User's Manual
Table Of Contents
- 5827 Exhibit D - User Information
- Tune-Up Procedure
- User Manual
- MANUAL COVER PAGE
- Copyrights
- CMM Labeling and Disclosure Table
- Service Information
- Document History
- Contents
- List of Figures
- List of Tables
- List of Processes
- List of Procedures
- About MTS LiTE, MTS 2 and MTS 4 Installation, Configuration and Basic Service Manual
- MTS Overview
- General Safety
- Radio Frequency Distribution System
- RFDS Theory of Operation
- MTS LiTE and MTS 2 RFDS
- MTS 4 RFDS
- Expansion Cabinet RFDS
- Site Controller
- XHUB Controller
- Base Radio
- Power Supply Unit
- Cooling Fans
- Technical Specifications
- Environmental and Standards Specifications
- Cabinet and Module Specifications
- MTS Cabinets Frequency Range
- Dimensions of the MTS Cabinets
- RF Specifications
- Transmitter Specifications
- Receiver Specifications
- Site Controller Specifications
- Internal GPS Module Input Specifications
- MTS LiTE / MTS 2 Duplexer Specifications
- MTS LiTE / MTS 2 Preselector Specifications
- MTS 4 Duplexer Specifications
- MTS 4 Post Filter Specifications
- MTS 4 Preselector Specifications
- Auto Tune Cavity Combiner (ATCC) Specifications
- Manual Tune Cavity Combiner (MTCC) Specifications
- Hybrid Combiner Specifications
- Base Radio Specifications
- Power Supply Unit Specifications
- XHUB Controller Specifications
- RX Splitter Specifications
- MTS LiTE, MTS 2, and MTS 4 Connectors
- Expansion Options
- MTS 4 Outdoor Enclosure
- Appendix A: Field Replaceable Units (FRUs)
- Appendix B: Planned Maintenance Inspection (PMI)
- Appendix C: Static Precautions and ESD Strap
- Appendix D: TETRA/Dimetra Acronyms
Figure 162: Schematic Diagram of RX Splitter
Replacing the Expansion Cabinet RX Splitter
This process outlines the recommended tasks to be performed to replace the Expansion Cabinet RX Splitter. For a list
of available FRUs, see Field Replaceable Units (FRUs) on page 405.
Process:
1 Remove the RX splitter, see Removing the RX Splitter
on page 261.
2 Reinstall the RX splitter, see Reinstalling the RX Splitter on page 261.
Removing the RX Splitter
This procedure describes how to remove the RX Splitter.
Procedure:
1 Remove the door of the cabinet completely.
2 Remove the four screws holding the front panel.
3 Loosen the two screws holding the front section of the top panel and slide off the panel.
4 Loosen the screws fastening the rear section of the top panel and slide off the panel.
5 Remove the RX cables connected to the back of the RX Splitter.
6 Loosen the two fastening screws at the front enough to free the mounting bracket.
7 Slide the RX Splitter out of the cabinet.
8 Remove the RX Splitter from the bracket and replace with the new unit.
Reinstalling the RX Splitter
This procedure describes how to reinstall the RX Splitter.
Procedure:
1 Fasten the RX Splitter onto the bracket.
2 Slide the RX Splitter into the cabinet.
3 Tighten the two fastening screws at the front.
4 Connect the RX cables to the back of the RX Splitter.
5 Slide on the top rear and front panels and fasten these with screws.
Radio Frequency Distribution System | 261
6802800U74-AD | September 2014 |
Send Feedback
Applicant: Motorola Solutions
Equipment Type: ABZ89FC5827 / 109AB-5827
Exhibit D2