the test is successful, you hear a mediumpitched tone. • If the test is unsuccessful, you hear a low-pitched tone. Turn off the radio, check the battery, and turn the radio on. Turn the Radio Off Turn the On/Off/Volume Control knob counterclockwise until it clicks.
General Radio Operation Zones and Channels A zone is a grouping of channels. A channel is a group of radio characteristics, such as transmit/receive frequency pairs. Before you use your radio to receive or send messages, you should select the zone. Select a Zone 1 If a control on your radio has been preprogrammed as the Zone switch, move the Zone switch to the position for the zone you want.
General Radio Operation Receive / Transmit Radio users who switch from analog to digital radios often assume that the lack of static on a digital channel is an indication that the radio is not working properly. This is not the case. Digital technology quiets the transmission by removing the “noise” from the signal and allowing only the clear voice or data information to be heard. This section emphasizes the importance of knowing how to monitor a channel for traffic before keying-up to send a transmission.
General Radio Operation Use the Preprogrammed Volume Set Button 1 Turn the radio on and select the desired zone and channel. See Turn the Radio On, page 14 and Zones and Channels, page 15. 2 Press and hold the Volume Set button to hear the volume set tone. 3 Release the Volume Set button. 4 Adjust the Volume Control Knob if necessary. 5 Press and hold the PTT button to transmit. LED lights RED while transmitting. 6 Release the PTT button to receive (listen).
General Radio Operation Use the Preprogrammed Monitor Button 1 Turn the radio on and select the desired zone and channel. 2 Press the Monitor button and listen for activity. (See the following Conventional Mode Operation.) 3 Adjust the Volume Control knob if necessary. 4 Press and hold the PTT button to transmit. The LED lights RED while transmitting. 5 Release the PTT button to receive (listen).
General Radio Operation Conventional Mode Operation Your radio may be programmed to receive Private-Line® (PL) calls. 1 Momentarily press the Monitor button to listen for activity. 2 Press and hold the Monitor button to set continuous monitor operation. (The duration of the button press is programmable.) 3 Press the Monitor button again, or the PTT button, to return to the original squelch setting.
General Radio Operation Notes 20
Common Radio Features Selectable Power Level This feature lets you select the power level at which your radio will transmit. The radio will always turn on to the preprogrammed default setting. This feature must be programmed by a qualified radio technician. • Select LOW for a shorter transmitting distance and to conserve power. • Select HIGH for longer transmitting distance. Place the preprogrammed Transmit Power Level switch in the high-power or low-power position.
Common Radio Features Time-out Timer The time-out timer turns off your radio’s transmitter. The timer is set for 60 seconds at the factory, but it can be programmed from 0 to 7.75 minutes (465 seconds) by a qualified radio technician. 1 2 3 22 Hold down the PTT longer than the programmed time. You will hear a short, lowpitched warning tone, the transmission is cut-off, and the LED will go out until you release the PTT.
Common Radio Features Emergency If the top (orange) button is programmed to send an emergency signal, then this signal overrides any other communication over the selected channel. Your radio can be programmed for the following: • Emergency Alarm • Emergency Alarm with Emergency Call • Silent Emergency Alarm • Emergency Call Consult a qualified radio technician for emergency programming of your radio.
Common Radio Features Send an Emergency Alarm An Emergency Alarm will send a data transmission to the dispatcher, identifying the radio sending the emergency. 1 With your radio turned on, press the Emergency button. The red LED lights, and you hear a short, medium-pitched tone. • Red LED • Short tone Note: To exit emergency at any time, press and hold the Emergency button for about a second.
Common Radio Features Send a Silent Emergency Alarm 1 With your radio turned on, press the Emergency button. The LED does not light, and you hear no tones. • LED does not light • No tones Note: To exit emergency at any time, press and hold the Emergency button for about a second. 2 The silent emergency state continues until you: Press and hold the Emergency button for about a second to exit the emergency state.
Common Radio Features 3 Release the PTT button to end the transmission and wait for a response from the dispatcher. 4 Press and hold the Emergency button for about a second to exit emergency. The radio operates in the normal dispatch manner while in Emergency Call, except, if enabled, it will return to one of the following: Using this operation: means you will talk... 1. Tactical/Non-Revert on the channel you selected before you entered the emergency state. 2.
