Product Manual

CONTROLS LEGENDE
M
30
REV.0-06/07
4A Hydraulic oil level light
9 Welding socket ( + )
10 Welding socket ( - )
12 Earth terminal
15 A.C. socket
16 Accelerator lever
17 Feed pump
19 48V D.C. socket
22 Engine air filter
23 Oil level dipstick
24 Engine oil reservoir cap
24A Hydraulic oil reservoir cap
24B Water filling cap
25 Fuel prefilter
26 Fuel tank cap
27 Muffler
28 Stop control
29 Engine protection cover
30 Engine cooling/alternator fan belt
31 Oil drain tap
31A Hydraulic oil drain tap
31B Water drain tap
31C Exhaust tap for tank fuel
32 Button
33 Start button
34 Booster socket 12V
34A Booster socket 24V
35 Battery charge fuse
36 Space for remote control
37 Remote control
42 Space for E.A.S.
42A Space for PAC
47 Fuel pump
49 Electric start socket
54 Reset button PTO HI
55 Quick coupling m. PTO HI
55A Quick coupling f. PTO HI
56 Hydraulic oil filter
59 Battery charger thermal switch
59A Engine thermal switch
59B Aux current thermal switch
59C Supply thermal switch wire feeder-42V
59D Pre-heater (spark plug) thermal switch
59E Supply thermal switch oil/water heather
59F Electropump thermal switch
63 No load voltage control
66 Choke control
67A Auxiliary / welding current control
68 Cellulosic electrodes control
69A Voltmeter relay
70 Warning lights
71 Selecting knob
72 Load commut. push button
73 Starting push button
74 Operating mode selector
75 Power on warning light
76 Display
79 Wire connection unit
86 Selector
86A Setting confirmation
87 Fuel valve
88 Oil syringe
A3 Insulation monitoring
A4 Button indicating light 30 l/1' PTO HI
B2 Engine control unit EP2
B3 E.A.S. connector
B4 Exclusion indicating light PTO HI
B5 Auxiliary current push button
C2 Fuel level light
C3 E.A.S. PCB
C6 Control unit for generating sets QEA
D Ground fault interrupter ( 30 mA )
D1 Engine control unit and economiser EP1
D2 Ammeter
E2 Frequency meter
F Fuse
F3 Stop switch
F5 Warning light, high temperature
F6 Arc-Force selector
G1 Fuel level transmitter
H2 Voltage commutator
H6 Fuel electro pump
I2 48V A.C. socket
I3 Welding scale switch
I4 Preheating indicator
I5 Y/▲ switch
I6 Start Local/Remote selector
L A.C. output indicator
L5 Emergency button
L6 Choke button
M Hour counter
M1 Warning level light
M2 Contactor
M5 Engine control unit EP5
M6 CC/CV switch
N Voltmeter
N1 Battery charge warning light
N2 Thermal-magnetic circuit breaker/Ground fault interrupter
N5 Pre-heat push-button
N6 Connector - wire feader
O1 Oil pressure warning light/Oil alert
P Welding arc regulator
Q1 Starter key
Q3 Derivation box
Q4 Battery charge sockets
Q7 Welding selector mode
R3 Siren
S Welding ammeter
S1 Battery
S3 Engine control unit EP4
S6 Wire feeder supply switch
S7 Plug 230V singlephase
T Welding current regulator
T4 Dirty air filter warning light/indicator
T5 Earth leakage relay
T7 Analogic instrument V/Hz
U Current trasformer
U3 R.P.M. adjuster
U4 Polarity inverter remote control
U5 Relase coil
U7 Engine control unit EP6
V Welding voltage voltmeter
V4 Polarity inverter control
V5 Oil pressure indicator
W1 Remote control switch
W3 Selection push button 30 l/1' PTO HI
W5 Battery voltmeter
X1 Remote control socket
Y3 Button indicating light 20 l/1' PTO HI
Y5 Commutator/switch, serial/parallel
Z2 Thermal-magnetic circuit breaker
Z3 Selection push button 20 l/1' PTO HI
Z5 Water temperature indicator
04/06/07 M30-GB