POWER SPRAYER Model: S151 and S201 Operator’s Manual BARTELL MORRISON INC. BARTELL MORRISON (USA) LLC 375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX 905-364-4201 200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-5400 FAX 732-5444 Doc. # OI – M09205 Orig. Rel. – 07/2008 Curr. Rev. – 04 Rev.
Bartell Morrison Inc. 375 Annagem Blvd. Mississauga, Ontario, Canada L5T 3A7 Toll Free (N.A.): Phone: Facsimile: (866) 501-1683 (905) 364-4200 (905) 364-4201 ORIGINAL LANGUAGE OPERATING INSTRUCTIONS FOR MORRISON POWER SPRAYERS © 2008 BY BARTELL MORRISON INC. ALL RIGHTS RESERVED.
Table of Contents 1.0 Introduction …………………………………..…………... Page 4-6 1.1 Morrison Power Sprayer…...…………………… Page 4 1.2 Options………………………….………………… Page 4 1.3 Dimensions………………………...……...……… Page 5 1.4 Sprayer Main Components……………………… Page 6 2.0 Safety Instructions…………………...…………………... Page 7-9 2.1 Read Operating Instruction……………………… Page 7 2.2 Product Safety Hazard and Alert System……… Page 7 2.3 Fueling Warning…………………………..……… Page 8 2.4 Safety Rules………………………….…………… Page 8 3.
1.0 INTRODUCTION TO THE OPERATOR: DO NOT OPERATE THE BARTELL MORRISON POWER SPRAYER UNLESS YOU HAVE READ AND STUDIED THIS MANUAL CAREFULLY. REMEMBER THAT YOU ARE THE KEY TO SAFETY. GOOD SAFETY PRACTICES NOT ONLY PROTECT YOU, BUT ALSO THOSE WORKING AROUND YOU. MAKE THIS MANUAL A WORKING PART OF YOUR SAFETY PROGRAM. For safe operation of the power sprayer, you must be a qualified and authorized operator.
1.3 Dimensions Fig. 1 BARTELL MORRISON INC.
1.4 Sprayer Main Components Fig. 2 BARTELL MORRISON INC.
2.0 SAFETY INSTRUCTIONS 2.1 READ OPERATING INSTRUCTIONS Read and understand this entire manual before attempting to operate or service the equipment described herein. Failure to follow these operating instructions could result in serious injury or death. Store this manual with the machine and ensure it is apparent and available to any users.
2.3 FUELING WARNING ALWAYS handle fuel with care. It is highly flammable. DO NOT refuel while smoking or when near open flame or sparks. Fig. 3 2.4 ALWAYS stop engine before refueling. Fill fuel tank outdoors. SAFETY RULES The instructions provided in this manual are done so to ensure the operator’s safety as well as that of other workers, the equipment, and the job site. Failure to abide by these guidelines can lead to serious personal injury and even death.
NEVER leave the power sprayer unattended while running. Children and small animals should NEVER be present in the work area during operation of the power sprayer. ALWAYS check your power sprayer for loose or missing nuts and bolts before starting. Tighten any loose fasteners and replace missing or broken parts. Perform all routine maintenance as described within this manual. Failure to do so will void your warranty and will eventually result in premature equipment failure.
3.0 SAFETY AND OPERATIONAL LABELS 6 3 4 1 6 2 BARTELL MORRISON INC.
1 Product Brand Label 2 Model and Serial Number plate 3 DANGER: Keep hands, feet, and loose clothing away from all moving parts. 4 ATTENTION: Read and understand owner’s manual before operating or servicing this equipment. 5 ATTENTION: Do not operate this equipment until the engine is checked and filled with oil. 6 NOTICE: Sprayer must be flushed and cleaned daily. Refer to page 16 for instructions. BARTELL MORRISON INC.
4.0 SPRAYER ASSEMBLY Your new Power Sprayer will arrive with everything you need in one shipping carton. Be sure to examine the content to be certain that the following items were included: Fig. 4 - Suction Hose Connection Return Hose: ½” hose/pipe Suction Hose: ¾” hose/pipe Sprayer Wand Assembly: 25 ft. of 3/8” hose and (2) 3/8” pipes with a coupler 1. Remove the sprayer from the carton and place it on the curing drum you will be using.
5.0 SPRAYER OPERATING INSTRUCTIONS Before starting engine, refer to the engine owner’s manual, follow the engine manufacturer’s instructions for proper starting procedures, and follow the steps below. CAUTION: If the material you are working with has solids in it, these will settle to the bottom of the drum. You must agitate it thoroughly before attempting to spray the material. If you do not do this, the sprayer will become clogged and possibly damage the pump. 1.
7. Be certain the spray wand is off before turning the bypass valve to the off position to pressurize the system. 8. Turn the bypass valve to the off position. You are now ready to spray. 9. Adjustments to the spray pattern can be made with the nozzle at the end of the spray wand. Turn the nozzle counterclockwise to narrow the spray pattern, and clockwise to broaden the spray pattern. Fig. 7 10. The sprayer has an adjustable pressure relief valve (See Fig. 8) on the block assembly.
11. While not spraying, turn the bypass valve on to remove unnecessary pressure from the pump. Turning off the engine when not spraying will prolong the life of the pump. 12. The return hose may be used to check for any sediment remaining lodged at the bottom of the drum. If none is detected, the suction hose can be lowered completely into the drum. If sediment remains after several minutes of spraying, it may be necessary to remove the sprayer and stir the material manually. 6.
8.0 MAINTENANCE It is essential that the sprayer be cleaned on a daily basis. Parts that fail due to improper cleaning will not be warranted. Use the following steps as a guide to proper cleaning and maintenance. 8.1 Sprayer 1. Place the suction hose into a container that has been filled with a solvent recommended by the compound manufacturer to clean spraying equipment after use. 2. Place the return hose in an empty container the same size, or larger than the one with the cleaning agent. 3.
9.0 Warranty All products sold by Bartell Morrison Inc. and Bartell Morrison (USA) LLC (the “Company”) are warranted against defects in materials and/or workmanship; excluding normal wear on wearing components and components covered by a separate original manufacturers warranty, for a period of 12 months from the date of sale to the original end user purchaser provided that certain conditions have been met. Conditions: 1.
Declaration of Conformity / Certificat de conformité / Gelijkvormigheids certificaat Declaración de Conformidad/Declaração de Conformidade/Dichiarazione Di Conformita We: Bartell Morrison Inc. 375 Annagem Blvd. Mississauga, Ontario, Canada L5T 3A7 Tel: 905-364-4200 Fax: 905-364-4201 Declare under our sole responsibility that the product to which this declaration relates is in conformity with the following standard(s) or other normative documents.
Technical Characteristics: Caractéristiques techniques: Technisch gegevens: Características Técnicas: Caracteristicas Técnicas: Qualitàs di tecnico: Model Modéle Type Modelo Modelo Modello MachineSerial Number Numéro de Série machine Serienummer machine Máquina número de série Numero de serie da maquina Numero di seria la macchina Engine Serial Number Numéro de Série moteur Serienummer motor Motor número de série Numero de serie do motor Numero di seria la motore Weight Masse Gewicht Masa Massa Massa Lbs
NOTES BARTELL MORRISON INC.