Common Radio Features Emergency Keep-Alive With Emergency Keep-Alive enabled, if the radio is in the Emergency state, you cannot turn off the radio by using the On/Off Volume Control knob. With Keep-Alive, the radio will only exit the Emergency state using one of the ways mentioned in the previous sections (Emergency Alarm, Silent Emergency Alarm, or Emergency Call).
Common Radio Features Scan The scan feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels. The list must be preprogrammed by a qualified technician. Turn Scan On and Off Use the Preprogrammed Scan On/Off Switch Place the Scan On/Off Switch in the “scan on” or “scan off” position. Delete a Nuisance Channel When the radio scans to a channel that you do not wish to hear (nuisance channel), you can temporarily delete the channel from the scan list.
Common Radio Features Conventional Scan Only Make a Dynamic Priority Change While the radio is scanning, the dynamic priority change feature lets you temporarily change any channel in a scan list (except the priorityone channel) to the priority-two channel. The replaced priority-two channel becomes a non-priority channel. This change remains in effect until scan is turned off, then scanning reverts back to the preprogrammed state.
Common Radio Features Telephone Calls (Trunking Only) Use your radio to receive standard phone calls. A landline phone can be used to call a radio. Answer a Phone Call Use the Preprogrammed Call Response Button 1 When a phone call is received you hear telephone-type ringing and the LED flashes GREEN. 2 Press the Call Response button within 20 seconds after the call indicators begin. 3 Press and hold the PTT button to talk; release it to listen. 4 Press the Call Response button to hang up.
Common Radio Features Private Calls (Trunking Only) These one-to-one calls between two radios are not heard by others in the current talkgroup. Answer a Private Call Use the Preprogrammed Call Response Button. 1 When a private call is received you hear two alert tones and the LED flashes GREEN. 2 Press the preprogrammed Call Response button within 20 seconds. 3 Press and hold the PTT button to talk; release it to listen. 4 Press the Call Response button to hang up.
Common Radio Features Call Alert Paging Call Alert allows your radio to work like a pager. Answer a Call Alert Page 1 2 32 When a Call Alert Page is received, you hear four repeating alert tones and the LED flashes GREEN. Press and hold the PTT button to talk, release it to listen.
Common Radio Features Repeater or Direct Operation Also known as TALKAROUND operation, DIRECT lets you bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. REPEATER operation increases the radio’s range by connecting with other radios through a repeater. Transmit and receive frequencies are different. Select Repeater or Direct Operation Place the preprogrammed Repeater/Direct switch in Repeater or Direct position.
Common Radio Features Notes 34
Special Radio Features Trunking System Controls Failsoft The failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation, and automatically switches to its failsoft channel. During failsoft operation: • Your radio transmits and receives in conventional operation on a predetermined frequency. • You hear a medium-pitched tone every 10 seconds.
Special Radio Features Site Lock This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system. Lock or Unlock a Site Press the preprogrammed Site Lock/Unlock button. • The site lock state changes. Site Change You can force your radio to change to a new site.
Helpful Tips Radio Care Cleaning To clean the external surfaces of your radio: 1 Combine one teaspoon of mild dishwashing detergent to one gallon of water (0.5% solution). 2 Apply the solution sparingly with a stiff, non-metallic, shortbristled brush, making sure excess detergent does not get entrapped near the connectors, controls or crevices. Dry the radio thoroughly with a soft, lint-free cloth. 3 Clean battery contacts with a lint-free cloth to remove dirt or grease.
Helpful Tips Service Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services.
Helpful Tips Battery Battery Life Battery life is determined by several factors. Among the more critical are the regular overcharge of batteries and the average depth of discharge with each cycle. Typically, the greater the overcharge and the deeper the average discharge, the fewer cycles a battery will last. For example, a battery which is overcharged and discharges 100% several times a day, will last fewer cycles than a battery that receives less of an overcharge and is discharged to 50% per day.
Helpful Tips Battery Recycling and Disposal Nickel-cadmium (NiCd) rechargeable batteries can be recycled. However, recycling facilities may not be available in all areas. Under various U.S. state laws and the laws of several other countries, NiCd batteries must be recycled and cannot be disposed of in landfills or incinerators. Contact your local waste management agency for specific requirements and information in your area. Motorola fully endorses and encourages the recycling of NiCd batteries. In the U.
