User's Manual
Table Of Contents
- Introduction
- Contents
- FCC Licensing Information
- Getting Started
- 1. Slide the spring action belt clip grooves into the belt clip rails on the back of the battery pack and slide it down into place until it snaps.
- 2. To remove, push the release tab on the back of the battery surface and pull the spring action belt clip upward to remove.
- 1. With the Motorola logo side up, on the battery pack, place the battery into the radio.
- 2. Push the battery into the battery compartment to fit properly into place.
- 1. Press and hold Q to check for channel activity. If you hear static, the channel is clear to use. Do not transmit if someone is speaking on the channel. Press Q again to stop monitoring the channel.
- 2. Press and hold M and speak into the microphone. To maximize clarity, hold the radio two-to-three inches away from your mouth.
- Battery and Charging Options
- Li-Ion Battery
- Alkaline Batteries
- Charging the Radio
- Battery Life
- RDX Series Factory Defaults
- Signal Strength Indicator/Channel Busy
- Talk Range
- Hands-Free Use/VOX
- With Compatible VOX Accessories
- 1. Turn radio off.
- 2. Open accessory cover.
- 3. Insert plug of audio accessory firmly into accessory jack.
- 4. Turn radio on. Radio LED will flash double green
- 5. Lower radio volume BEFORE placing accessory near ear.
- 6. To transmit, speak into accessory microphone and to receive, stop talking.
- 7. You can disable VOX operation by pressing M or removing the audio accessory.
- Setting VOX Sensitivity
- Monitoring a Channel
- Entering Programming Mode
- Programming a Channel
- Programming the Frequency
- 1. Enter programming mode (M+SB1+hold for 3 seconds).
- 2. Selects the desired Channel (using Rotary Selector).
- 3. Press M to move to the "Tens Digit" of Frequency, then scroll up or down using SB1/SB2 to set the "10's" value.
- 4. Press M to move to "Units Digit" of Frequency, then scroll up or down using SB1/SB2 to set the "1's" value.
- Programming the Interference Eliminator Code
- 1. Press M to move to the "Hundreds Digit" of Code, then scroll up or down using SB1/SB2 to set the "100's" value.
- 2. Press M to move to the "Tens Digit" of Code, then scroll up or down using SB1/SB2 to set the "10's" value.
- 3. Press M to move to the "Units Digit" of Code, then scroll up or down using SB1/ SB2 to set the "1s" value.
- Programming Bandwidth (when FCC allowable)
- Programming Call Tones
- Programming Microphone Gain
- Cloning
- Frequencies and Bandwidths
- 1
- 151.6250
- 25.00
- 16
- 151.8650
- 25.00
- 2
- 151.9550
- 25.00
- 17
- 151.8950
- 25.00
- 3
- 154.5700
- 25.00
- 18
- 151.9250
- 25.00
- 4
- 154.6000
- 25.00
- 19
- 152.7000
- 25.00
- 5
- 151.7000
- 12.5/25.0
- 20
- 154.4900
- 25.00
- 6
- 151.7600
- 12.5/25.0
- 21
- 154.5150
- 25.00
- *7
- 151.8200
- 12.5/25.0
- 22
- 154.5275
- 25.00
- *8
- 151.8800
- 12.5/25.0
- 23
- 154.5400
- 25.00
- *9
- 151.9400
- 12.5/25.0
- 24
- 154.6000
- 25.00
- 10
- 151.5125
- 25.00
- 25
- 154.6550
- 25.00
- 11
- 151.6550
- 25.00
- 26
