M Models RMU2080 & RMV2080
CONTENTS Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . .5 Package Contents . . . . . . . . . . . . . . . . . . . . . .5 Batteries and Chargers Safety Information . . . . . . . . . . . . . . . . . . . .7 12 12 12 14 14 15 16 CONTENTS Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 LED Indicator . . . . . . . . . . . . . . . . . . . . . Side Buttons . . . . . . . . . . . . . . . . . . . . .
CONTENTS Getting Started . . . . . . . . . . . . . . . . . . . . . .29 Turning radio ON/OFF. . . . . . . . . . . . . . . . . .29 Adjusting Volume . . . . . . . . . . . . . . . . . . . . .29 Selecting a Channel . . . . . . . . . . . . . . . . . . .29 Talking and Monitoring . . . . . . . . . . . . . . . . .29 Receiving a Call . . . . . . . . . . . . . . . . . . . . . .30 Talk Range . . . . . . . . . . . . . . . . . . . . . . . . . .30 Radio LED Indicators . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . .56 Use and Care . . . . . . . . . . . . . . . . . . . . . . .60 Frequency and Code Charts . . . . . . . . . . .61 RDX VHF Frequencies Chart . . . . . . . . . . . .61 RDV2020 - VHF Default Frequencies Chart . . . . . . . . . . . . . .63 RDV5100 - VHF Default Frequencies Chart . . . . . . . . . . . . . .64 RDX UHF Frequencies Chart . . . . . . . . . . . .65 RDU2020 - UHF Default Frequencies Chart . . . . . . . . . . . . . .
SAFETY PRODUCT SAFETY AND RF EXPOSURE COMPLIANCE ! SAFETY Caution Before using this product, read the operating instructions and RF energy awareness information contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. English 4 For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website which lists approved accessories: www.
INTRODUCTION Business Radios, RPSD 1C15, Motorola Thank you for purchasing the Motorola® R. Series Radio. This radio is a product of Motorola's 80 plus years of experience as a world leader in the designing and manufacturing of communications equipment. The RDX Series™ radios provide cost-effective communications for businesses such as retail stores, restaurants, schools, construction sites, manufacturing, property and hotel management and more.
For a copy of a large-print version of this user guide or for product-related questions, contact: 1-800-448-6686 in the USA 1-800-461-4575 in Canada 1-866-522-5210 on your TTY (Text Telephone) INTRODUCTION For product information visit us at: www.motorolasolutions.
3. and cord, pull by the plug rather than the cord when disconnecting the charger. 4. extension cord could result in risk of fire and electric shock. If an extension cord must be used, make sure that the cord size is 18AWG Before using the battery charger, read all the instructions and cautionary markings on The charger, • The battery, and • The radio using the battery 1. To reduce risk of injury, charge only the rechargeable Motorola-authorized batteries. for lengths up to 6.5 feet (2.
BATTERIES AND CHARGERS SAFETY INFORMATION English OPERATIONAL SAFETY GUIDELINES • Turn the radio OFF when charging battery. • The charger is not suitable for outdoor use. Use only in dry locations/conditions. • Connect charger only to an appropriately fused and wired supply of the correct voltage (as specified on the product). • Disconnect charger from line voltage by removing main plug. 8 • The outlet to which this equipment is connected should be nearby and easily accessible.
(FCC). To transmit on these frequencies, you FCC LICENSING INFORMATION are required to have a license issued by the FCC. Application is made available on FCC INTERFERENCE INFORMATION This device complies with Part 15 of the FCC Form 601 and Schedules D, H, and Remittance Form 159. To obtain these FCC forms, request document this device does not cause harmful 000601 which includes all forms and interference. instructions.
Before filling out your application, you must Replacement of any transmitter component decide which frequency(ies) you can operate (crystal, semiconductor, etc.) not authorized by on. See “Frequencies and Code Charts”. For the FCC equipment authorization for this radio questions on determining the radio frequency, could violate FCC rules.
