Touch screen radio 27010 OPERATING INSTRUCTIONS
Illustration 25 24 23 22 21 20 19 1 2 18 17 16 15 14 13 6 3 4 5 7 8 9 10 11 Touch screen rod The touch screen rod is used for pressing the touch screen buttons. To store clip the rod onto the telescopic aerial as shown.
Locations of control 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Volume control Tone switch Earphone socket DC socket (DC 6V ) for adaptor (supplied). Battery compartment - (underneath the unit). Preset station buttons 1-5 Dual time button - for time 1 and 2. Memory/time button - for setting time 1 and 2 and preset radio stations. Lock switch Select button - for selecting programmed stations.
Electrical requirements Check that the voltage on the rating plate of your AC/DC adaptor corresponds with your house electricity supply which must be A.C. (alternating current). Power supply Connecting AC/DC adaptor (supplied). As soon as you connect AC/DC adaptor the clock will start working at 12:00. You will need to set the correct time. Battery low indicator The unit checks the battery voltage capacity when the AC/DC adapter is not in use.
Setting the clock time • • The clock must be set with the unit switched off. Time 1 is to set the normal time and Time 2 can be set to view an additional world time. A single press of the Down/minute button or Up/hour button advances the setting by one hour or one minute. If the button is held setting will advance rapidly.
Radio operation Note: The lock switch must be set to the unlock position. 1 Switch the unit on by pressing the Power on/off button on the touch screen display. To obtain the maximum reception for SW and FM fully extend the telescopic aerial which is located at the rear of the unit and alter the direction for best results. The aerial for the MW and LW wavebands is located inside the unit. To obtain, the maximum MW and LW reception rotate your radio. Intermediate frequencies: FM 10.7 MHz, MW/LW/SW 450kHz.
Preset stations You can store a total of 40 memory stations (10 on each waveband). 1 Tune to the required station as described for ‘Radio operation’. 2 Press the Memory/time button (a), and ‘MEMO’ will flash for several seconds. 3 Press the Preset stations buttons 1-5 or SLCT (select) button for locations 1-10. 4 Press Memory/time button (a) again, the station is now stored in the memory. It replaces any previously stored frequencies to the button in the same waveband.
Last station memory function 1 The frequency of the last station tuned to before switching off the unit will be stored in the memory. When the unit is switched on again, it will receive this station in the respective waveband. When you are changing the waveband, the last station tuned on each waveband will also be stored in memory. Setting the alarm time 1 2 3 4 5 6 When the radio is set in the off position, the display will show the clock time. (Ensure time 1 is displayed).
Snooze 1 To silence the alarm temporarily press the Snooze button which is located on the front of the unit. The alarm will sound again in 9 minutes time. You can press the Snooze button as many times as desired. Sleep function 1 2 3 4 5 6 7 Select the required station as described in ‘Radio Operation’. Switch the unit off by pressing the Power on/off button (a). Press the Sleep button (b). The radio will come on for 10 minutes and the display will show ‘10’ and SLEEP.
4 5 To cancel the timer change the timer time until the display reads ‘00’. Wait for 5 seconds the display will revert back to the time display. The buzzer will sound at the end of the set time. Press Timer button once to turn off the buzzer. After 5 seconds, the display will revert back to the time display. Display illumination The display will illuminate for 5 seconds when you touch the upper part of the display. This enables the buttons to be seen before any buttons are pressed in a dark room.
Warning labels WARNING: To reduce the risk of electric shock, do not expose this appliance or adaptor to rain or moisture. ATTENTION: To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside the unit. Refer any servicing to qualified personnel. To prevent fire or shock hazard do not expose this apparatus or adaptor to dripping and splashing. Earphones When connecting earphones to the earphone socket, the built in loudspeaker is automatically switched off.
Guarantee Morphy Richards products are manufactured to internationally accepted quality standards. In addition to your statutory rights, Morphy Richards guarantee your product to be free from manufacturing and component defects for a period of TWO YEARS from date of purchase. If your product proves to be defective within 28 days of purchase, your Morphy Richards dealer from whom the product was purchased will be pleased to replace it free of charge.