Helpful Tips Antenna Radio Operating Frequencies Before installing the antenna, make sure it matches your radio’s operating frequency. Antennas are frequency sensitive and are color coded according to their frequency range. The color code indicator is located in the center of the antenna’s base. color The following antenna types are compatible with your radio: Approx. Length in. mm Insulator Color Code 8 203 RED VHF helical 7.6 193 YELLOW 136–150.8 NAD6566 VHF helical 7 178 BLACK 150.
Helpful Tips Approx. Length in. mm Insulator Color Code 800 MHz whip, halfwave 7 178 RED 806–870 NAF5037 800 MHz dipole 8 200 RED 806–870 NAF5039 800 MHz stubby, quarterwave 3.4 86 WHITE 806–870 NAF5042 7 178 GREEN 764–870 NAF5080 Antenna Type 700/800 MHz whip 42 Frequency Range (MHz) Antenna Kit No.
Accessories Motorola provides the following approved accessories to improve the productivity of your XTS 2500 portable two-way radio. For a list of Motorola-approved antennas, batteries, and other accessories, visit the following web site which lists approved accessories: http://www.motorola.com/cgiss/index.shtml Antennas NAD6563 VHF whip (136–174 MHz) NAD6566 VHF (136–150.8 MHz) NAD6567 VHF (150.
Accessories Carry Accessories Belt Clips HLN6853 Belt clip, 2 1/4 inch Body-Worn NNTN4115 Carrying case, leather with 3-in. swivel belt loop and T-strap NNTN4116 Carrying case, leather with 2.5-in. swivel belt loop and T-strap NNTN4117 Carrying case, leather with 3-in.
Accessories NTN1667 Tri-chemistry, 110V NTN1668 Tri-Chemistry, 220V Single Unit Charger (2 Prong Euro Plug) NTN1669 Tri-chemistry, 230V NTN1873 IMPRES™ rapid charger 110V single-unit NTN1874 IMPRES™ rapid charger 220V single-unit NTN1875 IMPRES™ rapid charger 240V single-unit NTN4796 Multi-unit, tri-chemistry, rapid rate, 110V NTN7209 Single-unit dual rate, rapid charger w/o cord Enhanced and Multi-Unit Line Cords NTN7373 110V interchangeable line NTN7374 220V interchangeable line (2-pro
Accessories Surveillance Accessories CommPort® Integrated Microphone/Receivers NTN1624 CommPort with palm PTT NTN1625 CommPort ear mic with PTT for noise levels up to 100 dB (requires BDN6676 adapter) NTN1663 CommPort ear mic with ring PTT for noise levels up to 100 dB (requires BDN6676 adapter) NTN1736 CommPort ear mic with snap-on side PTT for noise levels up to 100 dB (requires BDN6676 adapter) Earpieces BDN6641 Ear mic, high noise level up to 105 dB, grey (must order BDN6671 interface module)
Accessories BDN6726 Earpiece with standard earphone, black BDN6727 Earpiece with extra-loud earphone (exceeds OSHA limits), black BDN6728 Earpiece with volume control, black BDN6729 Earpiece, mic and PTT combined, black BDN6730 Earpiece, mic and PTT separate, black BDN6731 Earpiece, mic and PTT combined, with extra-loud earphone (exceeds OSHA limits), black BDN6732 Earpiece, mic and PTT separate, with extra-loud earphone (exceeds OSHA limits), black BDN6780 Earbud, single with mic and PTT co
Accessories Radio Interface Modules for Ear Microphones BDN6671 Push-to-talk (PTT) and voice-activated (VOX) interface module (for use with BDN6641, BDN6677 and BDN6678) BDN6708 PTT interface module (for use with BDN6641, BDN6677 and BDN6678) Switches 0180300E83 Remote PTT body switch NTN7660 48 Tilt / man down switch
Appendix: Maritime Radio Use in the VHF Frequency Range Special Channel Assignments Emergency Channel If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order: 1 “MAYDAY, MAYDAY, MAYDAY.” 2 “THIS IS _____________________, CALL SIGN __________.
