User's Manual
Table Of Contents
- Introduction
- Contents
- FCC Licensing Information
- Getting Started
- 1. Slide the spring action belt clip grooves into the belt clip rails on the back of the battery pack and slide it down into place until it snaps.
- 2. To remove, push the release tab on the back of the battery surface and pull the spring action belt clip upward to remove.
- 1. With the Motorola logo side up, on the battery pack, place the battery into the radio.
- 2. Push the battery into the battery compartment to fit properly into place.
- 1. Press and hold Q to check for channel activity. If you hear static, the channel is clear to use. Do not transmit if someone is speaking on the channel. Press Q again to stop monitoring the channel.
- 2. Press and hold M and speak into the microphone. To maximize clarity, hold the radio two-to-three inches away from your mouth.
- Battery and Charging Options
- Li-Ion Battery
- Alkaline Batteries
- Charging the Radio
- Battery Life
- RDX Series Factory Defaults
- Signal Strength Indicator/Channel Busy
- Talk Range
- Hands-Free Use/VOX
- With Compatible VOX Accessories
- 1. Turn radio off.
- 2. Open accessory cover.
- 3. Insert plug of audio accessory firmly into accessory jack.
- 4. Turn radio on. Radio LED will flash double green
- 5. Lower radio volume BEFORE placing accessory near ear.
- 6. To transmit, speak into accessory microphone and to receive, stop talking.
- 7. You can disable VOX operation by pressing M or removing the audio accessory.
- Setting VOX Sensitivity
- Monitoring a Channel
- Entering Programming Mode
- Programming a Channel
- Programming the Frequency
- 1. Enter programming mode (M+SB1+hold for 3 seconds).
- 2. Selects the desired Channel (using Rotary Selector).
- 3. Press M to move to the "Tens Digit" of Frequency, then scroll up or down using SB1/SB2 to set the "10's" value.
- 4. Press M to move to "Units Digit" of Frequency, then scroll up or down using SB1/SB2 to set the "1's" value.
- Programming the Interference Eliminator Code
- 1. Press M to move to the "Hundreds Digit" of Code, then scroll up or down using SB1/SB2 to set the "100's" value.
- 2. Press M to move to the "Tens Digit" of Code, then scroll up or down using SB1/SB2 to set the "10's" value.
- 3. Press M to move to the "Units Digit" of Code, then scroll up or down using SB1/ SB2 to set the "1s" value.
- Programming Bandwidth (when FCC allowable)
- Programming Call Tones
- Programming Microphone Gain
- Cloning
- Frequencies and Bandwidths
- 1
- 151.6250
- 25.00
- 16
- 151.8650
- 25.00
- 2
- 151.9550
- 25.00
- 17
- 151.8950
- 25.00
- 3
- 154.5700
- 25.00
- 18
- 151.9250
- 25.00
- 4
- 154.6000
- 25.00
- 19
- 152.7000
- 25.00
- 5
- 151.7000
- 12.5/25.0
- 20
- 154.4900
- 25.00
- 6
- 151.7600
- 12.5/25.0
- 21
- 154.5150
- 25.00
- *7
- 151.8200
- 12.5/25.0
- 22
- 154.5275
- 25.00
- *8
- 151.8800
- 12.5/25.0
- 23
- 154.5400
- 25.00
- *9
- 151.9400
- 12.5/25.0
- 24
- 154.6000
- 25.00
- 10
- 151.5125
- 25.00
- 25
- 154.6550
- 25.00
- 11
- 151.6550
- 25.00
- 26
- 158.4000
- 25.00
- 12
- 151.6850
- 25.00
- 27
- 158.4075
- 25.00
- 13
- 151.7150
- 25.00
- 14
- 151.7450
- 25.00
- 15
- 151.7750
- 25.00
- Getting Started
- UHF Frequencies
- 1
- 464.5000
- 12.5/25.0
- 15
- 461.1875
- 12.5
- 2
- 464.5500
- 12.5/25.0
- 16
- 461.2125
- 12.5
- 3
- 467.7625
- 12.5/25.0
- 17
- 461.2375
- 12.5
- 4
- 467.8125
- 12.5/25.0
- 18
- 461.2625
- 12.5
- 5
- 467.8500
- 12.5/25.0
- 19
- 461.2875
- 12.5
- 6
- 467.8750
- 12.5/25.0
- 20
- 461.3125
- 12.5
- 7
- 467.9000
- 12.5/25.0
- 21
- 461.3375
- 12.5
- 8
- 467.9250
- 12.5/25.0
- 22
- 461.3625
- 12.5
- 9
- 461.0375
- 12.5
- 23
- 462.7625
- 12.5
- 10
- 461.0625
- 12.5
- 24
- 462.7875
- 12.5
- 11
- 461.0875
- 12.5
- 25
- 462.8125
- 12.5
- 12
- 461.1125
- 12.5
- 26
- 462.8375
- 12.5
- 13
- 461.1375
- 12.5
- 27
- 462.8625
- 12.5
- 14
- 461.1625
- 12.5
- 28
- 462.8875
- 12.5
- 29
- 462.9125
- 12.5
- 43
- 466.2625
- 12.5
- 30
