User's Manual
Table Of Contents
- Introduction
- Contents
- FCC Licensing Information
- Getting Started
- 1. Slide the spring action belt clip grooves into the belt clip rails on the back of the battery pack and slide it down into place until it snaps.
- 2. To remove, push the release tab on the back of the battery surface and pull the spring action belt clip upward to remove.
- 1. With the Motorola logo side up, on the battery pack, place the battery into the radio.
- 2. Push the battery into the battery compartment to fit properly into place.
- 1. Press and hold Q to check for channel activity. If you hear static, the channel is clear to use. Do not transmit if someone is speaking on the channel. Press Q again to stop monitoring the channel.
- 2. Press and hold M and speak into the microphone. To maximize clarity, hold the radio two-to-three inches away from your mouth.
- Battery and Charging Options
- Li-Ion Battery
- Alkaline Batteries
- Charging the Radio
- Battery Life
- RDX Series Factory Defaults
- Signal Strength Indicator/Channel Busy
- Talk Range
- Hands-Free Use/VOX
- With Compatible VOX Accessories
- 1. Turn radio off.
- 2. Open accessory cover.
- 3. Insert plug of audio accessory firmly into accessory jack.
- 4. Turn radio on. Radio LED will flash double green
- 5. Lower radio volume BEFORE placing accessory near ear.
- 6. To transmit, speak into accessory microphone and to receive, stop talking.
- 7. You can disable VOX operation by pressing M or removing the audio accessory.
- Setting VOX Sensitivity
- Monitoring a Channel
- Entering Programming Mode
- Programming a Channel
- Programming the Frequency
- 1. Enter programming mode (M+SB1+hold for 3 seconds).
- 2. Selects the desired Channel (using Rotary Selector).
- 3. Press M to move to the "Tens Digit" of Frequency, then scroll up or down using SB1/SB2 to set the "10's" value.
- 4. Press M to move to "Units Digit" of Frequency, then scroll up or down using SB1/SB2 to set the "1's" value.
- Programming the Interference Eliminator Code
- 1. Press M to move to the "Hundreds Digit" of Code, then scroll up or down using SB1/SB2 to set the "100's" value.
- 2. Press M to move to the "Tens Digit" of Code, then scroll up or down using SB1/SB2 to set the "10's" value.
- 3. Press M to move to the "Units Digit" of Code, then scroll up or down using SB1/ SB2 to set the "1s" value.
- Programming Bandwidth (when FCC allowable)
- Programming Call Tones
- Programming Microphone Gain
- Cloning
- Frequencies and Bandwidths
- 1
- 151.6250
- 25.00
- 16
- 151.8650
- 25.00
- 2
- 151.9550
- 25.00
- 17
- 151.8950
- 25.00
- 3
- 154.5700
- 25.00
- 18
- 151.9250
- 25.00
- 4
- 154.6000
- 25.00
- 19
- 152.7000
- 25.00
- 5
- 151.7000
- 12.5/25.0
- 20
- 154.4900
- 25.00
- 6
- 151.7600
- 12.5/25.0
- 21
- 154.5150
- 25.00
- *7
- 151.8200
- 12.5/25.0
- 22
- 154.5275
- 25.00
- *8
- 151.8800
- 12.5/25.0
- 23
- 154.5400
- 25.00
- *9
- 151.9400
- 12.5/25.0
- 24
- 154.6000
- 25.00
- 10
- 151.5125
- 25.00
- 25
- 154.6550
- 25.00
- 11
- 151.6550
- 25.00
- 26
- 158.4000
- 25.00
- 12
- 151.6850
- 25.00
- 27
- 158.4075
- 25.00
- 13
- 151.7150
- 25.00
- 14
- 151.7450
- 25.00
- 15
- 151.7750
- 25.00
- Getting Started
- UHF Frequencies
- 1
- 464.5000
- 12.5/25.0
- 15
- 461.1875
- 12.5
- 2
- 464.5500
- 12.5/25.0
- 16
- 461.2125
- 12.5
- 3
- 467.7625
- 12.5/25.0
- 17
- 461.2375
- 12.5
- 4
- 467.8125
- 12.5/25.0
- 18
- 461.2625
- 12.5
- 5
- 467.8500
- 12.5/25.0
- 19
- 461.2875
- 12.5
- 6
- 467.8750
- 12.5/25.0
- 20
- 461.3125
- 12.5
- 7
- 467.9000
- 12.5/25.0
- 21
- 461.3375
- 12.5
- 8
- 467.9250
- 12.5/25.0
- 22
- 461.3625
- 12.5
- 9
- 461.0375
- 12.5
- 23
- 462.7625
- 12.5
- 10
- 461.0625
- 12.5
- 24
- 462.7875
- 12.5
- 11
- 461.0875
- 12.5
- 25
- 462.8125
- 12.5
- 12
- 461.1125
- 12.5
- 26
- 462.8375
- 12.5
- 13
