User's Manual
Table Of Contents
- Introduction
- Contents
- FCC Licensing Information
- Getting Started
- 1. Slide the spring action belt clip grooves into the belt clip rails on the back of the battery pack and slide it down into place until it snaps.
- 2. To remove, push the release tab on the back of the battery surface and pull the spring action belt clip upward to remove.
- 1. With the Motorola logo side up, on the battery pack, place the battery into the radio.
- 2. Push the battery into the battery compartment to fit properly into place.
- 1. Press and hold Q to check for channel activity. If you hear static, the channel is clear to use. Do not transmit if someone is speaking on the channel. Press Q again to stop monitoring the channel.
- 2. Press and hold M and speak into the microphone. To maximize clarity, hold the radio two-to-three inches away from your mouth.
- Battery and Charging Options
- Li-Ion Battery
- Alkaline Batteries
- Charging the Radio
- Battery Life
- RDX Series Factory Defaults
- Signal Strength Indicator/Channel Busy
- Talk Range
- Hands-Free Use/VOX
- With Compatible VOX Accessories
- 1. Turn radio off.
- 2. Open accessory cover.
- 3. Insert plug of audio accessory firmly into accessory jack.
- 4. Turn radio on. Radio LED will flash double green
- 5. Lower radio volume BEFORE placing accessory near ear.
- 6. To transmit, speak into accessory microphone and to receive, stop talking.
- 7. You can disable VOX operation by pressing M or removing the audio accessory.
- Setting VOX Sensitivity
- Monitoring a Channel
- Entering Programming Mode
- Programming a Channel
- Programming the Frequency
- 1. Enter programming mode (M+SB1+hold for 3 seconds).
- 2. Selects the desired Channel (using Rotary Selector).
- 3. Press M to move to the "Tens Digit" of Frequency, then scroll up or down using SB1/SB2 to set the "10's" value.
- 4. Press M to move to "Units Digit" of Frequency, then scroll up or down using SB1/SB2 to set the "1's" value.
- Programming the Interference Eliminator Code
- 1. Press M to move to the "Hundreds Digit" of Code, then scroll up or down using SB1/SB2 to set the "100's" value.
- 2. Press M to move to the "Tens Digit" of Code, then scroll up or down using SB1/SB2 to set the "10's" value.
- 3. Press M to move to the "Units Digit" of Code, then scroll up or down using SB1/ SB2 to set the "1s" value.
- Programming Bandwidth (when FCC allowable)
- Programming Call Tones
- Programming Microphone Gain
- Cloning
- Frequencies and Bandwidths
- 1
- 151.6250
- 25.00
- 16
- 151.8650
- 25.00
- 2
- 151.9550
- 25.00
- 17
- 151.8950
- 25.00
- 3
- 154.5700
- 25.00
- 18
- 151.9250
- 25.00
- 4
- 154.6000
- 25.00
- 19
- 152.7000
- 25.00
- 5
- 151.7000
- 12.5/25.0
- 20
- 154.4900
- 25.00
- 6
- 151.7600
- 12.5/25.0
- 21
- 154.5150
- 25.00
- *7
- 151.8200
- 12.5/25.0
- 22
- 154.5275
- 25.00
- *8
- 151.8800
- 12.5/25.0
- 23
- 154.5400
- 25.00
- *9
- 151.9400
- 12.5/25.0
- 24
- 154.6000
- 25.00
- 10
- 151.5125
- 25.00
- 25
- 154.6550
- 25.00
- 11
- 151.6550
- 25.00
- 26
- 158.4000
- 25.00
- 12
- 151.6850
- 25.00
- 27
- 158.4075
- 25.00
- 13
- 151.7150
- 25.00
- 14
- 151.7450
- 25.00
- 15
- 151.7750
- 25.00
- Getting Started
- UHF Frequencies
- 1
- 464.5000
- 12.5/25.0
- 15
- 461.1875