RADIO OVERVIEW PARTS OF THE RADIO RADIO OVERVIEW 11 English
On/Off/Volume Knob Side Buttons Used to turn the radio ON or OFF and to adjust the radio’s volume. Push-to-Talk (PTT) Button Channel Selector Knob Used to switch the radio to different channels. Accessory Connector • Side Button 1 (SB1) • Used to connect compatible audio accessories. RADIO OVERVIEW The Side Button 1 is a general button that can be configured by the Computer Programming Software - CPS. The default setting of SB1 is ‘Monitor’.
This User Guide covers multiple RM Series models, and may detail some features your radio does not have. The radio’s model is shown at the bottom of the radio.
BATTERY FEATURES RM Series radios provide Lithium-Ion batteries that come in different capacities that will define the battery life. About the Li-Ion Battery RADIO OVERVIEW The RM Series radio comes equipped with a rechargeable Li-Ion battery. This battery should be charged before initial use to ensure optimum capacity and performance. English Battery life is determined by several factors. Among the more critical are the regular overcharge of batteries and the average depth of discharge with each cycle.
Battery Recycling and Disposal Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, access RBRC's Internet web site at: www.rbrc.com or call: 1-800-8-BATTERY This internet site and telephone number also provides other useful information concerning recycling options for consumers, businesses and governmental agencies. RADIO OVERVIEW Li-Ion rechargeable batteries can be recycled. However, recycling facilities may not be available in all areas.
Installing the Lithium-Ion (Li-Ion) Battery Removing the Lithium-Ion (Li-Ion) Battery 1. Turn OFF the radio. 2. Push down the battery latch and hold it depressed while removing the battery. RADIO OVERVIEW 3. English 1. Turn OFF the radio. 2. With the Motorola logo side up on the battery pack, fit the tabs at the bottom of the battery into the slots at the bottom of the radio’s body. 3. Press the top part of the battery towards the radio until a click is heard.
Holster Slide the radio into the base of the holster and The radio is equipped with one Drop-in Tray Charger and one Power Supply with Adaptor. For details, see “Chargers” on page 72. then press the radio against the back of the holster until the top clip is inserted in the top latch of the battery. 2. To remove, detach the top clip of the holster from the top latch of the battery and then slide the radio up from the holster. 19 RADIO OVERVIEW 1.
Battery Life Information RADIO OVERVIEW When the Battery Save feature is ON (enabled by default) the battery life will be longer.
Charging the Battery The RM series radios offers two types of Charging with the Drop-in Tray Single Unit Charger (SUC) chargers are available: • Standard Charger and, • Rapid Charger. Note: The radio comes equipped with a Standard Charger RADIO OVERVIEW To charge the battery (with the radio attached), place it in a Motorola-approved Drop-in Tray Single Unit Charger or Drop-in Tray Multi Unit Charger.
RADIO OVERVIEW To charge only the battery - at step 4, insert the battery into the tray, with the inside surface of the battery facing the front of the charger, as shown.
Drop-in Tray Charger LED Indicators Standard Charger LED Indicator LED Indicator Status Comments Waiting Yellow Flash The charger has powered up Charging Green Flash The charger is currently charging Charging Complete Steady green Battery is fully charged Battery Fault(*) Red fast flash Battery had a fault when battery was inserted Note: • (*) Normally re-seating the battery pack will correct this issue.
Estimated Charging Time The following table provides the estimated charging time of the battery. For further details, see “Battery” on page 80.
Charging a Radio and Battery using a Multi Unit Charger- MUC (Optional Accessory) Notes: • This Multi Unit Charger also allows you to clone up to 2 radios (2 Source radios and 2 Target radios). Refer to page 49 for details. • Further details on MUC’s operation are explained in the Instructions Sheet provided with the MUC. For part number details, refer to the Accessories RADIO OVERVIEW section. English The Multi Unit Charger (MUC) allows drop-in charging of up to 6 radios or batteries.
