Operating instructions

ManualsBrandsMoog ManualsSecurity CamerasVLRM24

www.videolarm.com

P B 2 4 M 2 4 / 5 8 & V L R M 2 4 / 5 8

MIMO Wireless Solutions

Installation and Operation Instructions for the following model:

PB24M24 Rugged outdoor wireless box, with a 220/110VAC input and 24VAC output for

camera, fuse protected with a wireless 2.4GHz MIMO transmitter. Directional

antenna. Pole mounting clips included.

PB24M58 Rugged outdoor wireless box, with a 220/110VAC input and 24VAC output for

camera, fuse protected with a wireless 5.8GHz MIMO transmitter. Directional

antenna. Pole mounting clips included.

VLRM24 Wireless 2.4GHz MIMO access point, 110VAC input and 24V output.

VLRM58 Wireless 5.8GHz MIMO access point, 110VAC input and 24V output.

All Moog Videolarm MIMO Wi-Fi Series CPE/ AP/ Routers

NOTE: Not all parts in images are included in every model.

Before attempting to connect or operate this product, please read these instructions completely.

81-IN5465

12-03-2010

VLRM24

VLRM58

PB24M24

PB24M58

Summary of content (17 pages)

PAGE 1
© 2009-2010, Moog Videolarm, Inc. All Rights Reserved VLRM24 VLRM58 PB24M24 or PB24M58 PB24M24/58 & VLRM24/58 MIMO Wireless Solutions www.videolarm.com Installation and Operation Instructions for the following model: PB24M24 Rugged outdoor wireless box, with a 220/110VAC input and 24VAC output for camera, fuse protected with a wireless 2.4GHz MIMO transmitter. Directional antenna. Pole mounting clips included.
PAGE 2
IMPORTANT SAFEGUARDS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER ( OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SEVICING TO QUALIFIED SERVICE PERSONNEL. Do not block any of the ventilation openings.
PAGE 3
LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship,as follows: PRODUCTCATEGORY All Enclosuresand Electronics Pan/Tilts Poles/PoleEvators Warrior/Q-View/I.R.
PAGE 4
Electrical Specifications English Contents of Box Input Power: 120VAC/240VAC 1A/.5A Power Consumption: 1Amp (120Watts) at 120VAC Power Output: 96VA at 24VAC 52Watts Heater/Blower 32Watts Camera Power An all pole main switch with a contact of at least 3mm in each pole shall be incorporated in the electrical installation of the building. Tools Required: .150” Flathead Screwdriver 7/16 Wrench or Socket 9/16 Wrench or Socket Español Energía De Entrada: 120 Consumo De Energía de VAC/240VAC 1A/.
PAGE 5
1 2 Wall Mounting: Attach unit securely with (4) 5/16”- 3/8” or 8mm hardware (not supplied). • A template is provided in the instructions with the 2 x 8 bolt pattern required for the mounting of this product. • Each fastener should be able to withstand a minimum pull out force of 600 lbs. (272kg) • • • • 3 Connecting Housing to the Power Box Open packet assembly.
PAGE 6
5 OUTPUT: (24VAC) HEATERS CAMERA 24Vac Power To Housing Optional 24Vac Output Main Switch Internal resettable fuses are supplied for the main 24VAC output lines. Do not connect heaters to camera output. The PB24 is not designed for 3 phase or 208V systems. Los fusibles restaurables internos se proveen para las líneas de salida principales 24VAC. No conecte los calentadores con la salida de la cámara fotográfica. El PB24 no se diseña para 3 fases o sistemas 208V.
PAGE 7
8 9 When using directional antenna, the AP unit and client should be aimed towards each other. Connect IP cable between power. • Conecte el cable del IP entre la energía. • Reliez le câble d'IP entre la puissance. • Schließen Sie IP-Kabel zwischen Energie an. • Conecte o cabo do IP entre o poder. • Colleghi il cavo del IP fra potere. • Al usar la antena direccional del, la unidad del AP y el cliente se deben estar dirigido hacia uno a.
PAGE 8
1 Product Description The VLRM24/58 is a Wi-Fi Station with WPA and WPA2 supplicant support. It is specially designed to act as a Transparent Wireless Bridge that associates to a service provider and authenticates using 802.1x, if required, on start up. 1.
PAGE 9
2 2.1 PB24M Series Pre-configuring PC Setup Prior to the PB24M Series configuration, a computer with its Local Area Connection set to a static IP address is required to pre-configure the device (i.e. 192.168.1.XX). In order to do so, select the “Start” menu, “Control Panel” and then “Network Connections”.
PAGE 10
3 VLRM24/58 Complete the following steps to configure a wireless link between a VLRM24/58 with a PB24M24/58: • Connect to the VLRM24/58 by opening a web browser and connecting to http://192.168.1.1. Login to the device using videolarm for the username and camera for the password. Click on the Network tab on the configuration page. Note that a static IP address of 192.168.1.1 has been assigned to the unit be default.
PAGE 11
3.2 Wireless Security Options Encryption for the wireless link is also set from this page. Select the Encryption method that is desired and enter the appropriate encryption key. Note that this same key will need to be entered in all devices connecting to the wireless network. Click the Change button in the bottom right hand corner to apply the security settings. 3.3 VLRM24/58 Complete the following steps to connect two VLRM58 units on the same wireless network using WDS.
PAGE 12
3.4 Wireless Configuration Click on the Wireless tab on the configuration page. Note that the unit is set to a Wireless Mode of Access Point and the default SSID for the wireless network is set to videolarm. 3.5 Changing Wireless Mode Change the Wireless Mode to Access Point WDS. Place a check mark in the Auto box beside the selection. Connect to the second device and complete the proceeding steps. In most cases the units will connect to one another using the Auto mode.
PAGE 13
The MAC address for each unit can be located on the Main tab where it shows the units status. There MAC address can be found in three separate locations on that screen under LAN MAC, WAN MAC, and AP MAC. All three MAC address will be the same. Log into each unit, take note of the listed MAC address, and enter it into the WDS Peers box on the other unit.
PAGE 14
4.1 Wireless Configuration Click on the Wireless tab on the configuration page. Note that the Wireless mode for this unit is set to Station and the default SSID for the wireless network is set to videolarm. The default SSID can be changed by clicking on the Select button next to the SSID box. A new window will appear that will show all of the wireless networks within range of the device.
PAGE 15
5 Adding Multiple PB24M Series Devices to a Wireless Network By default each PB24M Series is configured with the IP address of 192.168.1.100. If there is more than one PB24M58 on the wireless network, then you will need to change the default IP addresses on each additional device. For example Unit 1 could retain the default IP address of 192.168.1.100. Unit 2 would need to have its address changed, so it could have 192.168.1.101 assigned to the Network Configuration. Unit 3 could have addresses of 192.
PAGE 16
PAGE 17
Wireless IP & Mac Address Form For your convenience and future reference, the following form has been included to record your wireless surveillance systems IP and Mac addresses. Once completed, remove the form from instruction packet and place in a secure place or inside the Moog Videolarm wireless product. The information recorded will prove beneficial when servicing or expanding your wireless system. Camera # 1 IP Address 192.168.1.