- 12.5
- 2
- 464.5500
- 12.5/25.0
- 16
- 461.2125
- 12.5
- 3
- 467.7625
- 12.5/25.0
- 17
- 461.2375
- 12.5
- 4
- 467.8125
- 12.5/25.0
- 18
- 461.2625
- 12.5
- 5
- 467.8500
- 12.5/25.0
- 19
- 461.2875
- 12.5
- 6
- 467.8750
- 12.5/25.0
- 20
- 461.3125
- 12.5
- 7
- 467.9000
- 12.5/25.0
- 21
- 461.3375
- 12.5
- 8
- 467.9250
- 12.5/25.0
- 22
- 461.3625
- 12.5
- 9
- 461.0375
- 12.5
- 23
- 462.7625
- 12.5
- 10
- 461.0625
- 12.5
- 24
- 462.7875
- 12.5
- 11
- 461.0875
- 12.5
- 25
- 462.8125
- 12.5
- 12
- 461.1125
- 12.5
- 26
- 462.8375
- 12.5
- 13
- 461.1375
- 12.5
- 27
- 462.8625
- 12.5
- 14
- 461.1625
- 12.5
- 28
- 462.8875
- 12.5
- 29
- 462.9125
- 12.5
- 43
- 466.2625
- 12.5
- 30
- 464.4875
- 12.5
- 44
- 466.2875
- 12.5
- 31
- 464.5125
- 12.5
- 45
- 466.3125
- 12.5
- 32
- 464.5375
- 12.5
- 46
- 466.3375
- 12.5
- 33
- 464.5625
- 12.5
- 47
- 466.3625
- 12.5
- 34
- 466.0375
- 12.5
- 48
- 467.7875
- 12.5
- 35
- 466.0625
- 12.5
- 49
- 467.8375
- 12.5
- 36
- 466.0875
- 12.5
- 50
- 467.8625
- 12.5
- 37
- 466.1125
- 12.5
- 51
- 467.8875
- 12.5
- 38
- 466.1375
- 12.5
- 52
- 467.9125
- 12.5
- 39
- 466.1625
- 12.5
- 53
- 469.4875
- 12.5
- 40
- 466.1875
- 12.5
- 54
- 469.5125
- 12.5
- 41
- 466.2125
- 12.5
- 55
- 469.5375
- 12.5
- 42
- 466.2375
- 12.5
- 56
- 469.5625
- 12.5
- UHF Frequencies (Continued)
- 57
- 462.1875
- 12.5
- 71
- 451.6375
- 12.5
- 58
- 462.4625
- 12.5
- 72
- 452.3125
- 12.5
- 59
- 462.4875
- 12.5
- 73
- 452.5375
- 12.5
- 60
- 462.5125
- 12.5
- 74
- 452.4125
- 12.5
- 61
- 467.1875
- 12.5
- 75
- 452.5125
- 12.5
- 62
- 467.4625
- 12.5
- 76
- 452.7625
- 12.5
- 63
- 467.4875
- 12.5
- 77
- 452.8625
- 12.5
- 64
- 467.5125
- 12.5
- 78
- 456.1875
- 12.5
- 65
- 451.1875
- 12.5
- 79
- 456.2375
- 12.5
- 66
- 451.2375
- 12.5
- 80
- 456.2875
- 12.5
- 67
- 451.2875
- 12.5
- 81
- 456.3375
- 12.5
- 68
- 451.3375
- 12.5
- 82
- 456.4375
- 12.5
- 69
- 451.4375
- 12.5
- 83
- 456.5375
- 12.5
- 70
- 451.5375
- 12.5
- 84
- 456.6375
- 12.5
- 85
- 457.3125
- 12.5
- 88
- 457.7625
- 12.5
- 86
- 457.4125
- 12.5
- 89
- 457.8625
- 12.5
- 87
- 457.5125
- 12.5
- -
- -
- -
- Interference Eliminator Codes
- Digital Interference Eliminator Codes
Programming Features
30
RDX
Programming Bandwidth (when FCC allowable)
Some frequencies have selectable channel spacing, which must
match other radios for optimal radio quality. Bandwidth settings are
programmed for each channel.
1. Enter Programming Mode as necessary, refer to “Entering
Programming Mode” on page 28.
Note: Spirit GT radios operate at 12.5 kHz. The M Series radios may operate at
25.0 kHz or 12.5 kHz bandwidth if selectable. If you have questions on radio
use, call 1-800-448-6686.
Programming Call Tones
Your radio can transmit call tones to other radios in your group so
you can alert them that you are about to talk. The default is set to 0
(off) or you may choose 1
,
2,
or
3 to choose a distinctive call tone.
1. Enter Programming Mode as necessary, refer to “Entering
Programming Mode” on page 28.
Programming Microphone Gain
The sensitivity of your radio’s microphone can be adjusted to suit different users or
operating environments.
1. Enter Programming Mode as necessary, refer to “Entering Programming Mode”
on page 28.
6864110R04b.book Page 30 Friday, October 20, 2006 4:38 PM