For the following explanations, refer to “Parts of the Radio” on page 11. TURNING RADIO ON/OFF To turn ON the radio, rotate the On/Off/ Volume Knob clockwise. The radio will chirp and announce the "Channel Number", also the LED Indicator will briefly blink red. To turn the radio OFF, rotate the On/Off/Volume Knob counterclockwise until you hear a ‘click’ and the radio LED Indicator turns OFF.
GETTING STARTED TALK RANGE Notes: • To listen to all activity on a current channel, short This feature is called ‘CTCSS/DPL Defeat (Squelch set to SILENT)’. • (*) This assumes SB1 is not being programmed for a different mode. Industrial Model Multi-Level Inside steel/concrete Inside multi-level Industrial buildings buildings RECEIVING A CALL UHF 2W Up to 250,000 Sq. Ft. 1. VHF 2W Up to 220,000 Sq. Ft.
1. Channel: Current channel that the radio is 4. Scramble Code: Codes that make the transmissions sound garbled to anyone listening who is not set to that specific code. For details on how to set up frequencies and CTCSS/DPL codes in the channels, refer to “Programming Selection Mode” in page 36. using, depending on radio model. 2. Frequency: The frequency the radio uses to 3. Interference Eliminator Code: These codes transmit/receive.
GETTING STARTED English RADIO LED INDICATORS 32
HANDS-FREE USE/VOX Turn the radio OFF. 2. Open accessory cover. 3. Insert the audio accessory’s plug firmly into accessory port. 4. Turn radio ON. The LED Indicator will blink double red 5. VOX Accessory Accessory Port/ Connector Motorola RM Series radios can operate hands-free (VOX) when used with compatible VOX accessories. With Compatible VOX Accessories Lower radio volume BEFORE placing accessory near ear. 6. To transmit, speak into accessory microphone GETTING STARTED 1.
GETTING STARTED Setting VOX Sensitivity Battery Save The sensitivity of the radio's accessory or microphone can be adjusted to suit different operating environments. VOX sensitivity can be programmed via the CPS. Battery Save feature extends battery life as your radio goes into ‘Idle’ state. To enable/ disable press SB1 and SB2 buttons simultaneously for 2 or 3 seconds while powering up the radio until you hear a quick series of beeps.
GETTING STARTED End of Transmission Tone (Roger Beep Tone) To enable/disable End of Transmission Tone, short press the SB1 button while turning ON the radio .
PROGRAMMING FEATURES PROGRAMMING FEATURES To easily program all the features in your radio, it is recommended to use the CPS Programming Cable and CPS software. CPS software download is available for free at www.motorolasolutions.com/RMseries PROGRAMMING MODE Programming Mode is a special radio mode to program basic radio's features by using the radio’s panel.
PROGRAMMING FEATURES English 37
Entering Programming Mode Note: Before programming the features, make sure your radio is set to the channel you wish to program.
Reading CTCSS/DPL Values If you continue short pressing the PTT button PROGRAMMING FEATURES the radio will move forward to programming CTCSS/PL Codes. English When hearing the values for CTCSS/PL Codes you can enter a new code value using SB1 and SB2 buttons. RM Series have up to 122 codes available (refer to “Frequencies and Codes Charts” Section).
Reading Auto-Scan Values After hearing the CTCSS/DPL codes, short press the PTT button and the radio will take you to Auto-Scan Auto-Scan only has two values: Each time your radio announces the current setting you can change this setting by either increasing it by short pressing SB1 or decreasing it by short pressing SB2 . The radio will then announce the new setting it has been programmed. It means AutoScan is...
• If you ‘roll-over’ to the beginning at Idle 2. code) value but the radio would not do it. number" and the LED Indicator will start blinking It rolled over and took me back to value green again. All values that were changed will be ‘0’. automatically saved. Programming Mode FAQ PROGRAMMING FEATURES 1. I got distracted while programming and forgot which feature I was programming.
4. When I was programming I made a I am done programming the features in this channel and want to program another value. How can I erase it or re-program channel. it? If you make a mistake while programming a value you have two choices: • 6. mistake and programmed the wrong The radio roll-over each time it reaches a SB1) or decreasing (short pressing SB2) until you get the desired value or, • 5. Turn OFF the radio and start-over. I just programmed the value I wanted.