- 464.4875
- 12.5
- 44
- 466.2875
- 12.5
- 31
- 464.5125
- 12.5
- 45
- 466.3125
- 12.5
- 32
- 464.5375
- 12.5
- 46
- 466.3375
- 12.5
- 33
- 464.5625
- 12.5
- 47
- 466.3625
- 12.5
- 34
- 466.0375
- 12.5
- 48
- 467.7875
- 12.5
- 35
- 466.0625
- 12.5
- 49
- 467.8375
- 12.5
- 36
- 466.0875
- 12.5
- 50
- 467.8625
- 12.5
- 37
- 466.1125
- 12.5
- 51
- 467.8875
- 12.5
- 38
- 466.1375
- 12.5
- 52
- 467.9125
- 12.5
- 39
- 466.1625
- 12.5
- 53
- 469.4875
- 12.5
- 40
- 466.1875
- 12.5
- 54
- 469.5125
- 12.5
- 41
- 466.2125
- 12.5
- 55
- 469.5375
- 12.5
- 42
- 466.2375
- 12.5
- 56
- 469.5625
- 12.5
- UHF Frequencies (Continued)
- 57
- 462.1875
- 12.5
- 71
- 451.6375
- 12.5
- 58
- 462.4625
- 12.5
- 72
- 452.3125
- 12.5
- 59
- 462.4875
- 12.5
- 73
- 452.5375
- 12.5
- 60
- 462.5125
- 12.5
- 74
- 452.4125
- 12.5
- 61
- 467.1875
- 12.5
- 75
- 452.5125
- 12.5
- 62
- 467.4625
- 12.5
- 76
- 452.7625
- 12.5
- 63
- 467.4875
- 12.5
- 77
- 452.8625
- 12.5
- 64
- 467.5125
- 12.5
- 78
- 456.1875
- 12.5
- 65
- 451.1875
- 12.5
- 79
- 456.2375
- 12.5
- 66
- 451.2375
- 12.5
- 80
- 456.2875
- 12.5
- 67
- 451.2875
- 12.5
- 81
- 456.3375
- 12.5
- 68
- 451.3375
- 12.5
- 82
- 456.4375
- 12.5
- 69
- 451.4375
- 12.5
- 83
- 456.5375
- 12.5
- 70
- 451.5375
- 12.5
- 84
- 456.6375
- 12.5
- 85
- 457.3125
- 12.5
- 88
- 457.7625
- 12.5
- 86
- 457.4125
- 12.5
- 89
- 457.8625
- 12.5
- 87
- 457.5125
- 12.5
- -
- -
- -
- Interference Eliminator Codes
- Digital Interference Eliminator Codes
Safety and General Information
15
charged battery, particularly when placing it inside
a pocket, purse, or other container with metal
objects.
INTRINSICALLY SAFE RADIO
INFORMATION
The Intrinsically safe approval unit refers to a
product that has been approved as intrinsically
safe by an approval agency (for example FM
Approvals, CSA, UL, CENELEC or ATEX) and
certifies that a particular product meets the
Agency's applicable intrinsic safety standards for
specific types of hazardous classified locations. A
portable radio that has been approved for intrinsic
safety will have Approval label attached to the radio
to identify the unit as being Approved for specified
hazardous atmospheres. This label specifies the
hazardous Class/Division/Group along with the
part number of the battery that must be used. The
Intrinsically Safe Approval Label will be located on
the portable radio unit.
Operational Cautions for Intrinsic Safe
Equipment
• Do not operate radio communications equipment
in a hazardous atmosphere unless it is a type
especially qualified (for example, FM, UL, CSA, or
CENELEC or ATEX approved). An explosion or
fire may result.
• Do not operate a radio unit that has been
approved as intrinsically safe product in a hazard-
ous atmosphere if it has been physically damaged
(for example, cracked housing). An explosion or
fire may result.
Do not replace or charge batteries in a hazardous
atmosphere. Contact sparking may occur while
installing or removing batteries and cause an
explosion or fire.
Warnings for Radios
Approved as Intrinsically Safe
Radios must ship from the Motorola
manufacturing facility with the
hazardous atmosphere capability
and the intrinsic safety approval labelling (FM, UL,
CSA, CENELEC or ATEX). Radios will not be
upgraded to this capability and labeled once they
have been shipped to the field. A modification
changes the unit’s hardware from it’s original
design made by the original product.
• Do not replace or change accessories in a
hazardous atmosphere. Contact sparking
may occur while installing or removing
accessories and cause an explosion or fire.
• Turn the radio off before removing or
installing a battery or accessory.
• Do not disassemble an intrinsically safe
product in any way that exposes the
internal circuits of the unit.
• Failure to use an intrinsically safe approved
battery or Approved accessories
specifically approved for the radio unit may
!
WARNING
6864110R04b.book Page 15 Friday, October 20, 2006 4:38 PM