User's Manual
Table Of Contents
- 5827 Exhibit D - User Information
- Tune-Up Procedure
- User Manual
- MANUAL COVER PAGE
- Copyrights
- CMM Labeling and Disclosure Table
- Service Information
- Document History
- Contents
- List of Figures
- List of Tables
- List of Processes
- List of Procedures
- About MTS LiTE, MTS 2 and MTS 4 Installation, Configuration and Basic Service Manual
- MTS Overview
- General Safety
- Radio Frequency Distribution System
- RFDS Theory of Operation
- MTS LiTE and MTS 2 RFDS
- MTS 4 RFDS
- Expansion Cabinet RFDS
- Site Controller
- XHUB Controller
- Base Radio
- Power Supply Unit
- Cooling Fans
- Technical Specifications
- Environmental and Standards Specifications
- Cabinet and Module Specifications
- MTS Cabinets Frequency Range
- Dimensions of the MTS Cabinets
- RF Specifications
- Transmitter Specifications
- Receiver Specifications
- Site Controller Specifications
- Internal GPS Module Input Specifications
- MTS LiTE / MTS 2 Duplexer Specifications
- MTS LiTE / MTS 2 Preselector Specifications
- MTS 4 Duplexer Specifications
- MTS 4 Post Filter Specifications
- MTS 4 Preselector Specifications
- Auto Tune Cavity Combiner (ATCC) Specifications
- Manual Tune Cavity Combiner (MTCC) Specifications
- Hybrid Combiner Specifications
- Base Radio Specifications
- Power Supply Unit Specifications
- XHUB Controller Specifications
- RX Splitter Specifications
- MTS LiTE, MTS 2, and MTS 4 Connectors
- Expansion Options
- MTS 4 Outdoor Enclosure
- Appendix A: Field Replaceable Units (FRUs)
- Appendix B: Planned Maintenance Inspection (PMI)
- Appendix C: Static Precautions and ESD Strap
- Appendix D: TETRA/Dimetra Acronyms
Adding an Additional Base Radio to MTS 4
Follow the procedure below to install an additional Base radio for MTS 4. The images below illustrate cable
connections before adding a third Base Radio to the configuration.
Procedure:
1 Remove the Blind Plate where the additional Base Radio is to be added.
2 Label all Rx cables with labels included in the expansion kit.
3 Attach the Rx cables to the filters. Connect them according to the scheme below:
# Part no Cable type Label From To
15
3066543B02 RX cable Rx1 Filter 1 / BR# BR# / Rx1
16
Rx2 Filter 2/ BR# BR# / Rx2
17
Rx3 Filter 3/ BR# BR# / Rx3
Note: If Base Radio to be added is BR2, replace BR# with BR2 i table above, and so on.
Note: Index numbers in table above refer to cable connections shown in Cable Connections.
Note: At this stage only connect the cables to the filters.
4 Attach the Tx cable to the Tx input of the Cavity Combiner according to the scheme below:
# Note Part no Cable type From To
11
If BR2 3066543B08 Tx cable CC1 / TxB BR2 / Tx
12
If BR3 3066543B08 Tx cable CC2 / TxA BR3 / Tx
18
If BR4 3066543B08 Tx cable CC2 / TxB BR4 / Tx
Note: Index numbers in table above refer to cable connections shown in Cable Connections.
Note: At this stage only connect the cable to the Cavity Combiner (ATCC or MTCC).
5 Attach the Ethernet cable to the appropriate BR input of the Site Controller according to the scheme below:
# Note Part no Cable type From To
2
If BR2 3066544B02 Ethernet cable BR2 / SC1 SC1 / BR2
6
If BR3 3066544B04 Ethernet cable BR3 / SC1 SC1 / BR3
11
If BR4 3066544B05 Ethernet cable BR4 / SC1 SC1 / BR4
Note: Index numbers in table above refer to cable connections shown in Cable Connections.
Note: At this stage only connect the cable to the Site Controller.
Note: If the Ethernet cable is being wired from a Base Radio in one Module Cage to a Site Controller in
another Module Cage, the Ethernet cable is to be drawn outside of the Module Cage.
388 | Expansion Options
Send Feedback | September 2014 | 6802800U74-AD
Applicant: Motorola Solutions
Equipment Type: ABZ89FC5827 / 109AB-5827
Exhibit D2