• Short press the PTT button to enter Frequency Example of Programming a Code Mode. Radio will announce current value Assuming current code value is set to factory default ‘001’, and you want to change it to CTCSS/DPL Code = 103 follow the sequence below: ‘2’ • Press the SB1 button eleven times to increase frequencies and you will be hearing ferquency "13" PROGRAMMING FEATURES • Long press the PTT button. LED Indicator will show a green heartbeat to indicate 'Idle' state.
Example of Programming Auto-Scan Example of Programming Active Channels Auto-Scan is the third Programming Mode and can be set to either ON or OFF on a particular channel. Active Channels is the last Programming Mode and It allows to modify the amount of active channels in a Radio.
PROGRAMMING FEATURES OTHER PROGRAMMING FEATURES which was selected before Scan was activated. If Scan no transmission occurs within five seconds, Scan allows you to monitor other channels to detect conversations. When the radio detects a transmission, it will stop scanning and will stop on the active channel. This will allow you to listen and talk to people on that channel without having to change the channel knob.
Editing Scan List To delete a channel from the Scan List: Scan Lists can be edited by using the CPS (refer to CPS section on page 48) • Start Scan by short pressing the SB2 button (*) • Wait until the radio stops on the channel you wish to eliminate, then long press the SB2 button to Nuisance Channel Delete delete it. • The channel will not be removed until you exit Scan by short pressing the SB2 button again or by turning the radio OFF.
CPS (COMPUTER PROGRAMMING SOFTWARE) To program, connect the RM Series radio via the Drop-in Charger Tray and CPS PROGRAMMING FEATURES Programming Cable as shown in the picture above. The easiest way to program or change features in your radio is by using the Computer Programming Software (CPS) and the CPS Programming Cable(*). CPS Software is available for free as web based downloadable software at: www.motorolasolutions.
Scramble When pressing the PTT button, transmissions can be terminated by setting up a 'time-out’ timer. The Scramble feature makes transmissions sound garbled to anyone listening without the same code. Scramble default value is OFF. Power Select Reverse Burst Power Select allows you to select between high and low transmission power per frequency in each channel. The power levels for RM Series 2W toggle between 1W and 2W.
PROGRAMMING FEATURES Weather Channel English 50
Weather Channel (Cont.
CLONING RADIOS You can clone RM Series radio profiles from one Source radio to a Target radio by using any one of these 3 methods: or copied from) and • a Target radio (the radio which profile will be cloned from the source radio.
• Wait for 3 seconds before releasing the buttons until a distinctive audible tone is heard. 3. Place the Source radio in the source pocket that pairs with the target pocket you chose in step 1. Press and release SB1. PROGRAMMING FEATURES 4. After cloning is completed, the Source radio will announce either ‘pass’ (cloning was successful) When ordering the MUC, please refer to P/N PMLN6384A. Notes: • run successfully.
CPS and Cloning Cables (Optionals) • CPS Cable Both CPS and Cloning cables are made to work either with RM Series radios or RDX series. Cloning cable also can work with a mix of RDX and RM radios. • CPS cable is made to program RM series Cloning Cable radio and you have to make sure the switch is in "Flash" position. If you want to use the CPS cable to program an RDX radio, make sure the switch is in "CPS" position and attach a USB convertor provided as part of the CPS cable kit.
Cloning Radio using the Radio to Radio (R2R) Cloning Cable (Optional Accessory) 2. Unplug any cables (power supply or USB 3. Plug one side of the cloning cable mini cables) from the SUCs. connector to one SUC. Plug the other end to the second SUC. Note: 4. Turn ON the Target radio and place it into one of 5. On the Source radio, power the radio following the SUCs. the sequence below: Operating Instructions 1.
7. After cloning is completed, the Source radio will 3. Ensure that the battery is engaged properly on 4. Ensure that there is no debris in the charging 5. Ensure that the Source radio is in cloning mode. 6. Ensure that the Target radio is turned ON. 7. Ensure that radios are both from the same announce either ‘pass’ (cloning was successful) or ‘fail’ (cloning process has to the radio. failed).
