User's Manual
Table Of Contents
- 5827 Exhibit D - User Information
- Tune-Up Procedure
- User Manual
- MANUAL COVER PAGE
- Copyrights
- CMM Labeling and Disclosure Table
- Service Information
- Document History
- Contents
- List of Figures
- List of Tables
- List of Processes
- List of Procedures
- About MTS LiTE, MTS 2 and MTS 4 Installation, Configuration and Basic Service Manual
- MTS Overview
- General Safety
- Radio Frequency Distribution System
- RFDS Theory of Operation
- MTS LiTE and MTS 2 RFDS
- MTS 4 RFDS
- Expansion Cabinet RFDS
- Site Controller
- XHUB Controller
- Base Radio
- Power Supply Unit
- Cooling Fans
- Technical Specifications
- Environmental and Standards Specifications
- Cabinet and Module Specifications
- MTS Cabinets Frequency Range
- Dimensions of the MTS Cabinets
- RF Specifications
- Transmitter Specifications
- Receiver Specifications
- Site Controller Specifications
- Internal GPS Module Input Specifications
- MTS LiTE / MTS 2 Duplexer Specifications
- MTS LiTE / MTS 2 Preselector Specifications
- MTS 4 Duplexer Specifications
- MTS 4 Post Filter Specifications
- MTS 4 Preselector Specifications
- Auto Tune Cavity Combiner (ATCC) Specifications
- Manual Tune Cavity Combiner (MTCC) Specifications
- Hybrid Combiner Specifications
- Base Radio Specifications
- Power Supply Unit Specifications
- XHUB Controller Specifications
- RX Splitter Specifications
- MTS LiTE, MTS 2, and MTS 4 Connectors
- Expansion Options
- MTS 4 Outdoor Enclosure
- Appendix A: Field Replaceable Units (FRUs)
- Appendix B: Planned Maintenance Inspection (PMI)
- Appendix C: Static Precautions and ESD Strap
- Appendix D: TETRA/Dimetra Acronyms
Adding a Redundant Site Controller
This section described how to install and configure an additional Site Controller, gaining Redundant Site Controller
functionality.
Caution: You must be familiar with Man-Machine Interface (MMI) commands and their usage before
performing procedures in this chapter. Improperly applying MMI commands can result in equipment
damage.
Important:
Disable your Firewall application before attempting to transfer files.
The MTS Site Controller has the following modes of operation:
• BOOT1 – to access this mode interrupt the booting process by pressing Escape key or Control+C
combination when appropriate message is shown. A password may be required to enter this mode.
• Test Application – to access this mode enter the testapp command when in BOOT1 mode. To go
back to normal Site Controller Application enter reset -oplatform command to reboot and resume
normal operation.
• Site Controller Application – if the boot process is not interrupted, this is the default mode of
operation.
Note: When adding an additional (redundant) Site Controller, there will be some service downtime while
making physical modifications.
Process:
1 Back up the Site Controller configuration of the existing Site Controller.
See the respective restoration manual (DIPS/DIPC systems) or Service Manual (DIPM system) for MTS
Configuration Backup procedures.
Note: This assumes that the existing Site Controller is properly configured and in service.
2 Install second Site Controller.
See Installing a Second Site Controller on page 391
.
3 Restore the Site Controller Software on the second Site Controller.
See the respective restoration manual (DIPS/DIPC systems) or Service Manual (DIPM system) for details on
restoring the Site Controller software.
4 Configure E1 Links on the second Site Controller.
See the respective restoration manual (DIPS/DIPC systems) or Service Manual (DIPM system) for details on how
to configure the E1 links.
5 Configure CAN Bus on the second Site Controller.
For detailed procedures, see the respective restoration manual (DIPS/DIPC systems) or Service Manual (DIPM
system).
6 Load Ki’s into MTS.
See the respective restoration manual (DIPS/DIPC systems) or Service Manual (DIPM system) for details on
loading Ki's Into MTS.
7 Check the MTS post-restoration checks.
For details, see the respective restoration manual (DIPS/DIPC systems) or Service Manual (DIPM system).
390 | Expansion Options
Send Feedback | September 2014 | 6802800U74-AD
Applicant: Motorola Solutions
Equipment Type: ABZ89FC5827 / 109AB-5827
Exhibit D2