Appendix: Maritime Radio Use in the VHF Frequency Range Non-Commercial Call Channel For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9. Operating Frequency Requirements A radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows: • on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.
Appendix: Maritime Radio Use in the VHF Frequency Range Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Channel Number Transmit Receive 8 156.400 – 9 156.450 156.450 10 156.500 156.500 11 156.550 156.550 12 156.600 156.600 13** 156.650 156.650 14 156.700 156.700 15** 156.750 156.750 16 156.800 156.800 17** 156.850 156.850 18 156.900 161.500 19 156.950 161.550 20 157.000 161.600 * 157.050 161.650 22 157.100 161.700 * 157.150 161.750 24 157.
Appendix: Maritime Radio Use in the VHF Frequency Range Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Channel Number Transmit Receive 67** 156.375 156.375 68 156.425 156.425 69 156.475 156.475 71 156.575 156.575 72 156.625 – 73 156.675 156.675 74 156.725 156.725 75 *** *** 76 *** *** 77** 156.875 – 78 156.925 161.525 79 156.975 161.575 80 157.025 161.625 * 157.075 161.675 * 157.125 161.725 * 157.175 161.775 84 157.225 161.825 85 157.
Glossary This is a list of specialized terms used in this manual. ACK Acknowledgment of communication. Active Channel A channel that has traffic on it. Analog Signal An RF signal that has a continuous nature rather than a pulsed or discrete nature. ASTRO 25 Trunking Motorola standard for wireless digital trunked communications. ASTRO Conventional Motorola standard for wireless analog or digital conventional communications. Call Alert A page received by your radio, along with an audible tone.
Glossary Digital Private Line (DPL) A type of coded squelch using data bursts. Similar to PL except a digital code is used instead of a tone. Digital Signal An RF signal that has a pulsed, or discrete nature, rather than a continuous nature. Dispatcher An individual who has radio system management duties. Dynamic Regrouping A feature that allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other.
Glossary Non-tactical/Revert The user will talk on a preprogrammed emergency channel. The emergency alarm is sent on this same channel. Page A one-way alert, with audio messages. Personality A set of unique features specific to a radio. Preprogrammed A feature that has been assigned in advance by a qualified technician. Private Allows you to respond to a private (Conversation) Call conversation call from another radio user in the group.
Glossary Squelch Special electronic circuitry added to the receiver of a radio which reduces, or squelches, unwanted signals before they are heard in the speaker. Standby An operating condition whereby the radio’s speaker is muted but still continues to receive data. Tactical/Non-revert The user will talk on the channel that was selected before the radio entered the emergency state. Talkaround Bypass a repeater and talk directly to another unit for easy local unit-to-unit communications.
Commercial Warranty Limited Warranty MOTOROLA COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG: MOTOROLA INC.
Commercial Warranty the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. II. GENERAL PROVISIONS: This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES.
Commercial Warranty which sold you the Product, it can facilitate your obtaining warranty service. You can also call Motorola at 1-888-567-7347 US/Canada. V. WHAT THIS WARRANTY DOES NOT COVER: A) Defects or damage resulting from use of the Product in other than its normal and customary manner. B) Defects or damage from misuse, accident, water, or neglect. C) Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.
Commercial Warranty the time the Product was initially distributed from MOTOROLA. J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. K) Normal and customary wear and tear. VI.
Commercial Warranty the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such Motorola software.
Commercial Warranty Notes 62
Index A accessories antennas .................................43 batteries ..................................43 belt clips ..................................44 body-worn ...............................44 carry accessories ....................44 chargers ..................................44 Commport integrated microphone/ receivers ................................46 earpieces .................................46 headsets ..................................47 microphones, remote speaker .
Index R T radio care cleaning ...................................37 handling ...................................37 receive / transmit use the preprogrammed monitor button .....................................18 use the preprogrammed volume set button ...............................17 without using the volume set and monitor buttons ......................16 remote speaker microphone adapter 13 attach the adapter ...................13 remove the adpater .................13 repeater or direct operation ....
Motorola, Inc. 8000 West Sunrise Boulevard Ft. Lauderdale, FL 33322 MOTOROLA, the Stylized M Logo, ASTRO and CommPort are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their respective owners. © Motorola, Inc. 2004. All rights reserved. Printed in U.S.A.