Cloning using the CPS (Computer Programming Software) When cloning using this method, you will need to have the CPS software, a Drop-in Tray Charger and the CPS Programming Cable. To order the CPS Programming Cable, please refer to HKKN4028A • the CPS Help File --> Content and Index --> • in the CPS Programming Cable Accessory PROGRAMMING FEATURES Information on how to clone using the CPS is available either in: Cloning Radios, or Leaflet.
TROUBLESHOOTING Try This... Recharge Symptom or replace the Li-Ion battery. No Power Extreme operating temperatures may affect battery life. Refer to See “About the Li-Ion Battery” on page 14. Confirm Interference Eliminator Code is set. Hearing other noises or conversation on a channel Frequency or Interference Eliminator Code may be in use. Change settings: either change frequencies or codes on all radios. Make sure radio is at the right frequency and code when transmitting.
Try This... Symptom Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease range. Check for clear line of sight to improve transmission. Wearing radio close to body such as in a pocket or on a belt decreases range. Change location of radio. To increase range and coverage, you can reduce Limited talk range obstructions, increase power. UHF radios provides greater coverage in industrial and commercial buildings.
Try This... Symptom Radios are too close; they must be at least five feet apart. Heavy static or interference Radios are too far apart or obstacles are interfering with transmission. Refer to “Talking and Monitoring” on page 27. Recharge or replace Li-Ion battery. Extreme operating Low batteries temperatures affect battery life. Refer to “About the LiIon Battery” on page 14.
Try This... Symptom VOX feature might be set to OFF. Cannot activate VOX Use the CPS to ensure that the VOX Sensitivity level is not set to ‘0’. Accessory not working or not compatible. Refer to “Hands-Free Use/VOX” section on page 31. Check drop-in tray charger is properly connected and correspond to a compatible power supply.
USE AND CARE USE AND CARE Use a soft damp cloth to clean the exterior Do not immerse in water Do not use alcohol or cleaning solutions If the radio is submerged in water...
FREQUENCY AND CODE CHARTS RM VHF FREQUENCIES CHART The charts in this section provide Frequency and Code information. These charts are useful when using Motorola RM Series two-way radios with other business radios.
FREQUENCY AND CODE RM VHF Frequencies (cont.) English PLEASE NOTICE THAT THE FACTORY DEFAULT CONFIGURATION OF THE RM SERIES RADIOS HAVE BEEN MODIFIED TO BE IN COMPLIANCE WITH THE 2013 FCC NARROWBAND MANDATE. THIS MANDATE REQUIRES RADIO OPERATORS TO SWITCH THE CONFIGURATION OF THEIR EQUIPMENT TO 12.5 KHZ CHANNEL BANDWIDTH BY JANUARY 1ST, 2013. THE RM SERIES RADIO CHANNEL BANDWIDTH DEFAULT HAS BEEN SET AT 12.5 KHZ.
RMV2080 - VHF DEFAULT FREQUENCIES CHART FREQUENCY AND CODE 63 English
RM UHF FREQUENCIES CHART RM UHF Frequencies Bandwidth Frequency # Frequency (MHz) Bandwidth 1 464.5000 12.5 kHz 14 461.1625 12.5 kHz 2 464.5500 12.5 kHz 15 461.1875 12.5 kHz *3 467.7625 12.5 kHz 16 461.2125 12.5 kHz *4 467.8125 12.5 kHz 17 461.2375 12.5 kHz *5 467.8500 12.5 kHz 18 461.2625 12.5 kHz *6 467.8750 12.5 kHz 19 461.2875 12.5 kHz *7 467.9000 12.5 kHz 20 461.3125 12.5 kHz *8 467.9250 12.5 kHz 21 461.3375 12.5 kHz 9 461.0375 12.5 kHz 22 461.
