User's Manual
Table Of Contents
- Introduction
- Contents
- FCC Licensing Information
- Getting Started
- 1. Slide the spring action belt clip grooves into the belt clip rails on the back of the battery pack and slide it down into place until it snaps.
- 2. To remove, push the release tab on the back of the battery surface and pull the spring action belt clip upward to remove.
- 1. With the Motorola logo side up, on the battery pack, place the battery into the radio.
- 2. Push the battery into the battery compartment to fit properly into place.
- 1. Press and hold Q to check for channel activity. If you hear static, the channel is clear to use. Do not transmit if someone is speaking on the channel. Press Q again to stop monitoring the channel.
- 2. Press and hold M and speak into the microphone. To maximize clarity, hold the radio two-to-three inches away from your mouth.
- Battery and Charging Options
- Li-Ion Battery
- Alkaline Batteries
- Charging the Radio
- Battery Life
- RDX Series Factory Defaults
- Signal Strength Indicator/Channel Busy
- Talk Range
- Hands-Free Use/VOX
- With Compatible VOX Accessories
- 1. Turn radio off.
- 2. Open accessory cover.
- 3. Insert plug of audio accessory firmly into accessory jack.
- 4. Turn radio on. Radio LED will flash double green
- 5. Lower radio volume BEFORE placing accessory near ear.
- 6. To transmit, speak into accessory microphone and to receive, stop talking.
- 7. You can disable VOX operation by pressing M or removing the audio accessory.
- Setting VOX Sensitivity
- Monitoring a Channel
- Entering Programming Mode
- Programming a Channel
- Programming the Frequency
- 1. Enter programming mode (M+SB1+hold for 3 seconds).
- 2. Selects the desired Channel (using Rotary Selector).
- 3. Press M to move to the "Tens Digit" of Frequency, then scroll up or down using SB1/SB2 to set the "10's" value.
- 4. Press M to move to "Units Digit" of Frequency, then scroll up or down using SB1/SB2 to set the "1's" value.
- Programming the Interference Eliminator Code
- 1. Press M to move to the "Hundreds Digit" of Code, then scroll up or down using SB1/SB2 to set the "100's" value.
- 2. Press M to move to the "Tens Digit" of Code, then scroll up or down using SB1/SB2 to set the "10's" value.
- 3. Press M to move to the "Units Digit" of Code, then scroll up or down using SB1/ SB2 to set the "1s" value.
- Programming Bandwidth (when FCC allowable)
- Programming Call Tones
- Programming Microphone Gain
- Cloning
- Frequencies and Bandwidths
- 1
- 151.6250
- 25.00
- 16
- 151.8650
- 25.00
- 2
- 151.9550
- 25.00
- 17
- 151.8950
- 25.00
- 3
- 154.5700
- 25.00
- 18
- 151.9250
- 25.00
- 4
- 154.6000
- 25.00
- 19
- 152.7000
- 25.00
- 5
- 151.7000
- 12.5/25.0
- 20
- 154.4900
- 25.00
- 6
- 151.7600
- 12.5/25.0
- 21
- 154.5150
- 25.00
- *7
- 151.8200
- 12.5/25.0
- 22
- 154.5275
- 25.00
- *8
- 151.8800
- 12.5/25.0
- 23
- 154.5400
- 25.00
- *9
- 151.9400
- 12.5/25.0
- 24
- 154.6000
- 25.00
- 10
- 151.5125
- 25.00
- 25
- 154.6550
- 25.00
- 11
- 151.6550
- 25.00
- 26
- 158.4000
- 25.00
- 12
- 151.6850
- 25.00
- 27
- 158.4075
- 25.00
- 13
- 151.7150
- 25.00
- 14
- 151.7450
- 25.00
- 15
- 151.7750
- 25.00
- Getting Started
- UHF Frequencies
- 1
- 464.5000
- 12.5/25.0
- 15
- 461.1875
- 12.5
- 2
- 464.5500
- 12.5/25.0
- 16
- 461.2125
- 12.5
- 3
- 467.7625
- 12.5/25.0
- 17
- 461.2375
- 12.5
- 4
- 467.8125
- 12.5/25.0
- 18
- 461.2625
- 12.5
- 5
- 467.8500
