User's Manual
Table Of Contents
- 5827 Exhibit D - User Information
- Tune-Up Procedure
- User Manual
- MANUAL COVER PAGE
- Copyrights
- CMM Labeling and Disclosure Table
- Service Information
- Document History
- Contents
- List of Figures
- List of Tables
- List of Processes
- List of Procedures
- About MTS LiTE, MTS 2 and MTS 4 Installation, Configuration and Basic Service Manual
- MTS Overview
- General Safety
- Radio Frequency Distribution System
- RFDS Theory of Operation
- MTS LiTE and MTS 2 RFDS
- MTS 4 RFDS
- Expansion Cabinet RFDS
- Site Controller
- XHUB Controller
- Base Radio
- Power Supply Unit
- Cooling Fans
- Technical Specifications
- Environmental and Standards Specifications
- Cabinet and Module Specifications
- MTS Cabinets Frequency Range
- Dimensions of the MTS Cabinets
- RF Specifications
- Transmitter Specifications
- Receiver Specifications
- Site Controller Specifications
- Internal GPS Module Input Specifications
- MTS LiTE / MTS 2 Duplexer Specifications
- MTS LiTE / MTS 2 Preselector Specifications
- MTS 4 Duplexer Specifications
- MTS 4 Post Filter Specifications
- MTS 4 Preselector Specifications
- Auto Tune Cavity Combiner (ATCC) Specifications
- Manual Tune Cavity Combiner (MTCC) Specifications
- Hybrid Combiner Specifications
- Base Radio Specifications
- Power Supply Unit Specifications
- XHUB Controller Specifications
- RX Splitter Specifications
- MTS LiTE, MTS 2, and MTS 4 Connectors
- Expansion Options
- MTS 4 Outdoor Enclosure
- Appendix A: Field Replaceable Units (FRUs)
- Appendix B: Planned Maintenance Inspection (PMI)
- Appendix C: Static Precautions and ESD Strap
- Appendix D: TETRA/Dimetra Acronyms
Appendix
B
Planned Maintenance Inspection (PMI)
To assist maintenance of Dimetra products, Motorola publishes advice for recommended Planned Maintenance
Inspections (PMI). For each Motorola Part Number, the Inspection Schedule indicates whether any PMI action is
required/recommended, the regularity of the recommended/required action, and a brief description of the activity. The
Inspection Schedule also indicates Motorola’s recommended PMI testing activities that should be carried out as part
of the PMI Schedule.
Always read the PMI Inspection Schedule in conjunction with the relevant Motorola or Motorola 3rd party suppliers
Standard Product Manuals and any Technical Information Bulletins (TIBs), which include the methods of access and
other useful information.
In additional to the Planned Maintenance Inspections, Motorola recommends to run the basic functional test every 24
months. These functional tests should include RF power, RF frequency, and Bit Error Rate measurements.
Motorola recommends regular site visits for other inspections, for example, site physical security checks, generator
maintenance, and so on.
Motorola also recommends the antennas and PSU/Battery/UPS tests and functional inspection according to the
respective manufacturers suggestions.
Caution: Ensure the ventilation holes and grilles on the are not covered.
Note: In the configuration with the backup battery: Check the backup battery charged by the MTS in
accordance to the manufacturers instructions.
Table 137: Required Planned Maintenance Inspection Actions
Component Required PMI Action
Site Controller Lithium backup battery Replace every 8 years.
Heat sinks and interior of the MTS
Perform periodic inspections which require cleaning oc-
casionally due to the buildup of dust. The frequency of
this inspection is dependent upon the local environment
and is more important when the MTS is operating at a
high ambient temperature.
417 | Planned Maintenance Inspection (PMI)
6802800U74-AD | September 2014 | Send Feedback
Applicant: Motorola Solutions
Equipment Type: ABZ89FC5827 / 109AB-5827
Exhibit D2