FREQUENCY AND CODE RDX UHF Frequencies (Continued) English Frequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth *27 462.8625 12.5 kHz 38 466.1375 12.5 kHz *28 462.8875 12.5 kHz 39 466.1625 12.5 kHz *29 462.9125 12.5 kHz 40 466.1875 12.5 kHz 30 464.4875 12.5 kHz 41 466.2125 12.5 kHz 31 464.5125 12.5 kHz 42 466.2375 12.5 kHz 32 464.5375 12.5 kHz 43 466.2625 12.5 kHz 33 464.5625 12.5 kHz 44 466.2875 12.5 kHz 34 466.0375 12.
RM UHF Frequencies (Continued) Bandwidth Frequency # Frequency (MHz) Bandwidth *49 467.8375 12.5 kHz 61 467.1875 12.5 kHz *50 467.8625 12.5 kHz 62 467.4625 12.5 kHz *51 467.8875 12.5 kHz 63 467.4875 12.5 kHz *52 467.9125 12.5 kHz 64 467.5125 12.5 kHz 53 469.4875 12.5 kHz 65 451.1875 12.5 kHz 54 469.5125 12.5 kHz 66 451.2375 12.5 kHz 55 469.5375 12.5 kHz 67 451.2875 12.5 kHz 56 469.5625 12.5 kHz 68 451.3375 12.5 kHz 57 462.1875 12.5 kHz 69 451.4375 12.
FREQUENCY AND CODE RM UHF Frequencies (cont.) Frequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth 73 452.5375 12.5 kHz 82 456.4375 12.5 kHz 74 452.4125 12.5 kHz 83 456.5375 12.5 kHz 75 452.5125 12.5 kHz 84 456.6375 12.5 kHz 76 452.7625 12.5 kHz 85 457.3125 12.5 kHz 77 452.8625 12.5 kHz 86 457.4125 12.5 kHz 78 456.1875 12.5 kHz 87 457.5125 12.5 kHz 79 456.2375 12.5 kHz 88 457.7625 12.5 kHz 80 456.2875 12.5 kHz 89 457.8625 12.
RMU2080 - UHF DEFAULT FREQUENCIES CHART FREQUENCY AND CODE 69 English
CTCSS AND PL/DPL CODES CTCSS Codes CTCSS Hz CTCSS Hz CTCSS Hz 1 67.0 14 107.2 27 167.9 2 71.9 15 110.9 28 173.8 179.9 74.4 16 114.8 29 77.0 17 118.8 30 186.2 5 79.7 18 123 31 192.8 6 82.5 19 127.3 32 203.5 7 85.4 20 131.8 33 210.7 8 88.5 21 136.5 34 218.1 9 91.5 22 141.3 35 225.7 10 94.8 23 146.2 36 233.6 11 97.4 24 151.4 37 241.8 12 100.0 25 156.7 38 250.3 103.5 26 162.2 122 (*) 69.
PL/DPL Codes Code DPL Code DPL Code 39 23 55 116 71 243 FREQUENCY AND CODE DPL English 72 40 25 56 125 72 244 41 26 57 131 73 245 42 31 58 132 74 251 43 32 59 134 75 261 44 43 60 143 76 263 45 47 61 152 77 265 46 51 62 155 78 271 47 54 63 156 79 306 48 65 64 162 80 311 49 71 65 165 81 315 50 72 66 172 82 331 51 73 67 174 83 343 52 74 68 205 84 346 53 114 69 223 85 351 54 115 70 226 86 364
PL/DPL Codes (Continued) DPL Code DPL Code DPL Code 87 365 104 565 121 754 371 105 606 123 645 411 106 612 124 Customized PL 90 412 107 624 125 Customized PL 91 413 108 627 126 Customized PL 92 423 109 631 127 Customized PL 93 431 110 632 128 Customized PL 94 432 111 654 129 Customized PL 95 445 112 662 130 Inverted DPL 39 96 464 113 664 131 Inverted DPL 40 97 465 114 703 132 Inverted DPL 41 98 466 115 712 133 Inverted DPL 42 99 50
FREQUENCY AND CODE PL/DPL Codes (Continued) English DPL Code DPL Code DPL Code 139 Inverted DPL 48 156 Inverted DPL 65 173 Inverted DPL 82 140 Inverted DPL 49 157 Inverted DPL 66 174 Inverted DPL 83 141 Inverted DPL 50 158 Inverted DPL 67 175 Inverted DPL 84 142 Inverted DPL 51 159 Inverted DPL 68 176 Inverted DPL 85 143 Inverted DPL 52 160 Inverted DPL 69 177 Inverted DPL 86 144 Inverted DPL 53 161 Inverted DPL 70 178 Inverted DPL 87 145 Inverted DPL 54 162 I
