Instructions
2
3
DK ENG
Additional accessories
Morsø also oers a comprehensive line of oor plates and accessory products that can fa-
cilitate the safe and ecient operation and maintenance of your Morsø stove.
Cast iron
Cast iron is a live material. There are no two ovens that are identical. This is partly due to the
tolerances of the casting process, partly because the ovens are a work of craftsmanship.
Minor unevennesses may also occur in the cast iron surface.
1.1 Unpacking the stove
3112 and 3116: After removing the outer packaging, atten it and lay onto the oor close to
the stove; this can then act as protective work surface during the assembly process.
Next, remove the legs and bolts from inside the stove. Gently lay the stove onto its back and
unscrew it from the wooden pallet. Using the bolts supplied, now screw the legs into position
on the underside of the base. The stove should now be lifted and moved into the upright posi-
tion, avoiding excess load on the back legs.
The stove is heavy and therefore it is strongly recommended that when lifting, it is under-
taken by two people. Morsø 3112 and 3116 weighs 100 kg.
3142: After removing the outer packaging simply lift the stove o the wood pallet and care-
fully move into position. The stove is heavy and therefore it is strongly recommended that
when lifting, it is undertaken by two people. Morsø 3142 weighs 120 kg.
The stove is intended for intermittent use.
1.2 Installing the stove
The stove and chimney installations MUST comply to all current National and Local Building Regu-
lations; your approved Morsø dealer or your local building control ocer can advise regarding this.
Ultimately, it is you and your installer who is responsible that the installation complies.
1.3 Chimney Sweeping
It may also be wise to consult your local chimney sweep before installing the stove. After your
stove has been installed, it is advisable to have the chimney checked and swept at least once a
year. In any case, if your chimney has not been used for some time, it should be inspected for
cracking, bird nests, etc. before it is put back into use.
1.4 Stove placement/clearance requirements
Minimum Clearance requirements apply if the stove is placed near to combustible materials.
Permitted clearances to combustible materials are also indicated on the data plate on the
rear of the stove.
In situations where the stove is to be tted into a brick or non-combustible recess, we recom-
mend that the stove is installed with at least 10 - 15 cm clearance to the wall, this will allow
heat to circulate around the stove; also the maintenance of the outside stove is easier. When
applied to masonry, a layer of wallpaper is normally classied as a non-combustible surface.
1.0 Installing your Morsø stove
Enjoy your new Morsø stove!
Morsø, the largest stove company in the Danish mar-
ket, has been making wood-burning stoves of the
highest quality since 1853. Just follow the instructions
below, and we are certain that you will be able to use
and enjoy your new stove for many years.
1.0 Installing your Morsø stove Page no.
1.1 Unpacking the stove 3
1.2 Installing the stove 3
1.3 Chimney sweep 3
1.4 Location of the stove/distance requirements 3
1.5 The chimney 5
1.6 Pipe connections 5
1.7 Connecting to a brick chimney 6
1.8 Connecting to a steel chimney 6
1.9 Draught 7
2.0 Firing/using the stove 8
2.1 Lighting instructions and fuelling intervals 9
3.0 Routine stove maintenance 12
3.1 External maintenance 12
3.2 Internal maintenance 12
3.3 Cleaning the stove 13
4.0 Alternative fuel types 14
5.0 HETAS amendments 15
Contents