Specifications

ManualsBrandsMosconi Manualscar audio amplifiersMosconi Gladen 2 Way AB Class 1x1800W Amplifier

AS 300.2 [ Rev. 2.0 - 2012/06 ]

2-channel AB class amplifier

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

CEA-2006-A SPECIFICATIONS

POWER RATING: 300 Watt per channel @ 4 Ohm < 1% THD+N

SN RATIO: >86 dBA (reference: 1 Watt into 4 Ohm)

MOS SPECIFICATIONS (Tcase = 25 °C / 4 Ohm stereo / 0.2V input level @ 14.4 Volt if not otherwise specified)

TARGET POWERs: 300 Watt per channel @ 4 Ohm

550 Watt per channel @ 2 Ohm

1100 Watt BTL mode @ 4 Ohm

1800 Watt BTL mode @ 2 Ohm (*)

EFFECTIVE POWERs: 330 Watt (260 Watt @12V6) x 2 67.8 A (η = 68.0 %) @ 4 Ohm / ST mode / 1% THD / 1KHz

562 Watt (432 Watt @12V6) x 2 123.4 A (η = 63.3 %) @ 2 Ohm / ST mode / 1% THD / 1KHz

1124 Watt (864 Watt @12V6) x 1 123.4 A (η = 63.3 %) @ 4 Ohm / BTL mode / 1% THD / 1KHz

THD @ 4 Ohm / ST mode: < 0.035 % (1KHz / 90% Power rating ref)

THD @ 2 Ohm / ST mode: < 0.035 % (1KHz / 90% Power rating ref)

DIM @ 4 Ohm / ST mode: < ----- % (Power rating ref)

DIM @ 2 Ohm / ST mode: < ----- % (Power rating ref)

DC-DC converter typology: Unregulated (upper voltage limitation)

Conversion frequency: 50 KHz (± 6 %)

Absolute maximum operation supply voltage range: 10 V ÷ 16 V

Recommended operation supply voltage range: 11 V ÷ 14.4 V

Power-on/Power-off Voltage Threshold: 9 V / 7.5 V

Mute delay time: 3 secs

Secondary voltages (Amp. / Driver / Pre.): ±52.3 V / ±7.5 V / ±13.5 V

Max output offset voltage (each channel): ±15 mV

Standby current: 1.8 mA (typical)

Quiescent consumption @ 12V: 1.4 A (no idle current regutation)

Idle current regulation (no signal): 0.1 A (each channel)

Quiescent consumption @ 12V: 1.6 A (with idle current setted)

Thermal protection consumption: 1.7 A

Battery ground vs secondary ground decoupling: 125 Ohm

Body ground vs battery ground decoupling: 65 Ohm

Bandwidth (-3dB ÷ 1 Watt): < 5 Hz ÷ 150 KHz

Input sensitivity (Power rating ref): 0.2 V ÷ 5 V

Input impedance @ 1 KHz (STEREO input): 11 KOhm

Input capacitance @ 1 KHz (STEREO input): 220 pF

Input ground decoupling: 15R

S/N ratio (AP filter 10 Hz - 500 KHz ) – Power rating ref: 93 dB

S/N ratio (AP filter 10 Hz - 22 KHz ) – Power rating ref: 110 dB (“A” weighted)

Eq. Input noise (AP filter 10 Hz - 500 KHz ): 5,29 uV

Eq. Input noise (AP filter 10 Hz - 22 KHz ): 0.75 uV (“A” weighted)

Channel separation@ 100Hz / 1KHz / 10KHz – 10 Watt ref: 83 dB / 76 dB / 60 dB

Xover functions: HIGH Pass & LOW Pass (BAND Pass allowed)

(20 ÷ 175Hz) & (50 ÷ 300Hz)

Filter slope - Filter "Q": 12 dB/oct - 0.7 (Stereo & Mono)

Thermal cutoff Threshold: 88 °C (±5°C)

ProSPEED

Fan Controller Threshold: 55 °C (±5°C)

Damping factor @ 100 Hz - 10 Watt ref (Right / Left): 168 / 228

Damping factor @ 1 KHz - 10 Watt ref (Right / Left): 163 / 221

Damping factor @ 10 KHz - 10 Watt ref (Right / Left): 114 / 160

Output impedance @ 1 KHz - 10 Watt ref (Right / Left): 24.5 mOhm / 18.1 mOhm

Load drive limitations (*): 1 Ohm / 2 Ohm (Stereo / Bridged)

Suggested fuse: 150 A (Internal)

(*) VERY IMPORTANT NOTE - READ CAREFULLY

4 Ohm ST or 8 Ohm BTL – CONTINUOUS SINEWAVE SIGNAL – pure resistive load or speaker load

2 Ohm ST or 4 Ohm BTL – MUSICAL SIGNAL – pure resistive load or speaker load

1 Ohm ST or 2 Ohm BTL – MUSICAL SIGNAL – speaker load only

- Features may change without notice -