PL/DPL Codes (Continued) Code DPL Code DPL Code 190 Inverted DPL 99 200 Inverted DPL 109 210 Inverted DPL 119 191 Inverted DPL 100 201 Inverted DPL 110 211 Inverted DPL 120 192 Inverted DPL 101 202 Inverted DPL 111 212 Inverted DPL 121 193 Inverted DPL 102 203 Inverted DPL 112 213 Inverted DPL 123 194 Inverted DPL 103 204 Inverted DPL 113 214 Customized DPL 195 Inverted DPL 104 205 Inverted DPL 114 215 Customized DPL 196 Inverted DPL 105 206 Inverted DPL 115 216
MOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADA WARRANTY What Does this Warranty Cover? English Subject to the exclusions contained below, Motorola, Inc.
Exclusions Use of Non-Motorola Products and Accessories. Defects or damage that result from the use of Non-Motorola branded or certified Products, Accessories, Software or other peripheral equipment are excluded from coverage. Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, or modification in any way by someone other than Motorola, or its authorized service centers, are excluded from coverage. Altered Products.
Communication Services. Defects, damages, or the failure of Products, Accessories or Software due to any communication service or signal you may subscribe to or use with the Products Accessories or Software is excluded from coverage. Software Products Covered Software. Applies only to physical defects in the media that embodies the copy of the software (e.g. CDROM, or floppy disk). Length of Coverage Ninety (90) days from the date of purchase. WARRANTY Software Embodied in Physical Media.
Furthermore, the purchase of the Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents, or patent applications of Motorola or any third party software provider, except for the normal, nonexclusive, royalty-free license to use that arises by operation of law in the sale of a product. PATENT NOTICE EXPORT LAW ASSURANCES This product is controlled under the export regulations of the United States of America.
ACCESSORIES ACCESSORIES AUDIO ACCESSORIES Part No. Description 53815 Headset w/Boom Mic BR HMN9026 Remote Speaker Mic BR HKLN4477 Surveillance Earpiece BR Part No.
CABLES CARRY ACCESSORIES HKLN4510A Swivel Holster SOFTWARE APPLICATIONS Part No. RVN5147 Part No. Description HKKN4028A Radio to Radio Cloning Cable HKKN4027A CPS Programming Cable CHARGERS Description Part No.
English 82 ACCESSORIES
RM Series Features Summary M 83
Programmable Via RADIO PANEL Features Display NonDisplay Programmable via CPS Display NonDisplay Default Value Programming Tips Front panel radio programming available only for Call Tones (4) Yes No Yes Yes OFF / BUTTON A Display Models by going into Programming Mode(1). Values available are 0 (OFF),1, 2 and 3. To enable/disable Call Tones press Button A (default button). Only Display Models.
Features Programmable Via RADIO PANEL Display NonDisplay Programmable via CPS Display NonDisplay Default Value Programming Tips Enables radio to enter cloning mode in order to clone its profile settings into other radios (using Cloning Mode Yes Yes Yes Yes Enable Radio to Radio Cloning Cable or Multi-Unit Charger). Press PTT, SB2 while turning radio ON. Note: You can clone radios using the CPS. This feature is referred in the CPS software as CPS Manager Lock “Codeplug Password”.
