Ø-Collection Instructions for Installation and Use Ø6 - (75% Efficiency) Ø8 - (75% Efficiency) UK/EN 13240 Distributed by: Morsø UK Valley Drive · Swift Valley · Rugby, Warks CV21 1TW · England MORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORS 1 E-Mail: stoves@morsoe.com · Website: www.morsoe.
Enjoy your new Ø-COLLECTION stove! Designed by Danish stove manufacturers Morsø, the Ø-Collection incorporates unique design features and, by carefully following the enclosed instructions we are certain that you will enjoy many years of safe, comfortable warmth from your stove. Cwontents Page 1.0 Installing your Morsø stove 3 1.1 Unpacking the stove 3 1.2 Installing the stove 3 1.3 Chimney sweeping 3 1.4 Stove placement/distance requirements 3 1.5 The chimney 5 1.
1.0 Installing your Morsø stove 1.1 Unpacking the stove Carefully lift the stove from the wooden pallet and set it carefully in place. We recommend that two people perform the assembly and installation procedure. Ø6 weighs 104, kg and Ø8 weighs 132 kg. The stove is intended for intermittent use. 1.
Clearance Distance to combustible materials: Model Behind the To the sides stove (A) of the stove (B) Ø6 700 mm 600 mm uninsulated flue Ø8 850 mm 550 mm uninsulated flue 600 mm To soft furnishings 1100 mm 1100 mm B 45° A Ø6 Above the stove 600 mm B B Ø-6 Model no. Dimension Skecth Location of file: U:\udv\Tegninger\Diverse\Afstand til brandbare vægge\Afstand til hjørnevæg.SLDASM Title: 08.09.09 RSV Released: A4 1:10 Format: Itemno.: Drawing no.: Drawingtype: Rev.
Hearth requirements: The stove MUST be fitted in accordance with Local and National Building Regulations. The O-serie stoves has been independently certified. During the safety test the floor temperature did not exceed 100°C. The stoves may therefor be placed onto a hearth made of non-combustible board/sheet material or tiles at least 12 mm. thick.
1.7 Connecting the stove to a masonry chimney A wall sleeve should be bricked securely into the wall of the chimney at the appropriate height and the stovepipe inserted centrally. The pipe must not extend into the actual chimney opening, but rather must reach only to the inside of the chimney aperture. The gap between the stovepipe and sleeve must be sealed using glass fibre packing rope. Only use stovepipe components that comply to National and Local Building Regulations. 1.
1.9 Draft conditions If smoke spillage occurs when the fire door is opened, it is probably due to poor chimney draft. This type of stove requires at least 12 pa of chimney draft to achieve satisfactory combustion and smoke spillage prevention. However, in cases where the stove door is opened too vigorously you could expect that slight smoke spillage may occur. If there is too much draft from the chimney, a damper device can be installed in the chimney to reduce the draft.
2.0 Firing the stove/Using your stove The heat output of your stove is regulated by means of the 3 air inlets. A preheated air supplied to the fire across the glass window. The air is supplied when the handle under the ash lip is pushed right in. Another air supply that passes through the shaking grate is used when fuel with low gas content (coke) is used. The air is controlled when the handle under the ash lip is pushed right out.
The heating capacity of the stove is regulated with an air-slide control, positioned under the ash lip. The secondary air supply is open and the primary air supply is closed. Both the primary and secondary air supply are closed. The primary air supply is open and the secondary air supply is sufficiently open for using alternative types of fuel. Stove Nominal Output (kW) Efficiency % Ø6 7,0 75 Ø8 9,0 72 Model Maximum log length (cm) Recommended weight per loading (kg.
2.1 Lighting and fuelling intervals A lot of air is needed when first lighting the stove. When starting with a totally cold stove, it may be helpful to leave the door ajar (2-3cm) during the first few minutes; the air intake should be fully open. Wood fuel burns well when placed onto an ash bed on the grate of the stove. To achieve this you should burn roughly 1-2 kg of dry kindling the first time you light the stove. You should build and maintain the ash bed to a thickness of approximately 1 cm. 1.
5. Refuelling of your stove should be done while there are still glowing embers in the bed. Spread the embers across the bottom, but concentrated mostly towards the front of the stove. 6. Place three pieces of fuel weighing roughly 0.6 kg and measuring about 25 cm in length across the embers in one layer, with spacing of roughly 1 cm between the pieces of wood. Recommended length and weight are shown on the diagram on page 9.. 7.
The stove door should normally be opened gently the first 2 - 3 centimetres, then you should wait until the pressure has equalised before opening the door all the way. This technique will prevent smoke from getting out, particularly when there is a poor draught. The stove door should never be opened when the stove is being fired vigorously. Once the wood has burned out, it becomes glowing charcoal.
3.0 Routine stove maintenance 3.1 External maintenance The surface of the stove is painted with heat-resistant Senotherm paint. If the stove is used too vigorously, the painted surface may take-on a greyish tinge. It is easily maintained by simply vacuuming the surface with a soft brush attachment and applying two light layers of paint. Ø-Collection stoves stoves are painted using a Morsø Original Black (previously called Morsø dark grey) or Morsø grey. The paint can be bought in a spray or a can. 3.
Reasons for premature wear of internal parts • Stove being used/fired too vigorously • Too much air passing through the bottom grate • Use of excessively dry wood (wood from old furniture) • Excessive debris collection on baffle plate or inner fireback (see section on cleaning) • Ash level too high in the ash pan (see section on ash).
4.0 Alternative fuel types Your new Ø-Collection stove is EN-approved for burning wood. However, the stove is capable of burning other solid fuels as manufactured smokeless coal or good quality anthracite (stove nuts). BITUMINOUS HOUSE COAL SHOULD NEVER BE USED IN YOUR STOVE. Before burning solid fuel Install the chrome iron basket into the firebox. Lighting with solid fuel All air vents must be fully open during the lighting process.
MaintenanCE parts for Ø-Collection Description Product Code Ø6 Ø8 Riddling Grate 44162500 44162500 Coal insert 33000400 33000400 Grate Frame 33000500 33000900 Baffle, lower 33001100 33008800 Baffle, upper 33002000 33008900 Draft Reducer - Glass 79000200 79000300 Tertiary Baffle 73002561 73004361 Back brick 79001000 79004700 Side brick 79001200 79004800 16
Guarantee Product Registration MORSØ 10 YEAR GUARANTEE CERTIFICATE Behind every Morsø stove is more than 160 years of dedicated stove design and manufacturing experience. Quality control has always been at the heart of the production process and detailed measures have been put into place at all key stages of the build.
IMPORTANT! How to heat safely for the environment and yourself! • Use only dry wood Use only dry (max. 20% moisture content) and untreated wood. The fuel must be split and 8 - 12 cm thick. • Light Light with dry kindling (use 1 - 2 kg). Leave the door ajar and stay close to the stove during the lighting phase. • Good layer of embers Be certain to have a good layer of embers before refilling. The wood should light within 2 minutes.