- 461.1375
- 12.5
- 27
- 462.8625
- 12.5
- 14
- 461.1625
- 12.5
- 28
- 462.8875
- 12.5
- 29
- 462.9125
- 12.5
- 43
- 466.2625
- 12.5
- 30
- 464.4875
- 12.5
- 44
- 466.2875
- 12.5
- 31
- 464.5125
- 12.5
- 45
- 466.3125
- 12.5
- 32
- 464.5375
- 12.5
- 46
- 466.3375
- 12.5
- 33
- 464.5625
- 12.5
- 47
- 466.3625
- 12.5
- 34
- 466.0375
- 12.5
- 48
- 467.7875
- 12.5
- 35
- 466.0625
- 12.5
- 49
- 467.8375
- 12.5
- 36
- 466.0875
- 12.5
- 50
- 467.8625
- 12.5
- 37
- 466.1125
- 12.5
- 51
- 467.8875
- 12.5
- 38
- 466.1375
- 12.5
- 52
- 467.9125
- 12.5
- 39
- 466.1625
- 12.5
- 53
- 469.4875
- 12.5
- 40
- 466.1875
- 12.5
- 54
- 469.5125
- 12.5
- 41
- 466.2125
- 12.5
- 55
- 469.5375
- 12.5
- 42
- 466.2375
- 12.5
- 56
- 469.5625
- 12.5
- UHF Frequencies (Continued)
- 57
- 462.1875
- 12.5
- 71
- 451.6375
- 12.5
- 58
- 462.4625
- 12.5
- 72
- 452.3125
- 12.5
- 59
- 462.4875
- 12.5
- 73
- 452.5375
- 12.5
- 60
- 462.5125
- 12.5
- 74
- 452.4125
- 12.5
- 61
- 467.1875
- 12.5
- 75
- 452.5125
- 12.5
- 62
- 467.4625
- 12.5
- 76
- 452.7625
- 12.5
- 63
- 467.4875
- 12.5
- 77
- 452.8625
- 12.5
- 64
- 467.5125
- 12.5
- 78
- 456.1875
- 12.5
- 65
- 451.1875
- 12.5
- 79
- 456.2375
- 12.5
- 66
- 451.2375
- 12.5
- 80
- 456.2875
- 12.5
- 67
- 451.2875
- 12.5
- 81
- 456.3375
- 12.5
- 68
- 451.3375
- 12.5
- 82
- 456.4375
- 12.5
- 69
- 451.4375
- 12.5
- 83
- 456.5375
- 12.5
- 70
- 451.5375
- 12.5
- 84
- 456.6375
- 12.5
- 85
- 457.3125
- 12.5
- 88
- 457.7625
- 12.5
- 86
- 457.4125
- 12.5
- 89
- 457.8625
- 12.5
- 87
- 457.5125
- 12.5
- -
- -
- -
- Interference Eliminator Codes
- Digital Interference Eliminator Codes
Safety and General Inforation
12
a Motorola-approved clip, holder, holster, case, or
body harness for this product. Using approved
body-worn accessories is important because the
use of non-Motorola-approved accessories may
result in exposure levels, which exceed the IEEE/
ICNIRP occupational/controlled environment RF
exposure limits.
• If you are not using a body-worn accessory and
are not using the radio in the intended use posi-
tion, along side the head in the phone mode
(TETRA only), in front of the face in the hand
held mode, then ensure the antenna and the
radio are kept 2.5 cm (one inch) from the body
when transmitting.
Keeping the radio at a
proper distance is important because RF expo-
sures decrease with increasing distance from
the antenna.
Hand-held Mode - Operating Instructions
• Hold the radio in a vertical position in
front of the face with the microphone
(and other parts of the radio includ-
ing the antenna) at least 2.5 cm (one
inch) away from the nose or lips.
Antenna should be kept away from the eye. Keep-
ing the radio at a proper distance is important
since RF exposures decrease with increasing dis-
tance from the antenna.
Phone Mode (TETRA only) - Operating
Instructions
• When placing or receiving a phone call, hold
your radio product as you would a wireless
telephone. Speak directly into the microphone.
Approved Accessories
• Use only Motorola-approved supplied or replace-
ment antennas, batteries, and accessories. Use of
non–Motorola - approved antennas, batteries and
accessories may exceed IEEE/ICNIRP RF expo-
sure guidelines.
For a list of Motorola-approved accessories, visit
the following website, which lists approved acces-
sories for your radio model.
http://www.motorola.com/governmentandenterprise
Additional Information
For additional information on exposure
requirements or other training information, visit
http://www.motorola.com/rfhealth.
Electromagnetic Interference/
Compatibility
NOTE: Nearly every electronic device is
susceptible to electromagnetic interference (EMI) if
inadequately shielded, designed or otherwise
configured for electromagnetic compatibility.
MAN WITH RADI
O
6864110R04b.book Page 12 Friday, October 20, 2006 4:38 PM