Programmable Via RADIO PANEL Features Display NonDisplay Programmable via CPS Display NonDisplay Default Value Any value within Frequencies, Direct Input (3) No No Yes Yes radio frequency Programming Tips Allows you to customize frequencies in your radio. Available only for certain 4W/5W radio models. band Radios Bandwidth is fixed and non-programmable. Bandwidth Range N/A N/A N/A N/A Model Dependant Bandwidth Range for 2W radios: VHF 150.
Features Programmable Via RADIO PANEL Programmable via CPS Default Value Display NonDisplay Display NonDisplay IVOX, sensitivity Level Yes N/A Yes N/A Keypad Beep ( or Keypad Tone) (2) Yes Yes Yes Yes ON Keypad Lock (2) Yes N/A Yes N/A UNLOCKED LEDs Enabled/ Disabled No No Yes Yes Enabled Low Battery Alert Shutdown N/A N/A N/A N/A ON HIGH (Level 3) Programming Tips Available for Display models only. Allows user to specify IVOX sensitivity level.
Programmable Via RADIO PANEL Features Display NonDisplay Programmable via CPS Display NonDisplay Default Value Programming Tips Front panel radio programming: Set radio to Maximum Channels (2) Yes Yes Yes Yes Model and CPS Programming Mode(1) to get the Maximum programmable Channels Menu option. dependant Note: Default value is set to the maximum number of channels that the radio supports.
Features Programmable Via RADIO PANEL Display NonDisplay Programmable via CPS Display NonDisplay Default Value Programming Tips Press SB2 to start scanning and wait until the radio lands on the channel you want to delete. Long press Nuisance Ch Delete (4) Yes Yes Yes Yes SB2 Button SB2 to delete the channel. Note: The nuisance deleted channel will be restored into the scan list when the radio is turned OFF or you exit SCAN. Also known as ‘Squelch defeat’.
Programmable Via RADIO PANEL Features Programmable via CPS Display NonDisplay Display NonDisplay No N/A Yes N/A Default Value Programming Tips Text that shows up in the radio display when turned Power up Text MOTOROLA ON. Default text is MOTOROLA. Programmable via CPS. Repeater/ Talkaround (3) No No Yes Yes OFF Reset to Factory Defaults (2) Yes Yes Yes Yes Enabled Reverse Burst No Programming an SBx button is needed to use this feature.
Features Scan Programmable Via RADIO PANEL Programmable via CPS Display NonDisplay Display NonDisplay Yes Yes N/A N/A Default Value SB2 Button Programming Tips Short press SB2 to enable/disable scan. Use CPS for editing Scan Lists (adding/removing Multiple (16) Scan Lists Yes No Yes Yes ON - All channels to be scanned). For display models only: Channels you can add/delete channels in the scan lists using front panel by going into Programming Mode(1).
Programmable Via RADIO PANEL Features Display NonDisplay Programmable via CPS Display NonDisplay Default Value Programming Tips Front panel radio programming available in display VOX Sensitivity Level Yes No Yes Yes OFF (level 0) models by pressing PTT or MENU buttons and scrolling down/up with and buttons to set value. Long press PTT to save. Allows to use ‘hands-free’ mode connecting microphone accessories.
New Features
Programmable Buttons Chart Notes: • Buttons come pre-programmed to default functions. Using CPS you can assign one of the features shown in the chart, so the button can toggle values using radio front panel • (*) Display models only.
Icons Chart Icon Symbol Comments Battery Level Displayed during normal radio mode operation, displays battery life remaining Channel Displayed during normal radio operation and when programming channel features Code Displayed during normal radio operation and when programming codes features Frequency Displayed during normal radio operation and when programming frequency features Keypad lock Displayed whenever the Keypad lock feature is enabled (keypad is locked) Program Displayed whenever the
Icon Symbol Comments Power Select Displayed whenever the channel is transmitting or set to a high-power selection Signal Strength RSSI Display Icon numbers of bars will indicate the strength of the received signal. Vox/IVox Displayed when IVOX/VOX enabled or when programming MIC / MIC gain features.
Notes 96
m © 2007, 2011 Motorola Solutions, Inc. All rights reserved. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners.