- 12.5/25.0
- 19
- 461.2875
- 12.5
- 6
- 467.8750
- 12.5/25.0
- 20
- 461.3125
- 12.5
- 7
- 467.9000
- 12.5/25.0
- 21
- 461.3375
- 12.5
- 8
- 467.9250
- 12.5/25.0
- 22
- 461.3625
- 12.5
- 9
- 461.0375
- 12.5
- 23
- 462.7625
- 12.5
- 10
- 461.0625
- 12.5
- 24
- 462.7875
- 12.5
- 11
- 461.0875
- 12.5
- 25
- 462.8125
- 12.5
- 12
- 461.1125
- 12.5
- 26
- 462.8375
- 12.5
- 13
- 461.1375
- 12.5
- 27
- 462.8625
- 12.5
- 14
- 461.1625
- 12.5
- 28
- 462.8875
- 12.5
- 29
- 462.9125
- 12.5
- 43
- 466.2625
- 12.5
- 30
- 464.4875
- 12.5
- 44
- 466.2875
- 12.5
- 31
- 464.5125
- 12.5
- 45
- 466.3125
- 12.5
- 32
- 464.5375
- 12.5
- 46
- 466.3375
- 12.5
- 33
- 464.5625
- 12.5
- 47
- 466.3625
- 12.5
- 34
- 466.0375
- 12.5
- 48
- 467.7875
- 12.5
- 35
- 466.0625
- 12.5
- 49
- 467.8375
- 12.5
- 36
- 466.0875
- 12.5
- 50
- 467.8625
- 12.5
- 37
- 466.1125
- 12.5
- 51
- 467.8875
- 12.5
- 38
- 466.1375
- 12.5
- 52
- 467.9125
- 12.5
- 39
- 466.1625
- 12.5
- 53
- 469.4875
- 12.5
- 40
- 466.1875
- 12.5
- 54
- 469.5125
- 12.5
- 41
- 466.2125
- 12.5
- 55
- 469.5375
- 12.5
- 42
- 466.2375
- 12.5
- 56
- 469.5625
- 12.5
- UHF Frequencies (Continued)
- 57
- 462.1875
- 12.5
- 71
- 451.6375
- 12.5
- 58
- 462.4625
- 12.5
- 72
- 452.3125
- 12.5
- 59
- 462.4875
- 12.5
- 73
- 452.5375
- 12.5
- 60
- 462.5125
- 12.5
- 74
- 452.4125
- 12.5
- 61
- 467.1875
- 12.5
- 75
- 452.5125
- 12.5
- 62
- 467.4625
- 12.5
- 76
- 452.7625
- 12.5
- 63
- 467.4875
- 12.5
- 77
- 452.8625
- 12.5
- 64
- 467.5125
- 12.5
- 78
- 456.1875
- 12.5
- 65
- 451.1875
- 12.5
- 79
- 456.2375
- 12.5
- 66
- 451.2375
- 12.5
- 80
- 456.2875
- 12.5
- 67
- 451.2875
- 12.5
- 81
- 456.3375
- 12.5
- 68
- 451.3375
- 12.5
- 82
- 456.4375
- 12.5
- 69
- 451.4375
- 12.5
- 83
- 456.5375
- 12.5
- 70
- 451.5375
- 12.5
- 84
- 456.6375
- 12.5
- 85
- 457.3125
- 12.5
- 88
- 457.7625
- 12.5
- 86
- 457.4125
- 12.5
- 89
- 457.8625
- 12.5
- 87
- 457.5125
- 12.5
- -
- -
- -
- Interference Eliminator Codes
- Digital Interference Eliminator Codes
Safety and General Inforation
8
Warnings (Cont.)
5. To reduce risk of fire, electric shock, or injury, do not operate the charger if it has been
broken or damaged in any way. Take it to a qualified Motorola service representative.
6. Do not disassemble the charger – it is not repairable and replacement parts are not
available. Disassembly of the charger may result in risk of electrical shock or fire.
7. To reduce risk of electric shock, unplug the charger from the AC outlet before attempting
any maintenance or cleaning.
Operational Safety Guidelines
• This equipment is not suitable for outdoor use. Use only in dry locations/conditions.
• Connect equipment only to an appropriately fused and wired supply of the correct voltage
(as specified on the product).
• When not in use, disconnect the transformer from the AC outlet.
• The socket outlet to which the transformer is connected should be close by and easily
accessible.
• In equipment using fuses, replacements must comply with the type and rating specified in
the equipment instructions.
• Maximum ambient temperature around the transformer unit must not exceed 40°C (104°F).
• Output power from the transformer unit must not exceed the ratings stated on the product
label located on the bottom of the charger.
• Make sure the cord is located where it will not be stepped on, tripped over, or subjected to
water, damage, or stress.
6864110R04b.book Page 8 Friday, October 20, 2006 4:38 PM