- 158.4000
- 25.00
- 12
- 151.6850
- 25.00
- 27
- 158.4075
- 25.00
- 13
- 151.7150
- 25.00
- 14
- 151.7450
- 25.00
- 15
- 151.7750
- 25.00
- Getting Started
- UHF Frequencies
- 1
- 464.5000
- 12.5/25.0
- 15
- 461.1875
- 12.5
- 2
- 464.5500
- 12.5/25.0
- 16
- 461.2125
- 12.5
- 3
- 467.7625
- 12.5/25.0
- 17
- 461.2375
- 12.5
- 4
- 467.8125
- 12.5/25.0
- 18
- 461.2625
- 12.5
- 5
- 467.8500
- 12.5/25.0
- 19
- 461.2875
- 12.5
- 6
- 467.8750
- 12.5/25.0
- 20
- 461.3125
- 12.5
- 7
- 467.9000
- 12.5/25.0
- 21
- 461.3375
- 12.5
- 8
- 467.9250
- 12.5/25.0
- 22
- 461.3625
- 12.5
- 9
- 461.0375
- 12.5
- 23
- 462.7625
- 12.5
- 10
- 461.0625
- 12.5
- 24
- 462.7875
- 12.5
- 11
- 461.0875
- 12.5
- 25
- 462.8125
- 12.5
- 12
- 461.1125
- 12.5
- 26
- 462.8375
- 12.5
- 13
- 461.1375
- 12.5
- 27
- 462.8625
- 12.5
- 14
- 461.1625
- 12.5
- 28
- 462.8875
- 12.5
- 29
- 462.9125
- 12.5
- 43
- 466.2625
- 12.5
- 30
- 464.4875
- 12.5
- 44
- 466.2875
- 12.5
- 31
- 464.5125
- 12.5
- 45
- 466.3125
- 12.5
- 32
- 464.5375
- 12.5
- 46
- 466.3375
- 12.5
- 33
- 464.5625
- 12.5
- 47
- 466.3625
- 12.5
- 34
- 466.0375
- 12.5
- 48
- 467.7875
- 12.5
- 35
- 466.0625
- 12.5
- 49
- 467.8375
- 12.5
- 36
- 466.0875
- 12.5
- 50
- 467.8625
- 12.5
- 37
- 466.1125
- 12.5
- 51
- 467.8875
- 12.5
- 38
- 466.1375
- 12.5
- 52
- 467.9125
- 12.5
- 39
- 466.1625
- 12.5
- 53
- 469.4875
- 12.5
- 40
- 466.1875
- 12.5
- 54
- 469.5125
- 12.5
- 41
- 466.2125
- 12.5
- 55
- 469.5375
- 12.5
- 42
- 466.2375
- 12.5
- 56
- 469.5625
- 12.5
- UHF Frequencies (Continued)
- 57
- 462.1875
- 12.5
- 71
- 451.6375
- 12.5
- 58
- 462.4625
- 12.5
- 72
- 452.3125
- 12.5
- 59
- 462.4875
- 12.5
- 73
- 452.5375
- 12.5
- 60
- 462.5125
- 12.5
- 74
- 452.4125
- 12.5
- 61
- 467.1875
- 12.5
- 75
- 452.5125
- 12.5
- 62
- 467.4625
- 12.5
- 76
- 452.7625
- 12.5
- 63
- 467.4875
- 12.5
- 77
- 452.8625
- 12.5
- 64
- 467.5125
- 12.5
- 78
- 456.1875
- 12.5
- 65
- 451.1875
- 12.5
- 79
- 456.2375
- 12.5
- 66
- 451.2375
- 12.5
- 80
- 456.2875
- 12.5
- 67
- 451.2875
- 12.5
- 81
- 456.3375
- 12.5
- 68
- 451.3375
- 12.5
- 82
- 456.4375
- 12.5
- 69
- 451.4375
- 12.5
- 83
- 456.5375
- 12.5
- 70
- 451.5375
- 12.5
- 84
- 456.6375
- 12.5
- 85
- 457.3125
- 12.5
- 88
- 457.7625
- 12.5
- 86
- 457.4125
- 12.5
- 89
- 457.8625
- 12.5
- 87
- 457.5125
- 12.5
- -
- -
- -
- Interference Eliminator Codes
- Digital Interference Eliminator Codes
Use and Care
42
RDX
UHF Frequencies (Continued)
Programmi
ng Number
Frequency
(MHz)
Bandwidth
Programmi
ng Number
Frequency
(MHz)
Bandwidth
57 462.1875 12.5 71 451.6375 12.5
58 462.4625 12.5
72 452.3125 12.5
59 462.4875 12.5
73 452.5375 12.5
60 462.5125 12.5
74 452.4125 12.5
61 467.1875 12.5
75 452.5125 12.5
62 467.4625 12.5
76 452.7625 12.5
63 467.4875 12.5
77 452.8625 12.5
64 467.5125 12.5
78 456.1875 12.5
65 451.1875 12.5
79 456.2375 12.5
66 451.2375 12.5
80 456.2875 12.5
67 451.2875 12.5
81 456.3375 12.5
68 451.3375 12.5
82 456.4375 12.5
69 451.4375 12.5
83 456.5375 12.5
70 451.5375 12.5
84 456.6375 12.5
6864110R04b.book Page 42 Friday, October 20, 2006 4:38 PM